Page 1
33 cm 5 in 1 Backpack Multi Tool TT5MTP33BP-2 EAN: 5059340256108 BX220IM/B3 WARNING: Read the instruction handbook thoroughly before using the machine. First time operators should receive practical use instructions of the machine and protective equipment from an experienced operator.
TT5MTP33BP-2 Let’s get started... These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. Getting Started... Safety information Technical specifications Your 5-in-1 Multi tool Before start Quick start detail... more Machine...
Safety information TT5MTP33BP-2 Safety warnings IMPORTANT READ CAREFULLY BEFORE USE KEEP FOR FUTURE REFERENCE > This machine is not intended for use by children and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. >...
Page 4
Safety information TT5MTP33BP-2 > Do not under any circumstances modify the machine. Modifications can result in serious personal injury or death. > Servicing and maintenance, other than listed in this manual, should be performed by an authorised service centre. >...
Page 5
Safety information TT5MTP33BP-2 > Keep handles dry, clean and free from oil and grease. Greasy, oily handles are slippery and may cause loss of control. Do not operate the machine with one hand! Serious injury to the operator or bystanders may result from one handed operation.
Page 6
Safety information TT5MTP33BP-2 > extending the cutter line always return the machine to its normal operating position before switching on. > If the cutting mechanism does not stop when the engine idles, switch the engine off and stop using the machine. Then contact the authorised service centre.
Page 7
Safety information TT5MTP33BP-2 > Disconnect the spark plug connector before performing maintenance, except for carburetor adjustments. > Keep the engine and petrol storage area free of grass, thatch, moss, leaves or excessive grease to reduce the fire hazard. > Examine the machine before each use and replace worn or damaged parts.
Page 8
Safety information TT5MTP33BP-2 > If you have spilt fuel on yourself or on your clothes, change your clothes and wash any part of your body that has come in contact with fuel before turning the engine on again. > If fuel has ignited, put out the fire with a dry powder fire extinguisher.
Page 9
Safety information TT5MTP33BP-2 Emergency Familiarise yourself with the use of this machine by means of this instruction manual. Memorise the safety directions and follow them to the letter. This will help to prevent risks and hazards. > Always be alert when using this machine, so that you can recognise and handle risks early.
Page 10
Safety information TT5MTP33BP-2 Symbols On the machine, the rating label and within these instructions you will find among others the following symbols and abbreviations. Familiarise yourself with them to reduce hazards like personal injuries and damage to property. Kilowatt Litre...
Page 11
Safety information TT5MTP33BP-2 Wear hearing/ear protection (compliant to EN 352-1) Wear eye protection (compliant to EN 166) Wear head protection (compliant to EN 397) Wear protective and slip-resistant footwear (compliant to EN ISO 20345 Class 2) Wear protective clothing (compliant to EN ISO 11393-2, EN ISO 13688 Class 1) Stop the engine before refuelling.
Page 12
7300 Safety information TT5MTP33BP-2 Beware of thrown objects. Objects thrown by the machine could hit the operator or other bystanders. Always ensure that other people and pets remain at a safe distance from the machine when it is in operation.
Page 13
The machine complies with the conformity requirements of the applicable UK regulations. Designation of the tool TT5MTP33BP-2 (TT_Brand Name - Titan; 5MT_5 in 1 Multi Tool; P_Petrol Power; 33_Engine Size; BP_Backpack) 5059340256108_5-in-1_tool_backpack_Mac_A5-IM-V01-EN.indd 11-04-2022 17:35:04...
Page 14
TT5MTP33BP-2 ENGINE > Engine type: SL36E, air cooled 2 stroke > Engine displacement: 33 cm (33 cc) Maximum engine power > (in accordance with ISO 8893): 1.0 kW > Maximum operating engine speed (rotational frequency): 10000 min > Idle speed: 2500 min >...
Page 15
TT5MTP33BP-2 Max. cutting width: > Ø430 mm > Maximum rotational frequency 7000 min of the spindle: HEDGE TRIMMER > Weight (empty tank): 11.3 kg Max. cutting length: > 395 mm > Teeth gap: 24 mm Reciprocating speed: > 2500 min >...
Before you start TT5MTP33BP-2 Unpacking 1. Unpack all parts and lay them on a flat, stable surface. 2. Remove all packing materials and protective shipping materials, if applicable. 3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the machine and contact your dealer.
Page 22
Before you start TT5MTP33BP-2 Assembly WARNING! The machine must be fully assembled before operation! Do not use a machine that is only partly assembled or assembled with damaged parts! Follow the assembly instructions step-by-step and use the pictures provided as a visual guide to assemble the machine easily! Disconnect the spark plug connector before assembly! Reconnect it after assembly (see "Maintenance").
