LX700 SERVICE MANUAL 020-000120-01 * Projection lens is optional. Chassis No. 103-020103-01-00 Match the Chassis No. on the unit's back cover with the Chassis No. in the Service Manual. If the Original Version Service Manual Chassis No. does not match the unit’s, additional Service Literature is re- quired.
Note on Soldering ............A16 Test Points and Locations ........46 Service Adjustment Data Table ........ 47 Chassis Description ............ 65 Chassis over view ............. 65 Input & signal processing stage ....... 66 LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
Since the lamp is very high temperature during units operation replacement of the lamp should be done at least 45 minutes after the power has been turned off, to allow the lamp cool-off. LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety stan- dards against risk of fire, casualty and electrical hazards. LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
To reset the thermostat, disconnect the AC cord and leave the projector at the normal surrounding temperature for about 45 minutes. The thermostat will automatically reset when the internal temperature becomes normal. Thermal protector (SW905) LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
After opening the lamp cover for replacing the lamp ass’y, place the lamp cover correctly otherwise the projector cannot turn on. Lamp cover sensor Filter cartridge sensor Filter cartridge switch (SW1861) switch (SW1891) LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
• The WARNING TEMP. indicator continues to blink even after the temperature inside the projector returns to normal. When the projector is turned on again, the WARNING TEMP. indi- cator stops blinking. WARNING TEMP. blinking red LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
AC power cord. blink CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN AB- NORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
When the symptoms above are noticed, contact your autho- rized dealer or service station for proper cleaning. ORDER REPLACEMENT FILTER CARTRIDGE Type No. 003-001726-01 Service Parts No.: 610 334 3747 LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
Select Reset and the “Scroll counter Reset?” appears. Another confirmation dialog box appears, select [Yes] to reset the Scroll counter. Select [Yes], then another confirmation box appears. Select [Yes] again to reset the Scroll counter. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -10-...
For continued safety, replace with a lamp of the Type No. 003-120458-01 same type. Do not drop the lamp or touch the glass Service Parts No. 610 341 1941 bulb! The glass can shatter and may cause injury. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -11-...
The projector used time and lamp used time will be displayed on the screen briefly as follows. Projector used time Counter Lamp mode Projector 500 H Lamp Normal 200 H 300 H Corresponding value 600 H Total lamp used time LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -12-...
Since the LCD panel is equipped with an electronic cir- cuit, never use any liquids (water, etc.) to clean the unit. Use of liquid may cause the unit to malfunction. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -13-...
5. Remove 1 screw D on each stopper of the optical filter ass'y and take the optical filter ass'y upward off. See chapter "Optical Parts Disassembly" for further information of optical parts disassembly. Release button Prism shield cover Fig. 1 Fig. 2 Shutter assembly Fig. 3 Fig. 4 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -14-...
This is complete the resetting of the security function. The PIN code lock and Logo PIN code lock are reset as the initial PIN code at the factory and the Key lock function is disabled. Please refer to the owner's manual for further information of the security functions. LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
Shutter assy disassembly 1 Remove 2 screws A (M3x6) and take the prism shield cover off. 2 Remove 2 screws B (M2.5x5) and take the shutter assembly off. Prism shield cover Shutter assy LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -17-...
Cabinet top Press here to unhook LED board 2-1 LED board removal 1 Remove 2 screws F (T3x8) and take the LED board and LED holder off. Fig. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -18-...
Page 21
Filter cartridge Filter cover Flat screwdriver Turn the flat screwdriver in the arrow direction to unhook the filter cover's hinges. Note: Be careful not to scratch the filter cover and holder. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -19-...
Page 22
2 Remove 6 screws B (M3x6) and take the main shield cover top off. 3 Remove 1 screw C (M3x6) and take the main board off. 4 Remove 2 screws D (M3x6) and take the main shield cov- er bottom off. Main board LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -20-...
1 Remove 4 screws D (T3x8) and 4 screws E (T3x10- 1 Remove 6 screws F (T3x8) and take the fans (FN904, black) and take the AV board off. FN905, FN906) off. FN905 FN906 FN904 AV board LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -21-...
2 Remove 5 screws G (M3x6), 1 screw H (M4x8), 2 screws J (M2.8x4) and take the power board off. Isolation sheet Note: The isolation sheet must be placed as shown in the figure above. Isolation sheet Isolation sheet Power board LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -22-...
7-1 Ballast box disassembly 1 Remove 2 screws D (M3x6) and take the shield case top off 2 Remove ballast board from the shield case bottom. Isolation sheet Ballast board LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -23-...
