Electrolux ICON E24CM75GSS Technical & Service Manual page 46

C C o o m m p p o o n n e e n n t t T T e e a a r r d d o o w w n n
W W i i r r e e H H a a r r n n e e s s s s R R e e m m o o v v a a l l
In order to access and remove most components in the
control compartment or to remove door assembly, the
wire harness will need to be disconnected from the
components of control compartment.
N N O O T T E E : : For some of the electrical components in control
compartment, the wire harness may not have to be
removed from the right side slot. Use caution when
repositioning the ribbon cables.
To disconnect the wire harness (See Figure 4-4):
1. Remove drip tray, open door and remove control
panel cover.
2. Using a wire cutters, cut tie-down straps in control
compartment securing the wire harness compo-
nents together. Carefully pull wire harness leads
out from the components of control compartment.
3. A plastic grommet secures the wire harness in a
slot on the right side of control compartment.
Using a small flat-bladed screw driver, depress the
retaining clips and push the grommet out of slot.
Carefully lift the wire harness out of slot.
4. Disconnect the two ribbon cables from display and
control panel.
5. Disconnect wire leads from the door microswitch.
6. Disconnect wire leads from power switch. Label to
assure proper re-connection.
7. Disconnect wire leads that go to light switch and
transformer from the "Y" terminals disconnected in
step 6.
T T o o u u c c h h p p a a d d L L E E D D P P o o w w e e r r S S u u p p p p l l y y R R e e m m o o v v a a l l
A ribbon cable runs from the control panel to a 5 pin
connector on the touchpad LED power supply. A pur-
ple and white wire run from the transformer to the wire
terminal mounted on the circuit board.
The outlet of the touchpad LED power supply should
test at 350mA with a max of 24V when power is
applied.
To remove the touchpad LED power supply
(See Figure 4-5):
1. Remove drip tray, open door and remove control
panel cover.
2. Disconnect small ribbon cable from touchpad LED
power supply.
3. Using a small flat-bladed screwdriver, loosen the
setscrews securing wire leads to the touchpad LED
power supply wire terminal.
Disconnect
Here
Light
Switch
Transformer
Power
Switch
Circuit Board
F F i i g g u u r r e e 4 4 - - 4 4 . . W W i i r r e e H H a a r r n n e e s s s s R R e e m m o o v v a a l l
N N O O T T E E : : O O n n l l y y t t h h e e w w i i r r i i n n g g n n e e e e d d e e d d t t o o b b e e d d i i s s c c o o n n n n e e c c t t e e d d f f o o r r
w w i i r r e e h h a a r r n n e e s s s s r r e e m m o o v v a a l l i i s s s s h h o o w w n n a a b b o o v v e e . .
Red Stripe
F F i i g g u u r r e e 4 4 - - 5 5 . . T T o o u u c c h h p p a a d d L L E E D D P P o o w w e e r r S S u u p p p p l l y y R R e e m m o o v v a a l l
4-4
Red
Blue
Disconnect
Here
Door
Microswitch
Inlet Voltage
Purple
Ribbon Cable
Disconnect Here
Slot
White