Page 23
Before you start TT5MTP33BP-2 Rubber damper 5059340256108_5-in-1_tool_backpack_Mac_A5-IM-V01-EN.indd 23 5059340256108_5-in-1_tool_backpack_Mac_A5-IM-V01-EN.indd 23 11-04-2022 17:35:11 11-04-2022 17:35:11...
Page 24
Before you start TT5MTP33BP-2 (A12) without rubber sleeve. locking pin (Fig. 2). Locking shaft (A12). 5059340256108_5-in-1_tool_backpack_Mac_A5-IM-V01-EN.indd 11-04-2022 17:35:12...
Page 25
Before you start TT5MTP33BP-2 4. Using hex key (F4) unscrew the bolt along with the washers preassembled on the joint clamp (A14). erify (A12) all the way in the joint clamp (A14) (A12) to form a hole for the bolt.
Page 26
Before you start TT5MTP33BP-2 8. Use the throttle cable clips (A25) to secure the throttle cable (A13) to the flexible shaft (A12) (Fig. 4). Assembling the pole pruner attachment CAUTION! Risk of cuts! The teeth of the saw chain (C7) are very sharp! Protective gloves must be worn for all work on the saw chain (C7).
Page 27
Before you start TT5MTP33BP-2 2. Identify the correct saw chain direction. Start to wrap the saw chain (C7) around the guide bar (C6) (Fig. 6). (C7) around drive sprocket (Fig. 7). Drive sprocket Chain tension pin 5059340256108_5-in-1_tool_backpack_Mac_A5-IM-V01-EN.indd 11-04-2022 17:35:14...
Page 28
Before you start TT5MTP33BP-2 carefully place the guide bar (C6) on the chain tension pin (Fig. 8). Drive sprocket (C12) with the spring washer using the multi-tool III (F3). Tensioning the saw chain NOTE: can lengthen considerably. This is normal during the break-in period and the interval between future adjustments will lengthen quickly.
Page 29
Before you start TT5MTP33BP-2 1. Using the multi-tool III (F3), rotate the tension screw clockwise to increase the tension on the saw chain (C7) or anti-clockwise to decrease the tension on the saw chain (C7) (Fig. 9). Tension screw 5059340256108_5-in-1_tool_backpack_Mac_A5-IM-V01-EN.indd...
Page 30
Before you start TT5MTP33BP-2 2. Pull the saw chain (C7) along the top of the guide bar (C6) by hand from one end to the other, several times. The chain should feel tight but still move freely. It should be possible to lift up the saw chain (C7) 3-4 mm from the guide bar (C6) (Fig. 10).
Page 31
Before you start TT5MTP33BP-2 NOTE: Use lubricant oil SAE#10W-30 all year round or SAE#30-#40 in summer Use lubricant oil SAE#10W-30 all year round or SAE#30-#40 in summer and SAE#20 in winter. and SAE#20 in winter. NOTE: Towards the end of the season, it is advisable to put only as much lubricant in the tank as you need for each cut, so that it is completely used up before you store the machine.
Page 32
Before you start TT5MTP33BP-2 3. Rotate the backing flange (D6) until its hole aligns with the one on the gear head (D3) (Fig. 12). 4. Insert the multi-tool II (F2) into the hole to lock the rotation of the backing flange (D6).
Page 33
Before you start TT5MTP33BP-2 Assembling the cutting blade The tri-arc cutting blade (D7) is used together with the cutting-attachment guard (D4) only. Use the tri-arc cutting blade (D7) for cutting heavier weeds, brush and similar vegetation with a thickness of up to 20 mm.
Page 34
Before you start TT5MTP33BP-2 3. Remove the trimming guard (D14) completely (Fig. 17). 4. Using the hex key (F4) loosen the 2 pre-assembled bolts on the cutting- attachment guard (D4). 5. Attach the cutting-attachment guard (D4) onto the plate on the shaft tube (D2).
Page 35
Before you start TT5MTP33BP-2 6. Rotate the backing flange (D6) until its hole aligns with the one on the gear head (D3) (Fig. 19). 7. Insert the multi-tool II (F2) into the hole to lock the rotation of the backing flange (D6).
Page 36
Before you start TT5MTP33BP-2 Assembling the attachment to the drive shaft tube 1. Remove the protective cap (B1/ C1/ D1/ E1) from the attachment to be used. 2. Pull out and rotate the locking knob (A23) on the shaft clamp (A22) anticlockwise to stop at the bracket.
