Shooting grip with wireless remote commander (25 pages)
Summary of Contents for Sony CA-570
Page 1
CAMERA ADAPTOR CA-570 CA-570P MAINTENANCE MANUAL Part 1 1st Edition (Revised 1) Serial No. 18001 and Higher: CA-570 (UC) Serial No. 38001 and Higher: CA-570 (J) Serial No. 48001 and Higher: CA-570P (CE)
Page 2
électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. CA-570 P1...
Manual Structure Purpose of this manual This manual is the maintenance manual part 1 for Camera Adaptor CA-570/570P. This manual is intended for use by trained system and service engineers, and provides the installation and maintenance information that is necessary at the time of primary service.
1-1. Checking ROM version 1-3. Connectors and Cables 1-3-1. Connector Input/Output Signals When the CA-570/570P is to be connected to the BVP- 550/550P, be sure to check that the ROM version for IC36/ . PROMTER AT-95 board of the camera is Ver. 4.00 or higher. If ROM...
Page 6
MIC IN (Y) GND (PGM) (0 dBu = 0.775 Vrms) INCOM _20 dBu RECEIVE OUT (with INCOM level control set to mechanical center) PGM 1/2 OUT _20 dBu (with PGM level control set to mechanical center) 1-2 (E) CA-570 P1...
Page 7
STANDBY: +9.0 V, Zo < 10 kZ _0.5 MONITOR: Zi = 750 Z No connection CF OUT Color Framing No connection No connection (0 dBu = 0.775 Vrms) VTR connector is disabled when the CCU is connected. 1-3 (E) CA-570 P1...
Page 8
VTR Action or when the servo is REC START into STOP lost mode, or in mode by itself REC mode (REC RESET signal does not appear when VTR is put into STOP mode by operating the camera) 1-4 (E) CA-570 P1...
Page 9
67 IIC DATA IN/OUT (CA) 5 V p-p, 4700 Z, Pull up IIC CLOCK IN (ST) 5 V p-p 68 IIC DATA IN/OUT (ST) 5 V p-p, 4700 Z, Pull up (0 dBu = 0.775 Vrms) 1-5 (E) CA-570 P1...
(10P FEMALE) HIROSE HR10R-10P-10P equivalent *1: Use of REMOTE cable enables to monitor video signals. *2: If using a cable of length different from a standard product, consult your Sony organization. 4. Disassemble as illustrated and unsolder. 1-6 (E) CA-570 P1...
1-3. Connectors and Cables 1-3-4. Wiring Diagrams for Cables CCZ Cable 26P CONNECTOR (FEMALE/MALE) (WIRING SIDE) 1-7 (E) CA-570 P1...
Page 12
White Brown White Brown Brown 8P CONNECTOR(MALE) 8P CONNECTOR(MALE) (WIRING SIDE) (WIRING SIDE) REMOTE Cable (supplied with RM-B150) (Outer sheath color : Black) Black White White Brown White 8P CONNECTOR(MALE) 8P CONNECTOR(MALE) (WIRING SIDE) (WIRING SIDE) 1-8 (E) CA-570 P1...
Monitoring is enabled OFF: Monitoring is disabled S1-4 Turns on and off the function to monitor the VTR playback audio by the earphone while the VTR is playing back Monitoring is enabled OFF: Monitoring is disabled 1-9 (E) CA-570 P1...
Page 14
RF cable (green) and connect it to a proper connector on the DM-116 board as shown in the figure above In addition, be sure to change the setting of S5 and S6 switches on the DM board of the CCU from TX to RX 1-10 (E) CA-570 P1...
Page 15
S4/DM-116 board selects whether the PROMPTER signal is input (CCU8CAM) or is output (CAM8CCU) GENLOCK: Select to input a VBS or a GENLOCK signal Check that the S1/DM-116 board is set to PROMPT side 1-11 (E) CA-570 P1...
Page 16
1-4. Function of Internal Switches AU-237/237P board CA-570 (UC) : S/N 18001 and Higher CA-570 (UC) : S/N 10001 through 18000 CA-570 P (CE) : S/N 48001 and Higher CA-570 P (CE) : S/N 40001 through 48000 S3 * S5 * S301 S4 *...
Page 17
Normal mode S411 TRACKER Selects the TRACKER TALK level at the TRACKER connector 0 (0 dBu) (T) 0/_20 0 dBu (Standard level) _20: _20 dBu (Select when input level is too high) (0 dBu = 0.775 Vrms) 1-13 (E) CA-570 P1...
