2.7 inch lcd electronic hd viewfinder for hdcam camcorders (60 pages)
Summary of Contents for Sony CA-702
Page 1
CAMERA ADAPTOR CA-702 CA-702P MAINTENANCE MANUAL 1st Edition (Revised 2) Serial No. 10001 and Higher: CA-702 Serial No. 40001 and Higher: CA-702P...
Page 2
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
Manual Structure Purpose of this manual This manual is the maintenance manual for Camera Adaptor CA-702/702P. This manual describes the information items necessary when the unit is supplied and installed, items that premise the service based on the components parts such as alignment, schematic diagrams, board layouts and spare parts lists, assuming use of system and service engineers.
90P/90WSP, be sure to check the ROMs version. If the ROM(s) version is not adequate, ROM replace- ment is required. Please consult your Sony service representative.The function of CA-702/702P may be restricted depending on an equipment connected to the CA-702/702P. For details, refer to the operation manual “Operation Modes” supplied with the CA-702/702P.
1-3. Connecting Connectors and Cables When external cables are connected to the connector of this unit, the hardware listed below (or the equivalents) must be used. Panel indication Matching connector(cable) Sony part No. VIDEO SDI IN, OUT 1-569-370-12 DC IN XLR 4P, FEMALE...
BATT OUT(_) UNREG GND UNREG GND —— BATT REM —— LIGHT CONT EXT DC (+) 12 V (10.5-17 V) BATT OUT(+) DC OUT: XLR 4-pin (female) <External view> Pin No. Signal UNREG GND —— —— DC OUT 1-3(E) CA-702 CA-702P...
Page 12
PB VIDEO IN (X) VS 1 Vp-p, Zi = 75 Z R-Y VIDEO OUT(X) Zo = 75 Z PB VIDEO IN (G) R-Y VIDEO OUT(G) 700 mVp-p (CA-702) SAVE: +4.5 ± 0.5 V, AUDIO MONITOR IN/ B-Y VIDEO OUT(X) 525 mVp-p (CA-702P) ...
1-5. Setting of Switches on Board 1-5. Setting of Switches on Board For the factory-use switch, do not change the factory setting. RE-153 board TP106 To validate the setting, turn on the power of CA-702/P again. TP107 TP105 TP108 TP104...
Page 14
Factory setting: OFF S102-4 (SDI power forced supply) The power of an SDI circuit is turned on irrespective of the mode used. OFF: The power is saved when an SDI circuit is not used. Factory setting: OFF 1-6(E) CA-702 CA-702P...
Page 15
DIF-67 BOARD (A SIDE) Factory setting: OFF S1-4: DEC VCO ADJ OFF: Used during normal operation. The internal VCO of an SDI decoder (CXD1342R) is set to the free-running state. Factory setting: OFF 1-7(E) CA-702 CA-702P...
DIF-67 and AD-150/P boards. The video and color framing pulses are written in asynchronous FIFO (IC7, IC13 , and IC15) in the timing of the HD pulse. 1-9(E) CA-702 CA-702P...
Page 18
The VBS and SDI signals output to the CCZ connector are switched to the SDI output signal or compos- ite signal (sent from the DA-130/P board) according to the connected portable VTR (detected at pin 14 of a CCZ connector), irrespective of the SDI/COMPOSITE switch setting. 1-10(E) CA-702 CA-702P...
CN-1528 board CN12 CN11 B3 x 8 CN10 (Blue) CN13 B3 x 8 (Red) Inside panel (Green) Loosen the three screws and remove the inside panel. Coaxial cables (These screws are not pulled out.) B3 x 8 1-11(E) CA-702 CA-702P...
HN-252 board 40-pin connector 4. Attach a new 40-pin connector in the reverse order of removal steps. 5. Check that the 40-pin connector is free to move by hand. 40-pin connector Do not reuse the disconnected 40-pin connector. 1-12(E) CA-702 CA-702P...
1. Slide portions A in the direction of the arrow and insert the flexible cared wire as far as it will go with the conductive surface down. 2. Slide portions A in the reverse direction to lock. Conductive surface 1-13(E) CA-702 CA-702P...
3. Lift the CN-1528 board up and disconnect the connector CN9 on the CN-1528 board from the connector CN7 on the MB-766 board. 4. Install a new CN-1528 board in the reverse order of removal. MB-766 board CN-1528 board B2 x 4 B2 x 4 B2 x 4 1-14(E) CA-702 CA-702P...