Page 37
Before you start TT5MTP33BP-2 Filling up fuel and oil WARNING! This machine is not supplied with petrol-oil mixture in the engine! This machine is equipped with a 2-stroke engine. The fuel and oil tank are combined WARNING! NOTE: the fuel mixing bottle (F6) and the fuel tank (A8).
Page 38
Before you start TT5MTP33BP-2 NOTE: Use an anti-oxidant added quality oil expressly labelled for air-cooled 2 stroke engine use (JASO FC GRADE OIL or ISO EGC GRADE). Do not use BIA or TWC (2 stroke water-cooling type) mixed oil. The recommended mixing ratio for petrol:oil is 40:1.
Page 39
Before you start TT5MTP33BP-2 Operating controls Stop switch Recoil starter handle Throttle trigger lockout Primer CLOSE OPEN Choke Throttle trigger 5059340256108_5-in-1_tool_backpack_Mac_A5-IM-V01-EN.indd 11-04-2022 17:35:23...
Quick start TT5MTP33BP-2 Preparation 40:1 For pole pruner only: Add Assemble Add fuel and oil mixture chain oil Cold engine Set stop switch to I Set the choke to CLOSE Press primer 6 times position Pull recoil starter handle Set the choke to OPEN...
Page 41
Quick start TT5MTP33BP-2 Warm engine Set stop switch to I Set the choke to OPEN Pull recoil starter handle position until engine starts Press the throttle trigger Operate lockout and throttle trigger, and release them Stopping Set stop switch to STOP...
Intended use This 33 cm 5 in 1 Backpack Multi tool TT5MTP33BP-2 is designated with a maximum power output of 1 kW. With the machine carrying as a backpack, operate with the left hand on the front handle (A20) and with the right hand on the rear handle (A15).
Page 43
Machine functions TT5MTP33BP-2 Safety equipment The machine has several pieces of safety equipment which reduce the risk of injury when working. Cutting-attachment and trimming guard > The guards (D4/ D14) protect the operator against thrown objects during operation. > Use the grass trimmer only together with the trimming guard (D14) and cutting- attachment guard (D4).
Page 44
Machine functions TT5MTP33BP-2 1. Route the shoulder and waist straps of the harness (F5) through the metal rings. Carry the harness (F5) on both shoulders and buckle the shoulder and waist straps (Fig. 25). Metal ring Metal ring 2. Adjust the straps so that the back padding is held firmly and comfortably against the back.
Machine functions / Operation TT5MTP33BP-2 Barrier bar The barrier bar (A21) is intended to maintain a minimum distance at the machine’s side from an obstruction or a wall. Always assemble the front handle (A20) with the barrier bar (A21) to the machine (Fig. 27).
Page 46
Operation TT5MTP33BP-2 9. Do not overwork yourself. Take regular breaks to ensure you can concentrate on the work and have full control over the machine. 10. Understand the purpose and use of all safety equipment, including the harness. NOTE: In some countries regulations define at what time of the day and on what...
Page 47
Operation TT5MTP33BP-2 Starting cold engine the ground or any objects. 2. Set the stop switch (A17) to I position (Fig. 29). 3. Set the choke (A10) to CLOSE position (Fig. 30). 31). 5. Hold the machine securely to the ground. Place...
Page 48
Operation TT5MTP33BP-2 Starting warm engine 1. Place the machine on a flat and stable surface. The attachment should not touch the ground or any objects. 2. Set stop switch (A17) to I position (Fig. 33). 3. Set the choke (A10) to OPEN position (Fig.
Page 49
Operation TT5MTP33BP-2 Brush cutter and grass trimmer use Trimmer line feeding The string trimmer head (D12) is equipped with a bumper to help to feed the cutting line (D13). Tap the bumper on a firm ground while the machine is operating, the spool will release fresh trimming line (Fig.
Page 50
Operation TT5MTP33BP-2 > Do not lift the cutting attachment higher than your knee. The higher you hold the cutting attachment, the higher the risk of objects being thrown (Fig. 36). Max. height: 300 mm > Avoid cutting tall grass in one cut. Trim taller grass in stages (Fig. 37).
Page 51
Operation TT5MTP33BP-2 > Hold the cutting attachment just above the ground at an angle of approximately 30° (Fig. 38). > Move the machine with slow and regular motion from left to right before moving it back to the starting position and trimming the next area (Fig. 39).
Page 52
Operation TT5MTP33BP-2 Pole pruner use Angle adjustment Adjust the attachment angle to suit working conditions. 1. Press the locking lever (C10) down with one hand (Fig. 41). 2. Hold the clutch cover (C11) with the other hand and turn until the desired angle is adjusted (Fig.
