TABle OF CONTeNTS Before You Begin ... 2 Finding Information ... Important Safety Instructions ...4 Safety ... 5 Preparing for Installation ... 7 Planning the Location ...7 IF YOUR UNIT ReQUIReS SeRvICe... IMPORTANT: If the unit requires service, be sure to have the model and serial number available when you call.
Indicates installation, operation or maintenance information which is important but not hazard related. WARNING electrolux cannot be held responsible for damage to property or injury to persons caused by failure to comply with the installation, maintenance and safety instructions contained in this handbook.
WARNING To reduce the risk of fire, electrical shock, or injury when using your coffee maker, follow basic safety precautions including the following: Read all instructions before operating the coffee maker. IMPORTANT: Before performing any type of service or installation, make sure that electric power to the coffee maker is disconnected.
Safety General Safety Precautions (continued) WARNING • Do not tamper with the controls. • Clean the coffee maker thoroughly according to the Flushing Out the Coffee Maker section in the use and care guide before operating it for the first time. •...
It is located in the lower right rear corner on the back of the unit. It must be plugged directly into a dedicated, wall-mounted electrical receptacle. • The electrical outlet (and water shut off valve for model E24CM76GSS) should be located in an adjacent cabinet. Both must be accessible when the unit is installed.
See the table below. • Do not install any appliance above or below the the coffee maker. Overhanging cabinet Model E24CM75GSS E24CM76GSS Install unit low enough for easy access to coffee bins on top Veritical distance to overhang Coffee maker pulled...
Power Cord Length Unit Weight Shipping Weight Fresh Water Capacity (Model E24CM75GSS) Minimum Input Water Pressure (Model E24CM76GSS) Maximum Input Water Pressure (Model E24CM76GSS) Water inlet diameter (Model E24CM76GSS) The correct voltage, frequency and amperage must be supplied to the electrical outlet from a grounded, dedicated, single phase circuit that is protected by a properly sized circuit breaker or time-delay fuse.
Steam barrier with mounting screws • 2 guide assemblies with mounting screws • 6” metal shims, 1/16” (1mm) • Three foot 1/4” to 3/4” flexible water supply hose(E24CM76GSS) • Use & care guide • Detergent tablets (sample) • Spare tank O-ring (model E24CM75GSS) •...
TOOlS NeeDeD FOR INSTAllATION • Phillips screwdriver • Measuring tape • Level • Drill with 1/16” drill bit STeAM BARRIeR INSTAllATION • Position the steam barrier inside the top of the cut-out. Push it towards the back wall until the back edge lines up with the back of the cabinet. •...
The coffee maker requires periodic decalcification that must be performed regardless of the water hardness level. The filter head in the kit is required to perform this process for model E24CM76GSS. Decalcification will be MUCH SIMPLER with the Electrolux ACCFILT-24 filter system already installed. In addition, the filter will improve water taste.
Installation To house water supply To coffee maker Filter head everpure Filter Cartridge electrolux ACCFIlT-24 Filter Kit with Filter Installed...
Installation InstallIng the CabInet glIdes The cabinet glides mount to the inside of the cabinet. The glides on the coffee maker slide into the cabinet glides. The guide system allows the coffee maker to slide in and out of the cabinet for loading the coffee bins and for maintenance.
• Put the two (2) cabinet glide assemblies, and shims if necessary, as shown on the inside surfaces of the cabinet. Position them 3 1/2” (9.0cm) from the front edge of the cutout opening. • Insert the screws in the holes of the glides without tightening them completely.
Installation INSTAllING THe UNIT IN THe CABINeT • While supporting the coffee maker from below, insert it into the cabinet cutout. As you insert it into the cabinet, line up the glides on the appliance with the cabinet glides. The appliance should glide on the rails when slight pressure is applied to the front of the coffee maker.
CONNeCTING THe PlUMBING (e24CM76GSS) WARNING • To prevent damage to the coffee system due to hard water, prior to installation, check the water hardness for the building where you will be installing the coffee maker. See page 12 • To avoid leaks, do not overtighten fittings.
Turn on the power switch. It is located near the middle of the brewing compartment ceiling. • On model E24CM76GSS (plumbed model): Turn on the water supply at the shut-off valve. Check the water lines for leaks. • On model E24CM75GSS (tank model): Fill the tank with filtered water (4 gpg maximum water hardness, do not use distilled water).
Troubleshooting (Continued) Check the Solutions to Common Problems section of the use and care guide. Repeat the verification process. If the appliance still does not work, contact an authorized Electrolux at the phone number inside the front cover. INSTAllATION CHeCKlIST WARNING •...