4. Remove the four plug-in boards. 5. Remove the PWB guide(lower). 6. Disconnect the harness connected to connectors CN22 through CN25 on the PS-501 board. 7. Remove the two screws. PWD guide (lower) PS-501 board CN22 CN25 CN24 CN23 P2.6 x 6 1-15(E) CA-702 CA-702P...
Page 24
9. Install a new PS-501 board in the reverse order of removal. B2 x 4 B2 x 4 PS-501 board PS501 bracket Notes on installing When installing, take care that the harness is not caught between the chassis and the board or PWB guide(lower). 1-16(E) CA-702 CA-702P...
When fastening the V shoe to the main chassis, be sure to adjust the mounting position with precisely.The mounting position of the V shoe on the CA-702/P affects the connected position of the DVW-700/ 700WS/700P/700WSP, DNV-5 or DNW-7/90/90WS/7P/90P/90WSP.Be sure to tighten the three screws in order of 1 to 3 as shown in the figure.
The coaxial cable (extension) is available as a replacement part. If broken, replace the cable with a new one. Coaxial cable (extension) : Sony P/N 1-783-252-11 Extension board DIF-67 board...
1-11. Recommended Replacement Part 1-11. Recommended Replacement Part Parts listed below are recommended replacement parts.They are subject to cracks with the lapse of time. Check sometimes by visual, and replace as necessary. Description Sony Part No. TUBE, SHIELD 3-190-628-01 RUBBER(SLIDE), DROP PROTECTION 3-612-447-01...
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
2-1. Preparation 2-1-3. Connection 2-1-3. Connection VCO Adjustment Frequency Oscilloscope counter Probe Video Adjustment 1.5" VF DNW-7 Series CA-702/702P AC ADAPTOR AC-550/550CE DC IN ENG/EFP LENS Video signal generator VIDEO/SDI IN VIDEO/SDI OUT Waveform/Vector monitor Color monitor DA Adjustment 1.5" VF...
Set the POWER switch of CA to ON. And set the POWER switch of Camcorder to ON. Adjustment Procedure Equipment: Digital Voltmeter Setting: DC range Test Point: TP1/RE-153, GND: E2/RE-153 Adjustment Point: 1RV1 (+5V ADJ) / RE-153 +5.0 ± 0.01 V Specifications: RE-153 BOARD (B SIDE) 2-3 (E) CA-702 CA-702P...
Adjustment point: Specifications: NTSC B = A ± 1 IRE B = A ± 1 mV (for PAL) B = A ±1 IRE B = A ±1 mV (NTSC Setup 7.5%) (PAL) TP102 DIF-67 BOARD (A SIDE) 2-6 (E) CA-702 CA-702P...
2-4. AD-150/P Board Adjustment 2-4-4. Analog Composite A/D Level Adjustment (J mode) 2-4-4. Analog Composite A/D Level Adjustment (J mode) The CA-702 needs the following adjustment to maintain its performance. The CA-702P, however, does not need. Preparations 1. Connect each equipment referring to 2-1-3, “Connection - AD Adjustment.”...
Page 40
Specifications: Note in Finishing Adjustment . S102-2/RE-153 (UC/J mode inversion) 8 OFF . S1/AD-150 (AGC) 8 ON RV12 RV12 RV11 RV10 RV11 RV10 RV6 RV7 RV13 Suffix -12 or higher Suffix -11 AD-150 BOARD (A SIDE) 2-12 (E) CA-702 CA-702P...
E = 1400 ± 20 mV E = 1050 ± 20 mV Notes in Finishing Adjustment . S102-1/RE-153 8 OFF S102 S101 TP101 TP108 TP102 TP103 TP105 TP107 E101 TP104 TP106 DA-130/P BOARD (A SIDE) RE-153 BOARD (A SIDE) 2-15 (E) CA-702 CA-702P...
Page 45
3-612-437-01 o GUIDE(UPPER),PWB 3-729-076-11 s SCREW +B 2X4 3-612-438-01 o GUIDE(LOWER),PWB 3-612-444-01 s TYPE1, PRECISION +P2.6X6 7-627-556-78 s SCREW PRECISION +P 2.6X6 TYPE 1 3-612-656-01 o SHEET(40P) 7-682-558-09 s SCREW +B 4X4 7-685-534-19 s SCREW +BTP 2.6X8 TYPE2 N-S CA-702 CA-702P...