Page 53
Operation TT5MTP33BP-2 Kickback WARNING! Beware of kickback! Kickback can lead to dangerous loss of control of the machine and result in serious or fatal injury to the operator or anyone standing close by! Always be alert because rotational kickback and...
Page 54
Operation TT5MTP33BP-2 Pruning > Always hold the machine firmly with both hands on the front handle (A20) and rear handle (A15). Never operate this machine using only one hand (Fig. 43). > Maintain a firm grip with your thumbs and fingers encircling the handles. A firm grip will help you reduce “kickback”...
Page 55
Operation TT5MTP33BP-2 > Never stand on a ladder or other type of unstable support while using the machine. Insecure stand invites hazards (Fig. 47). WARNING! This machine has not been designed to provide protection from electric shock in the event of contact with overhead electric lines! Therefore do not use machine near cable, electric power or telephone lines.
Page 56
NOTE: The chain must be running at full speed before it comes into contact with the wood. Operation TT5MTP33BP-2 Cut thin branches NOTE: The chain must be running at full speed before Thin branches can be cut off with one single cut. To prevent it comes into contact with the wood.
Page 57
Operation TT5MTP33BP-2 Hedge trimmer Angle adjustment Adjust the attachment angle to suit working conditions. 1. Depress the locking levers (B4) with one hand and hold them in position (Fig. 53). 2. Move the shaft tube (B3) with the other hand until the desired angle is adjusted (Fig.
Page 58
Operation TT5MTP33BP-2 Trimming > Cut and remove branches exceeding the cutting capacity of this machine using a suitable pruner before operation. > (A15) and hand grip (B2). Never operate this machine using only one hand. > Cut both sides from the bottom cutting upwards to the top. This will prevent any of the cuttings falling into the path of the area still to be cut (Fig.
Page 59
Operation TT5MTP33BP-2 NOTE: When shaping it is advisable to achieve a trapezoidal shape (Fig. 58). A trapezoidal cut corresponds to the natural growth of plants and results in optimal hedge growth, as it will expose more light to the bottom of the hedge.
Care and maintenance TT5MTP33BP-2 The golden rules for care WARNING! Always stop the engine, disconnect the spark plug connector (A5) and let the engine cool down before performing inspection, maintenance and cleaning work. DANGER! Proper maintenance is essential for safe and trouble free operation.
Page 61
Care and maintenance TT5MTP33BP-2 Cleaning the cutting device (hedge trimmer) > Keep the cutting device (B6) clean and free of debris. Remove trimmings. > Keep the cutter blade (B7) sharp to retain a good cutting performance. Replace a worn or damaged cutting device (B6) with a new one of the same type.
Page 62
> Clear residue from the rails on the guide bar (D7) using a Care and maintenance TT5MTP33BP-2 screwdriver, putty knife, wire brush or other similar tool. This will keep the oil passages open to provide proper lubrication to the guide bar (D7) and saw chain (D6).
Page 63
Ma in te n a n c e a n d R e pa ir s Care and maintenance TT5MTP33BP-2 S a w C ha in S ha rping WA R N IN G ! Only sharpen the saw chain yourself if you...
Page 64
Care and maintenance TT5MTP33BP-2 M4MTP25-2 by M a c A llis te r Ma in te n a n c e a n d R e pa ir s M4MTP25-2 by M a c A llis te r Ma in te n a n c e a n d R e pa ir s >...
Page 65
Care and maintenance TT5MTP33BP-2 Sprocket wheel 1. Clean the sprocket wheel. 2. Using a disposable lube gun, insert the needle nose into the lubrication hole (C8) and inject grease until it appears at the outside edge of the sprocket (Fig. 67).
Page 66
Care and maintenance TT5MTP33BP-2 To replace the cutting line: 1. Take out the old spool and remove the remaining cutting line. 2. Cut a new 4 meter long cutting line with a diameter of 3 mm 3 mm. 3. Form a loop at the middle of the line and insert this loop into the hook on the spool (Fig.
Page 67
Care and maintenance TT5MTP33BP-2 Cover Locking tab compressed air (max. 3 bar) to remove stubborn dust. (A6). > Keep fuel fresh (less than 30 days) or add fuel stabiliser. > Empty the fuel tank after every use. > Run the machine dry of fuel in idle before storage.
Page 68
Care and maintenance TT5MTP33BP-2 Spark plug NOTE: For good performance, the spark plug must be properly gapped and must be free of deposits. Inspect the spark plug every 25 hours of operation or before long-term storage over 30 days. Clean or replace with a new one if necessary.
