Related Manuals for Titan TTB285JSW
Summary of Contents for Titan TTB285JSW
- Page 1 100816_TTB285JSW_Jig Saw-EN-08.pdf 8/16/10 2:04 PM SAFETY AND OPERATING MANUAL Original instructions JIG SAW 750W TTB285JSW...
- Page 2 2:04 PM Congratulations on your purchase of a power tool from Titan Power Tools (UK) Ltd. We want you to continue getting the best performance from it so this handbook includes information on safety, handling and care. Please retain this handbook in case you need to refer to any of the information in the future.
-
Page 3: General Safety Instructions
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. JIG SAW 750W TTB285JSW... - Page 4 100816_TTB285JSW_Jig Saw-EN-08.pdf 8/16/10 2:04 PM d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
- Page 5 6. Do not change the laser device with a different type. Repairs must be carried out by the manufacturer or an authorised agent. CAUTION! Use of controls or adjustments other than those specified herein may result in hazardous radiation exposure. JIG SAW 750W TTB285JSW...
- Page 6 100816_TTB285JSW_Jig Saw-EN-08.pdf 8/16/10 2:04 PM VIBRATION The European Physical Agents (Vibration) Directive has been brought in to help reduce hand arm vibration syndrome injuries to power tool users. The directive requires power tool manufacturers and suppliers to provide indicative vibration test results to enable users to make informed decisions as to the period of time a power tool can be used safely on a daily basis and the choice of tool.
-
Page 7: Double Insulation
Be sure the supply is the same as the voltage given on the rating plate. The tool is fitted with a two-core cable and plug. Always remove the mains plug from socket before carrying out any adjustment or servic- ing. JIG SAW 750W TTB285JSW... - Page 8 100816_TTB285JSW_Jig Saw-EN-08.pdf 8/16/10 2:04 PM SYMBOLS To reduce the risk of injury, user must read instruction manual Warning Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
- Page 9 Variable speed control wheel Laser/LED light on/off switch Laser generator/LED light Wire frame safety guard Blade holder Parallel guide fixture Parallel guide 10 Saw Blade 11 Guide roller 12 Pendulum action switch 13 Vacuum/Blower selector 14 Dust extraction adaptor JIG SAW 750W TTB285JSW...
-
Page 10: Technical Data
100816_TTB285JSW_Jig Saw-EN-08.pdf 8/16/10 2:04 PM TECHNICAL DATA Voltage: 230-240V~ 50Hz Input power: 750W 800-3000/min No load speed: Blade types: ”T” and “U” shank Maximum cutting depth: 100mm (wood) 20mm (aluminium) 10mm (steel) Protection class: Machine weight: 2.7kg LASER INFORMATION Class 2 Laser class: Wavelength: 650nm... -
Page 11: Intended Use
To remove blade, hold the blade and push the ring then lift out the blade. Warning: Blade teeth are very sharp. For best cutting result , ensure you use a blade suited to the material and cut quality you need. JIG SAW 750W TTB285JSW... - Page 12 100816_TTB285JSW_Jig Saw-EN-08.pdf 8/16/10 2:04 PM 2. Using the parallel guide (Fig. 2) Parallel guide can be used for making cuts parallel to a work piece edge at a chosen distance. Slide the parallel guide arm through the slot and tighten the screw (8) to lock it into position.
- Page 13 Use low pendulum action when working with hard materials such as steel. Use high pendulum action when working with most soft materials such as wood and plastic. The optimum setting can be determined in practical trials on scrap material. JIG SAW 750W TTB285JSW...
-
Page 14: Cutting Metal
100816_TTB285JSW_Jig Saw-EN-08.pdf 8/16/10 2:04 PM 7. Speed selection (Fig. 7) With the thumbwheel, the required speed rate can be selected (also while running). MIN-1 = Low speed rate: for metals other than aluminium 2-4 = Medium speed rate: for aluminum and PVC 5-MAX = High speed rate: for wood The speed rate required depends upon the material and the working conditions: fast enough to make... - Page 15 Switch off the laser when you stop the machine. The laser does not switch off automatically. Caution: Switch off the laser when stop the machine. Never stare directly into the laser beam and never point the beam at anybody. JIG SAW 750W TTB285JSW...
-
Page 16: Working Hints For Your Jig Saw
100816_TTB285JSW_Jig Saw-EN-08.pdf 8/16/10 2:04 PM Working hints for your Jig saw 1. Here is some advice on the pendulum action control: the saw blade is only pressed against the material on the return stroke/working stroke. It is moved away from the material on the forward stroke. - Page 17 L. A 13AMP (BS1363 or BS1363/A) plug must be used and a 13 AMP fuse must be fitted. 13 AMP BLUE FUSE N (NEUTRAL) BROWN L (LIVE) OUTER SLEEVE CABLE GRIP JIG SAW 750W TTB285JSW...
-
Page 18: Declaration Of Conformity
EN 55014-1: 2006+A1: 2009 EN 55014-2:1997+A1: 2001+A2: 2008 EN 61000-3-2: 2006 EN 61000-3-3: 2008 Authorised Signatory and technical file holder Date: 28/06/2010 Signature:________________ Name / title: Peter Harries / Quality Manager Titan Power Tools (UK)Ltd. Trade House , Mead Avenue ,BA22 8RT...