Page 46
PLUG-IN BOARDS Part No. SP Description Part No. SP Description A-8317-805-A o MOUNTED CIRCUIT BOARD, AD-150 (for CA-702) 3-612-435-01 o PLATE(DA),ORNAMENTAL A-8317-809-A o MOUNTED CIRCUIT BOARD, AD-150/P(for CA-702P) 3-612-436-01 o PLATE(DIF),ORNAMENTAL A-8317-806-A o MOUNTED CIRCUIT BOARD, DA-130 (for CA-702) 3-612-448-01 o PLATE(RE),ORNAMENTAL...
Page 47
3-604-795-01 s CAP BNC 3-612-447-01 o RUBBER(SLIDE),DROP PRPTECTION 3-676-244-00 s COVER, SWITCH 3-724-728-01 s KNOB (DL), SW 3-729-044-01 s SHEET, SLIDE 3-729-076-11 s SCREW +B 2X4 3-742-074-01 s SCREW +B 3X6 3-849-405-00 s COVER, EARPHONE JACK 7-682-548-09 s SCREW +B 3X8 CA-702 CA-702P...
Page 48
3-742-074-01 s SCREW +B 3X6 3-603-680-01 s STAINLESS SCREW +B3X12 4-887-429-00 s SPACER 3-603-733-01 s HOLDER,SCREW 7-627-553-38 s SCREW,PRECISION +P 3-612-441-01 o SUPPORT,PWB 7-627-556-38 s SCREW +P 2.6X4.0 3-612-444-01 s TYPE1, PRECISION +P2.6X6 3-679-648-02 o SPRING,COMPRESSION 3-679-669-05 o SPACER 3-679-688-02 o LEVER,RELEASE CA-702 CA-702P...
Page 49
Q'ty Part No. SP Description A-8317-805-A o MOUNTED CIRCUIT BOARD, AD-150 C143 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V (for CA-702) C144 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V A-8317-809-A o MOUNTED CIRCUIT BOARD, AD-150P C145 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V...
Page 50
1-162-915-11 s CERAMIC, CHIP 10PF 50V C210 1-162-917-11 s CERAMIC, CHIP 15PF 5% 50V C271 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V (for CA-702) C272 1-115-581-11 s TANTALUM, CHIP 100uF 20% 16V 1-162-919-11 s CERAMIC, CHIP 22PF 5% 50V (for CA-702P)
Page 51
8-759-080-06 s IC TC74VHC574FS(EL) 8-719-820-41 s DIODE 1SS302 IC47 8-759-079-61 s IC TC74VHC74FS(EL) 8-719-820-41 s DIODE 1SS302 IC48 8-759-271-86 s IC TC7SH04FU (for CA-702) IC49 8-759-079-46 s IC TC74VHC00FS(EL) 1-234-091-11 s FILTER, LOW-PASS IC50 8-759-488-29 s IC TC7W66FU(TE12R) 1-233-739-11 s FILTER, LOW-PASS...
Page 52
8-759-271-86 s IC TC7SH04FU IC74 8-759-196-96 s IC TC7SH08FU-TE85R 1-218-672-11 s METAL, CHIP 150 0.5% 1/16W IC75 8-759-196-93 s IC TC7SH00FU-TE85R (for CA-702) 1-218-676-11 s METAL, CHIP 220 0.5% 1/16W IC76 8-759-271-86 s IC TC7SH04FU (for CA-702P) IC77 8-759-196-93 s IC TC7SH00FU-TE85R 1-218-696-11 s METAL, CHIP 1.5K 0.5% 1/16W...
Page 53
1-218-660-91 s METAL, CHIP 47 0.5% 1/16W R175 1-218-694-11 s METAL, CHIP 1.2K 0.5% 1/16W R109 1-218-722-11 s METAL, CHIP 18K 0.5% 1/16W (for CA-702) R110 1-218-724-11 s METAL, CHIP 22K 0.5% 1/16W 1-218-690-11 s METAL, CHIP 820 0.5% 1/16W R111 1-218-724-11 s METAL, CHIP 22K 0.5% 1/16W...
Page 54
1-218-716-11 s METAL, CHIP 10K 0.5% 1/16W R234 1-218-692-11 s METAL, CHIP 1K 0.5% 1/16W R306 1-218-652-11 s METAL, CHIP 22 0.5% 1/16W (for CA-702) R307 1-218-704-11 s METAL, CHIP 3.3K 0.50% 1/16W R235 1-218-676-11 s METAL, CHIP 220 0.5% 1/16W R308 1-218-698-11 s METAL, CHIP 1.8K 0.50% 1/16W...