Page 18
Back tally lamp is lit OFF: Back tally lamp is unlit S351 Turn on and off the function to monitor the MIC input by the headset connected to MONITOR the INCOM connector Monitoring is enabled OFF: Monitoring is disabled 1-14 (E) CA-570 P1...
Page 19
RET VIDEO OUT (in connection with CCU) PB VIDEO OUT (in connection with VTR) High VBS OUT RET VIDEO OUT (in connection with CCU) PB VIDEO OUT (in connection with VTR) High MONITOR OUT X: Don’t care. 1-15 (E) CA-570 P1...
Cable-lenght limitation for prompter signal transmission CCU → CAM CAM → CCU CCU-700 CCU-550 8.5 mm 1000 m 700 m 8.5 mm 500 m 400 m 14.5 mm 2000 m 1400 m 14.5 mm 1000 m 800 m 1-16 (E) CA-570 P1...
Page 21
/731/740/741 /731/740/741 45 m *3: When the CA-570/570P is connected with the CCU-550/550P/550A/550AP, use of intercom transmission channel is limited to only one channel. In this case, use the INCOM 1 connector for the CA-570. For the CA-570P, both INCOM 1 and INCOM 2 connectors can be used.
Page 22
VIDEO CASSETTE RECORDER BVV-5/5PS BETACAM ADAPTOR CA-553 CCZ CABLE CAMERA ADAPTOR CA-3A RECORDER UNIT DNV-5 *5: When the CA-550/550P is connected to the RM-B150, video signals cannot be output from the MONITOR connector of the RM-B150. 1-18 (E) CA-570 P1...
Page 23
REMOTE REMOTE SELECTOR CONTROL CONTROL CAC-6 UNIT(*5) UNIT RM-B150 RM-P9 VIDEO CASSETTE RECORDER BVV-5/5PS BETACAM ADAPTOR CA-553 CCZ CABLE CAMERA ADAPTOR CA-3A RECORDER UNIT DNV-5 CA-57A/57AP CCU-370/370P CA-55A/55AP CCU-355/355P CA-50A/50AP CCU-350/350P CAMERA CAMERA ADAPTOR CONTROL UNIT 1-19 (E) CA-570 P1...
MB-783 Equipment connected to TRACKER connector Equipment connected to REMOTE connector 2-3-2. Standard Tightening Torque for Screws The standard tightening torque for the screws used in CA-570/CA-570P are as follows. Screw type Tightening torque 19 x 10 N.m (1.9 kgf.cm) M2.6...
3. Press the MIC LEVEL control or set the ENTER/CANCEL switch to ENTER. 4. The menu page is returned to the previous page every time the ENTER/CANCEL switch is set to CANCEL. 5. To cancel the menu operation, set the DISPLAY switch to OFF. 2-3 (E) CA-570 P1...
Page 28
OHB-450/550 series Viewfinder BVF-10/C10W/20W series Supply power from a camera control unit CCU-550/700/700A series, AC adaptor AC-550/550CE or VTR. Switches and Button VF DISP switch DISP MENU MENU SEL switch LEVEL CANCEL button <FRONT VIEW> CANCEL 2-4 (E) CA-570 P1...
Page 29
. When the camera adaptor is not connected to the CCU, the columns 1 through 3 will display “– –”. . Refer to BVP-550/550P/570 maintenance manual for details on descriptions on columns of “OHB/PR” and “CAM”. 2-5 (E) CA-570 P1...
2-6. Recommended Replacement Parts 2-6. Recommended Replacement Parts Parts listed below are recommended replacement parts. They are subject to cracks with the lapse of time. Check sometimes by visual, and replace as necessary. Name Sony Part No. Remarks COVER, CONNECTOR 3-187-015-0X CAP, CONNECTOR...
5. Install a new connector in the reverse order of removal. [Note|at|installation] [Note|at|installation] [Note|at|installation] [Note|at|installation] [Note|at|installation] When reinstalling the FL-249 board, refer to Section 2-9 for proper connection. CN15 CN14 INCOM1 connector K2.6 MB-783 board K2.6 < Left side > 2-7 (E) CA-570 P1...
1. Remove the right side panel referring to Section 2-1. 2. Remove the two screws. Disconnect CN4 and CN5 to remove the DC/DC converter. 3. Install in the reverse order of removal. B2.6 x 5 DC/DC converter B2.6 x 5 2-8 (E) CA-570 P1...
CN-1438 board AC/DC converter Unlock and disconnect in the direction of arrow < Step 3 > B2.6 x 5 CN-1438 board B2.6 x 5 < Harness routing > 2-10 (E) CA-570 P1...
Page 35
The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.