2 Remove 1 screw C (T3x6) and take the lens shift sen- sor board off. 3 Remove 2 screws D (T2x4) and take the lens shift mo- tor off Lens shift motor Lens shift motor Sensor board LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -24-...
9 Cabinet front removal 1 Remove 4 screws A (T3x8) and take the cabinet front RC front board upward off. 2 Remove 1 screw B (T3x8) and take the RC front board off. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -25-...
1 Remove 2 screws C (T3x8), 3 screws D (T4x35), and take fan (FN901) and holder off. 2 Remove 1 screw E (T3x14) and take the wind sensor (S901) off. S901 FN901 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -26-...
4 Take the filter switch board off, and remove 1 screw G(T3x8) and take the filter round sensor board off. 5 Remove 2 screws H (T4x8) and filter motor off. Latch Filter shaft Filter switch holder board Filter round Filter motor sensor board Filter bottom cover LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -27-...
Page 30
4 Take the duct top (LMP) upward off and remove the lamp cover switch board off. 5 Remove fan (FN903) upward off. Duct (PBS) Duct top (LCD) FN908 Duct top (LMP) Lamp cover switch board FN902 FN903 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -28-...
4 Slide the lens lock lever A on the projector to “UN- LOCK” (UPPER) position and remove the Projection Lens ass’y off. Note : When making unlocking, attach your hand to pre- vent the lens fall. Lever A Light block plate LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -29-...
Page 32
2 Remove 2 screws B (M2.5x5) and take the shutter assy upword off. 3 Remove 4 screws C (M2.5 x10) and take the LCD pan- el/prism assembly upward off. Shutter assembly LCD panel/prism assembly LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -30-...
Page 33
These LCD panels are installed with precision at the factory. When replacing the LCD panel, should be replaced whole of the LCD panels and prism ass’y at once. When replacing LCD Panel/Prism ass’y, take the optical and electrical adjustments following to the chapter "Ad- justment". LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -31-...
Page 34
Prism Ass’y backward or forward by turning the screwdriver left or right to obtain the proper focus. Confirm the focus at TELE and WIDE zoom. 5 Tighten 4 screws A to fix the LCD Panel/Prism ass’y. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -32-...
Page 35
Mount the pre-polarized glasses and polarized glasses as shown in the figure below. LCD panel/Prism top view Film side Red Marker B-LCD panel R-LCD panel Prism Blue Marker Film side Film side Green Marker G-LCD panel LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -33-...
Page 36
1 Remove 1 screw A (M2.5x5) on each stopper and take the polarized glasses upward off. Polarized glass/ Optical filter ass'y Glass holder Stopper film Polarized glass (in) Optical filter (HCP) Glass holder Blue Green LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -34-...
Page 37
Optical filter-HCP (G) Polarized glass-in (B) Marker Optical filter-HCP (B) Optical filter-HCP (R) Polarized glass-in (R) * Polarized glasses should be mounted as the film attached side is facing the LCD panel side. TYPE-R LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -35-...
Page 38
2 Remove the optical filter (LC-CS), polarized glass (IN/GB) and condenser lens (G) upward off. Optical filter (LC-CS) Condenser lens (G) Polarized glass (IN/GB) * Mount the optical filter (LC-CS) as shown in the figure. Optical filter (LC-CS) LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -36-...
Page 39
1 Remove 1 screw A (M3x6) on the thermal protector, 1 screw B (T3x10) on the ballast trigger and 5 screws C (T3x10). 2 Unhook 4 hooks D on the optical base top and take the optical base top upward off. Ballast trigger Thermal pro- tector LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -37-...
Page 40
DICHROIC MIRROR (G) OPTICAL FILTER (LC-CS) MIRROR(R) Shield Plate Note: The parts indicated with (*) are fixed with the adhesive onto the optical base bottom, so these parts are not the replaceable parts. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -38-...
Page 41
Printed marker Stopper Dichroic mirror Mount them as shown in the figure below. Pay attention to the direction of the printed parts no. on the mirror. Printed marker Printed marker LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -39-...
For further details, refer to the operation manual of the serial no. setting tool [SST LITE v1.00]. Those software are including in the service CD-ROM listed below; PROJECTOR SERVICE TOOL CD-ROM v4.20 SERVICE CODE: 610 343 5596 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -40-...
This adjustment should be taken in order of G-panel, R-panel and B-panel. This adjustment should be taken in the dark room to adjust precisely. Lever B (Polarized glass) Lever C (Optical filer) LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -41-...
ICs as the mentioned on the service ad- justment table. As these data are not the same data as LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -42-...