Page 55
1-218-668-11 s METAL, CHIP 100 0.5% 1/16W R400 1-218-700-11 s METAL, CHIP 2.2K 0.5% 1/16W R452 1-218-668-11 s METAL, CHIP 100 0.5% 1/16W (for CA-702) R401 1-218-692-11 s METAL, CHIP 1K 0.5% 1/16W R453 1-218-668-11 s METAL, CHIP 100 0.5% 1/16W R402 1-218-716-11 s METAL, CHIP 10K 0.5% 1/16W...
Page 56
1-239-412-11 s NETWORK RESISTOR, CHIP 100 1-239-412-11 s NETWORK RESISTOR, CHIP 100 1-237-032-11 s RES, ADJ METAL 500 1-237-036-11 s RES, ADJ METAL 10K (for CA-702) 1-237-036-11 s RES, ADJ METAL 10K (for CA-702) 1-237-035-11 s RES, ADJ METAL 5K (for CA-702P)
1-239-895-11 s FILTER, CHIP EMI 1-572-328-11 s SWITCH, DIGITAL 1-239-895-11 s FILTER, CHIP EMI 1-239-895-11 s FILTER, CHIP EMI 1-239-895-11 s FILTER, CHIP EMI 1-239-895-11 s FILTER, CHIP EMI 1-234-011-21 s FILTER, EMI FL10 1-239-895-11 s FILTER, CHIP EMI 3-13 CA-702 CA-702P...
Page 58
Q'ty Part No. SP Description 1-668-756-11 o PRINTED WIRING BOARD, CN-1529 A-8317-806-A o MOUNTED CIRCUIT BOARD, DA-130 (for CA-702) 1-164-695-11 s CERAMIC 0.0022uF 5% 50V A-8317-810-A o MOUNTED CIRCUIT BOARD, DA-130P 1-164-695-11 s CERAMIC 0.0022uF 5% 50V (for CA-702P) 1-164-695-11 s CERAMIC 0.0022uF 5% 50V...
Page 59
1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C407 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C143 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C408 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C150 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C409 1-113-994-11 s TANTALUM, CHIP 6.8uF 20% 16V 3-15 CA-702 CA-702P...
Page 60
1-234-063-11 s FILTER, LOW-PASS IC53 8-759-079-63 s IC TC74VHC86FS(EL) 1-234-063-11 s FILTER, LOW-PASS IC54 8-752-386-51 s IC CXD3122R 1-234-060-11 s FILTER, LOW-PASS (for CA-702) IC55 8-759-389-26 s IC 74LCX08MTCX 1-234-061-11 s FILTER, LOW-PASS (for CA-702P) IC56 8-752-386-51 s IC CXD3122R...
Page 61
1-218-740-11 s METAL, CHIP 100K 0.5% 1/16W 8-729-028-91 s TRANSISTOR DTA144EUA-T106 1-218-724-11 s METAL, CHIP 22K 0.5% 1/16W (for CA-702) 1-218-676-11 s METAL, CHIP 220 0.50% 1/16W 1-218-716-11 s METAL, CHIP 10K 0.5% 1/16W 1-218-652-11 s METAL, CHIP 22 0.5% 1/16W (for CA-702P) 1-218-686-11 s METAL, CHIP 560 0.5% 1/16W...
Page 62
1-218-740-11 s METAL, CHIP 100K 0.5% 1/16W R178 1-218-676-11 s METAL, CHIP 220 0.5% 1/16W R320 1-216-864-11 s METAL, CHIP 0 5% 1/16W R179 1-218-672-11 s METAL, CHIP 150 0.5% 1/16W R322 1-218-660-91 s METAL, CHIP 47 0.5% 1/16W 3-18 CA-702 CA-702P...
Page 63
1-237-035-11 s RES, ADJ METAL 5K 1-237-033-11 s RES, ADJ METAL 1K R346 1-218-740-11 s METAL, CHIP 100K 0.5% 1/16W 1-237-037-11 s RES, ADJ METAL 20K (for CA-702) R400 1-218-660-91 s METAL, CHIP 47 0.5% 1/16W 1-237-036-11 s RES, ADJ METAL 10K (for CA-702P) R401 1-218-660-91 s METAL, CHIP 47 0.5% 1/16W...
1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V 1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V 1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V 1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V 1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V 1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V 3-20 CA-702 CA-702P...
Page 65
1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V C130 1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V C300 1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V C131 1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V C301 1-107-826-11 s CERAMIC, CHIP 0.1uF 10% 16V 3-21 CA-702 CA-702P...
Page 66
8-759-079-60 s IC TC74VHC32FS(EL) 8-729-117-73 s TRANSISTOR 2SC4178-F14 IC36 8-759-079-49 s IC TC74VHC04FS(EL) 8-729-140-63 s TRANSISTOR 2SA1611-M5M6 IC37 8-759-079-52 s IC TC74VHC08FS(EL) 8-729-029-14 s TRANSISTOR DTC144EUA-T106 IC38 8-759-172-72 s IC CXD8386AQ IC39 8-759-080-06 s IC TC74VHC574FS(EL) 8-729-105-68 s TRANSISTOR 2SC3356-K 3-22 CA-702 CA-702P...
Page 67
1-218-716-11 s METAL, CHIP 10K 0.5% 1/16W 1-218-716-11 s METAL, CHIP 10K 0.5% 1/16W R128 1-218-678-11 s METAL, CHIP 270 0.5% 1/16W 1-218-716-11 s METAL, CHIP 10K 0.5% 1/16W R129 1-218-678-11 s METAL, CHIP 270 0.5% 1/16W 3-23 CA-702 CA-702P...
Page 68
RB38 1-239-416-11 s NETWORK RESISTOR, CHIP 220 R211 1-216-864-11 s METAL, CHIP 0 5% 1/16W RB39 1-239-416-11 s NETWORK RESISTOR, CHIP 220 R214 1-216-864-11 s METAL, CHIP 0 5% 1/16W RB40 1-239-416-11 s NETWORK RESISTOR, CHIP 220 3-24 CA-702 CA-702P...
1-164-156-11 s CERAMIC, CHIP 0.1uF 25V 8-719-938-75 s DIODE SB05-05CP 1-127-512-00 s ELECT 10uF 20% 25V 8-719-067-86 s DIODE ECL06B03-TE16F 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V 8-719-938-75 s DIODE SB05-05CP 1-117-372-11 s TANTALUM, CHIP 100uF 20% 10V 8-719-938-75 s DIODE SB05-05CP 3-27 CA-702 CA-702P...
Page 72
1-218-724-11 s METAL, CHIP 22K 0.5% 1/16W 1-218-732-11 s METAL, CHIP 47K 0.5% 1/16W 8-729-043-17 s TRANSISTOR MTD20P03HDLT4 1-218-726-11 s METAL, CHIP 27K 0.5% 1/16W 8-729-029-14 s TRANSISTOR DTC144EUA-T106 1-218-732-11 s METAL, CHIP 47K 0.5% 1/16W 8-729-028-91 s TRANSISTOR DTA144EUA-T106 3-28 CA-702 CA-702P...
Page 73
1-218-716-11 s METAL, CHIP 10K 0.5% 1/16W 1-218-732-11 s METAL, CHIP 47K 0.5% 1/16W R229 1-218-708-11 s METAL, CHIP 4.7K 0.50% 1/16W 1-218-738-11 s METAL, CHIP 82K 0.5% 1/16W R230 1-218-700-11 s METAL, CHIP 2.2K 0.5% 1/16W 3-29 CA-702 CA-702P...
Page 74
1-218-748-11 s METAL, CHIP 220K 0.50% 1/16W R293 1-218-748-11 s METAL, CHIP 220K 0.50% 1/16W R294 1-218-748-11 s METAL, CHIP 220K 0.50% 1/16W R295 1-218-748-11 s METAL, CHIP 220K 0.50% 1/16W R296 1-218-692-11 s METAL, CHIP 1K 0.5% 1/16W 3-30 CA-702 CA-702P...
Page 75
BNC IN (CN8) 1-784-240-11 s CONVERTER, COAXIAL CONNECTOR BNC OUT -- CN3/DIF 1-783-251-11 s CABLE ASSEMBLY, COAXIAL, RED BNC IN -- CN4/DIF 1-783-252-11 s CABLE ASSEMBLY, COAXIAL, GREEN CN30/DU -- CN2/DIF 1-783-253-11 s CABLE ASSEMBLY, COAXIAL, BLUE 3-31 CA-702 CA-702P...