250 - 11 FN901 TPFN7 13.8 +0 -0.1Vdc 250 - 12 FN908 TPFN8 5.0 +0.1 -0Vdc After the auto-calibration completed, "OK" will appear 250 - 13 FN908 TPFN8 13.8 +0 -0.1Vdc on the screen. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -43-...
Page 46
ADC-Red Gain Input mode Video mode (Composite) ADC-Blue Gain Input signal 100% color bar signal Black and noisy Black and noisy image appears image appears 16-step gray scale 100% full color bar LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -44-...
Page 47
If not, the adjustment is failed. Try again. 50% gray, 60% gray, 70% gray, 80% gray 4. Check proper white balance and gray scale are ob- tained in the selected input mode. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -45-...
Alpha BB Blue 0 - 1000 20/20/20/20/20/20/ 20/20/20/20/20 FPGA Software version FPGA Software Version Info. Read only Hardware version FPGA Software Version Info. Read only Horizontal total Read only Vertical total Read only LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -48-...
Page 51
Ye Overlay Control: Manual value Select at Fix AV-Cinema 0 ~ 1 YE_APL_A0 Min: X-Cordinate at Point 0(%) 0 ~ 127 YE_APL_A1 Min: X-Cordinate at Point 1(%) 0 ~ 127 YE_APL_A2 Min: X-Cordinate at Point 2(%) 0 ~ 127 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -49-...
Page 56
Flow Ideal Data 5 Flow Sensor Theory Value No.5 Corresponding to Fan Volt No.5 0 - 1023 Flow Ideal Data 6 Flow Sensor Theory Value No.6 Corresponding to Fan Volt No.6 0 - 1023 1023 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -54-...
Page 58
* Fan voltage adj. Fan 7 Max Adjust (DAC) 0-255 * Fan voltage adj. Fan 8 Min Adjust (DAC) 0-255 * Fan voltage adj. Fan 8 Max Adjust (DAC) 0-255 * Fan voltage adj. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -56-...
Page 59
0000-9990 Normal Fan7 Max 0000-9990 Normal Fan8 Min 0000-9990 Normal Fan8 Max 0000-9990 Eco Fan Control Min Temp 20-100 Temp Sensor Control Start/End Temp St Eco Eco Fan Control Max Temp 20-100 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -57-...
Page 60
Black/White Level Area Height 0 - 4095 OFFSET Target Black Level Adj target 0 - 1023 OFFSET Tolerance Black Level Adj telerance 1 - 1023 GAIN Target White Level Adj target 0 - 1023 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -58-...
Page 61
Disp Line 0 - 4095 Composite (SECAM) Composite / S-Video Disp Dots 0 - 4095 H Back Porch 0 - 4095 V Back Porch 0 - 4095 Disp Line 0 - 4095 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -59-...
Page 62
YCbCr (1080i - 50) Total Dots 0 - 4095 2640 Disp Dots 0 - 4095 1872 H Back Porch 0 - 4095 V Back Porch 0 - 4095 Disp Line 0 - 4095 1052 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -60-...
Page 63
RGB Video (1035i) Total Dots 0 - 4095 2200 Disp Dots 0 - 4095 1873 H Back Porch 0 - 4095 V Back Porch 0 - 4095 Disp Line 0 - 4095 1012 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -61-...
Page 64
100 - 5000 1000 LIMIT_CONTRAST Ye Auto : PC Real : CAL_CONT RESULT CONTRAST (Read only) Ye Auto : PC Real : CONT_USE Used Rate at Black Balance (x0.001) 100 - 5000 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -62-...
Page 65
0 - 1000 Green ColorA Y x0.001(0.000~1.000) 0 - 1000 Green ColorB X x0.001(0.000~1.000) 0 - 1000 Green ColorB Y x0.001(0.000~1.000) 0 - 1000 Calcurated G Color X x0.001(0.000~1.000) (Read only) 0 - 1000 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -63-...
Page 66
0: Transparent Limit, 1: Voltage Limit 0 - 1 VTUsed Rate DAC 0 - 100 CALC_STATUS Calculated Result 0 - 9 DAC CALC DAC Adj Starts when the Value is set to 10. 0 - 10 LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -64-...
• • • dim • • • blinking slow • • • off (approx. 2 seconds ON, 2 • • • dim (red) • • • Differ according to conditions. seconds OFF) LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -74-...
Page 77
When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights orange. When this indicator lights orange, replace the projection lamp with a new one promptly. Reset the lamp counter after replacing the lamp. LX700 Service Manual Rev. 1 (11/08)
Page 78
The shutter is out of control. (The projector is in the cooling mode.) The shutter is out of control. (The projector is in the stand-by mode.) In that case, contact the service station immediately. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -76-...