3-3. Changed Parts NOTE: The numbers identified by marking with ) are 711) Serial No. 10016-(CA-702), 40011-(CA-702P) matching with each serial numbers. 712) Serial No. 10016-10170(CA-702), See the table matched with each serial numbers. 40011-40045(CA-702P) 801) Serial No. 10046-(CA-702), 40011-(CA-702P) 805) Serial No.
Page 77
---> 1-237-035-11 s RES, ADJ METAL 5K 805) C9 1-162-918-11 s CERAMIC, CHIP 18PF 5% 50V ---> 1-162-915-11 s CERAMIC, CHIP 10PF 50V 805) R1 1-218-680-11 s METAL, CHIP 330 0.50% 1/16W ---> 1-218-676-11 s METAL, CHIP 220 0.5% 1/16W 3-33 CA-702 CA-702P...
Page 85
CXD2310AR-T4 (SONY) CXD3122R (SONY) C-MOS DIGITAL LINE MEMORY C-MOS 10-BIT 20 MSPS VIDEO A/D CONVERTER —TOP VIEW— —TOP VIEW— DIN0 DOT0 DIN1 DOT1 DIN2 DOT2 DIN3 DOT3 DOT4 DIN4 TSTR COURSE DIN5 DOT5 CONPARATE DIN6 DOT6 & ENCODE DIN7 DOT7 DD ( +3.0 to +5.5 V )
Page 86
CXD8280AQ (SONY) M62352GP (MITSUBISHI)FLAT PACKAGE M62352GP-75ED C-MOS DIGITAL AUDIO TIME BASE EXPANSION FOR SIF RECEIVER —TOP VIEW— C-MOS 8-BIT x 12 CHANNEL D/A CONVERTER (WITH BUFFER OPERATIONAL AMPLIFIER) —TOP VIEW— DD(+5V) AO10 AO11 AO12 DD(+5V) DD(+5V) AO12 AO10 AO11 (+5V) AO1 - AO12 ;...
Page 87
CXD8281Q (SONY) C-MOS DIGITAL AUDIO TIME BASE COMPRESSION FOR SIF TRANSMITER —TOP VIEW— INPUT (WITH PULL-DOWN REGISTER) 128CK ; DIGITAL AUDIO 128 x Fs CLOCK AD1/2 ; DIGITAL AUDIO CH-1/2 DATA AD3/4 ; DIGITAL AUDIO CH-3/4 DATA ; DIGITAL AUDIO BIT CLOCK (=64 x Fs) C1/2 ;...
Page 88
CXD8385Q (SONY) C-MOS ENCODER —TOP VIEW— INPUT PERROR1 ANC0 - ANC9 ANCILLARY DATA PERROR2 ANIS ANC GATE CONTROL XZLD POUT CF1/CF2 CF DATA MUD0 CFINFO CFINFO CONTROL MUD1 CK27 27 MH CLOCK MUD2 COMP COMPOSIT/COMPONENT MUD3 D1/J2, SLNP MODE CONTROL...
Page 92
TIMER PULSE AD12 (x 2 CHANNEL) UNIT AD11 PROGRAMMABLE AD10 WATCH-DOG TIMING PATTERN TIMER CONTROLLER PORT B PERIPHERAL ADDRESS BUS (24-BIT) PERIPHERAL DATA BUS (16-BIT) INTERNAL ADDRESS BUS (24-BIT) INTERNAL UPPER DATA (16-BIT) INTERNAL LOWER DATA (16-BIT) 4-14 CA-702 CA-702P...
Page 93
M5219/M5220 TYPES +5 to +22.5V _5 to _22.5V MC33077DR2 +2.5 to +18V _2.5 to _18V NJM2100 TYPE +1 to +3.5V _1 to _3.5V OP-297 TYPE +2 to +20V _2 to _20V OTHERS +5 to +16V _5 to _16V 4-15 CA-702 CA-702P...
Page 94
(SCALE 3/1) —TOP VIEW— 10A1 10B1 OPEN DD(+3 to +18V) 10A2 10B2 11A1 11B1 11A2 11B2 GND 4 12A1 12B1 12A2 12B2 CONT.INPUT CHANNEL 0 ; LOW LEVEL 1 ; HIGH LEVEL OPEN X ; DON'T CARE 4-16 CA-702 CA-702P...
Page 95
NON-RETRIGGERABLE M. M. V IN/OUT IN/OUT IN/OUT IN/OUT OPEN IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT OPEN CONTROL "ON" INPUTS = +3 to +12V EE* ; DD - CHANNEL ; LOW LEVEL ; HIGH LEVEL OPEN ; DON'T CARE 4-17 CA-702 CA-702P...
Page 96
+2.7 to +3.6V OTHER TYPES +2 to +6V INPUTS OUTPUTS ; LOW LEVEL ; HIGH LEVEL ; DON'T CARE OUTPUT PULSE WIDTH = 0.7CR NOTE: TYPE +2 to +5.5V 74AC/74VHC 74HCT +4.5 to +5.5V 74HC +2 to +6V 4-18 CA-702 CA-702P...
Page 97
; LEVEL OF QA-QH BEFORE THE INDICATED INPUT CONDITIONS WERE ESTABLISHED ; LOW LEVEL ; HIGH LEVEL ; DON'T CARE NOTE: TYPE 74HCT/74ACT +4.5 to +5.5V 74LVC +2.7 to +3.6V +2 to +5.5V 74AC/74VHC +2 to +6V OTHERS 4-19 CA-702 CA-702P...
Page 98
GND 3 NC 1 Y = A (+2 to +6V) GND 3 0 ; LOW LEVEL 1 ; HIGH LEVEL ; LOW LEVEL TYPE ; HIGH LEVEL 4S01F +3 to +18V 7S02F 7S02FU +2 to +6V 7SH02FU 4-20 CA-702 CA-702P...
Page 99
V REF GND 4 (SCALE 3/1) TYPE INPUTS OUTPUTS FUNCTION 7W74F Qn+1 Qn+1 +2 to +6V 7W74FU CLEAR 7WH74FU +2 to +5.5V SENSE PRESET – – – NO CHANGE ; LOW LEVEL ; HIGH LEVEL ; DON'T CARE 4-21 CA-702 CA-702P...
Page 103
V RESET OUT INPUT MODE/OUTPUT MODE SOFT START +3.5V +3.5V REG CONTROL CIRCUIT VTR S/S OUT POWER SW H: POOL FEED ON/OFF VTR SAVE OUT REC TALLY OUT MODE SW BATT OUT (TO CAMCODER) Overall DC OUT LOT NO. 709- CA-702 CA-702P...
Page 104
RE-153 RE-153 Block Diagram Block Diagram CA-702 (SY) : S/N 10001 and higher CA-702P (SY) : S/N 40001 and higher IC103 IC108 ( 6/9 ) DATA BUS 20-23 CN-1528,7-12 1-32 REC ALARM IN BUFFER IC104 25-31 ADDRESS IC110 ( 4/7 )
Page 105
AD-150/150P AD-150/150P Block Diagram Block Diagram CA-702 (SY) : S/N 10001 and higher CA-702P (SY) : S/N 40001 and higher IC12, IC3, IC13 PULSE VBS DET 1-33 RE,1-46 GENERATOR Q20, Q21, Q18 Y/C MIX VBS OUT 1-37 LINE RET VBS ( X )
Page 107
DIF-67 DIF-67 Block Diagram Block Diagram CA-702 (SY) : S/N 10001 and higher Q15, Q24, IC78 CA-702P (SY) : S/N 40001 and higher SWITCH IC28 OUTPUT VIDEO GAIN TP102 AD, 1-66/DA, 1-66 1-74 REC DATA 9 AD, 1-65/DA, 1-65 1-73...
Page 108
CN-1528 CN-1528 Block Diagram Block Diagram CA-702 (SY) : S/N 10001 and higher CA-702P (SY) : S/N 40001 and higher CN-1528 CN-1529 DA, 1-23 9-21 MIC (G) DA, 1-23 9-22 MIC (G) MIC (X) 10-7 CCZ, 9 MIC ( X, G ) AMP...
Page 139
UNREG GND BLUE CN20 CN21 UNREG GND UNREG GND BATT OUT TO CCZ UNREG GND CN25 DC OUT(+) GREEN DC OUT(+) DC OUT(-) DC OUT BNC IN DC OUT(-) DIF-67 FRAME WIRING BNC OUT LOT NO. 709- CA-702 6-31 6-31 CA-702P...
Page 141
* B4 R245 C124 * B4 R246 C125 * B4 * B4 R247 * D3 CA-702 (SY) : S/N 10001 and higher RE-153 RE-153 C126 * B4 * B4 - A SIDE - - B SIDE - R252 * E2...
Page 155
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of...