2 The history log will be reset when the Data Value is set to "10". The value automatically returns to "0". * How to enter the service mode and select the group, item and data value, see "Service Adjustment Menu Operation". LX700 Service Manual Rev. 1 (11/08)
In the above case, because the failure occurs on the 6V power supply on the main board, the failure is also detected on the 3.3V and 1.8V power supply on the AD circuit on the main board. * See "Power Failure Detection System" for further description of the Error Information. LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
Select Input 2 Video Auto PC Adj. Select Input 2 Y, Pb/Cb,Pr/Cr Keystone UP Select Input 2 RGB Keystone DOWN ON Start ON Keystone RIGHT ON Start OFF Keystone LEFT Select Input 3 Video LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -82-...
( For each sensor, two digit and the tenth place numbers are displayed with a space between each temperature.) Communication failure The tables show the typical command lists for controlling the projector. Please consult your local dealer for further information of other commands. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -83-...
IIC Bus 0 PW_SCL0 IIC Bus 0 ZOOM+_EX Zoom+ Drive Output LB_PW_UART UART for Lamp Ballast PW_LB_UART UART for Lamp Ballast PW_SDA2 IIC Bus 2 PW_SCL2 IIC Bus 2 SCART Blue Input LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -84-...
Waveform VIDEO signal <VIDEO> HSYNC signal <TP_HS> VSYNC signal <TP_VS> S&H signal <TP501-TP561> R-S&H signal <TP501> G-S&H signal <TP531> B-S&H signal <TP561> OPT Drive <TP4414-TP4415> LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -87-...
Protector FN906 Cooling Fan S901 FN904 Wind Sensor Cooling Fan FN908 FN907 Cooling Fan Cooling Fan LP900 (Power) Lamp Ass’y FN903 Cooling Fan FN901 Cooling Fan FN902 Cooling Fan M901 Filter Motor LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -97-...
Page 100
103-020103-01-00 Electrical Parts List Accessories (see accessories parts list) REMOTE CONTROL QUICK SETUP GUIDE CD-ROM,OWNERS MANUAL CORD,POWER CABLE,USB CABLE,INTERFACE ASSY,SPACER ASSY, COVER LENS ASSY,MOUNTING LENS LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -98-...
Page 132
103-020103-01-00 Electrical Parts List Key No. Part No. Description Key No. Part No. Description LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -130-...
103-020103-01-00 Mechanical Parts List Cabinet Parts Location LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -131-...
Page 134
103-020103-01-00 Mechanical Parts List Lens Shift Assembly M02-4 M02-2 M02-1 M02-3 Filter Holder Assembly LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -132-...
Page 135
103-020103-01-00 Mechanical Parts List Shutter assembly LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -133-...
Page 136
L02L L02R (Green) L02L-2B/L02R-2B L02L-1B/L02R-1B L02L-2G/L02R-2G L02L-1G/L02R-1G (Blue) L02L-2R/L02R-2R L02L-1R/L02R-1R Note: Parts for L02-1 and L02-2 differs according to type of LCD panel/prism assembly. (Red) LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -134-...
Page 137
Refer to the chapter of optical disassembly for the mounting direction of each part. (Green) L04-G (Blue) L03L-G/L03R-G L03L-R/L03R-R L04-B L04-R L03L-B/L03R-B (Red) Note: Parts for L03 differs according to type of LCD panel/prism assembly. TYPE-L LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -135-...
Page 138
L01-4 L01-6 L01-7 L01-12 L01-1 L01-2 L01-9 Note: The parts indicated with ( ) are fixed with the adhesive onto the optical base bottom, so these parts are not the replaceable parts. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 -136-...
LX700 103-020103-01-00 These schematic diagrams and printed wiring board drawings are part of the service manual original for chassis No. 103-020103-01-00 model LX700. File with the service manual No. SM5111018-00. Note: All the information of part numbers and values indicated on these diagrams are at the beginning of production.
Mark Type number Mark Tolerance (nH) Mark Tolerance (%) 2SA1179N 2SA1037K 2SA1037AK 2SC2812/N 2SC2412K ±0.25 ±2 M6, M7 R, S R, S ±0.5 ±5 L6, L7 R, S ±0.3 ±10 ±0.2 ±15 ±20 LX700 Service Manual Rev. 1 (11/08) 020-000120-01...
Use a soldering iron which is 70 W or equivalent, and which lets you adjust the tip temperature up to 450 °C (842 °F) It should also have as good temperature recovery characteristics as possible. LX700 Service Manual Rev. 1 (11/08) 020-000120-01 Diagrams & Drawings (103-020103-01-00)