Page 69
Care and maintenance TT5MTP33BP-2 Carburetor The carburetor has been carefully set at the factory. Adjustment may be necessary if you notice that the engine does not idle (e.g. the cutting attachment keeps moving when the throttle trigger is released). Contact an authorised service centre or dealer to do idle speed adjustment.
Page 70
Care and maintenance TT5MTP33BP-2 Maintenance table Inspect and maintain this machine regularly based on below maintenance table. Keep the machine in good working condition during maintenance. Part Task Before/after Every 10 hours Every 25 hours each use of operation of operation...
Page 71
Care and maintenance TT5MTP33BP-2 Spare parts/Replacement parts WARNING! Risk of injury! Use of non-genuine replacement components can result in serious personal injury or death. The following parts of this machine may be replaced by the consumer. Spare parts are available at an authorised dealer or through our customer service.
Page 72
Care and maintenance TT5MTP33BP-2 Short term storage (less than 1 day) 1. Let the machine cool down before storage. 2. Store the machine as horizontally as possible. Make sure that no fuel-oil mixture can run out of the carburetor. Long term storage NOTE: Risk of machine damage! >...
Troubleshooting TT5MTP33BP-2 Troubleshooting Suspected malfunctions are often due to causes that the operators can fix themselves. Therefore check the machine using this section. In most cases, the problem can be solved quickly. WARNING! Only perform the steps described in these instructions! All further...
Page 74
Troubleshooting TT5MTP33BP-2 Engine does Air filter is soiled? Clean the air filter. not reach Incorrect fuel or incorrect Stop the engine, empty tank, the maximum mixture? then fill up with the correct speed. mixture of fuel to oil (40:1). Carburetor setting not correct? Have a qualified person adjust the carburetor.
Page 75
Troubleshooting TT5MTP33BP-2 Problem Possible cause Solution Excessive Cutting attachment broken? Replace the broken attachment. vibration/ Flanges/nut loosened? Stop the engine and re-tighten noise or the loosened fasteners. smoke. Incorrect fuel or incorrect Stop the engine, empty tank, then mixture? fill up with the correct mixture of fuel to oil (40:1).
Recycling and disposal / Guarantee TT5MTP33BP-2 Recycling and disposal 1. Old machines are potentially recyclable and do not, therefore, belong in your household rubbish. You are requested to assist us and our contribution to saving resources and protecting the environment by handing in this machine to an equipped collection centre (if there is one available).
Customer care and technical helpline TT5MTP33BP-2 Customer care and technical helpline A better way to repair your tools to last. But if a fault develops with your garden power tool and you need to claim under the guarantee, the Customer Care and Technical Helpline can support with technical assistance or if required, arrange a free courier collection from your home, assess your garden power tool for fault, repair it, and return it.
Availability of spare parts TT5MTP33BP-2 Availability of spare parts Contact the customer service helpline for assistance or visit www.kingfisherspares.com For assistance contact the customer services helpline: UK: 0800 0789647 uk@Kingfisherservice.com EIRE: 1800 932226 eire@kingfisherservice.com Further information about this product can also be found at: www.kingfisher.com/products...
UK declaration of conformity TT5MTP33BP-2 (UK) DECLARATION OF CONFORMITY Product > 33cm 5 in 1 Backpack Multi Tool > TT5MTP33BP-2 > 000001 - 999999 Name and address of the manufacturer or his authorised representative: 3 Sheldon Square London W2 6PX United Kingdom This declaration of conformity is issued under the sole responsibility of the manufacturer.
> 5 in 1 Backpack Multi Tool / Outil multifonction à dos 5-en-1 / Plecakowe narzędzie wielofunkcyjne 5 w 1 / Unealtă multifuncțională rucsac 5 în 1 / Multiherramienta 5 en 1 de mochila / 5 em 1 Mochila Multiferramentas > TT5MTP33BP-2 > 33 cm , 1.0kW...
Page 81
EU declaration of conformity TT5MTP33BP-2 2006/42/EC as amended Machinery Directive 2014/30/EU as amended Directive Electromagnetic compatibility 2000/14/EC as amended Outdoor Noise Directive 2016/1628/EU Regulation Gaseous and Particulate Pollutant Emission Limits 2011/65/EU as amended Directive Restriction of the use of certain hazardous substances in electrical...
Page 82
EU declaration of conformity TT5MTP33BP-2 in relation to which conformity is declared: Références des normes harmonisées pertinentes appliquées, y compris la date de celles-ci, ou des autres Odwołania do odnośnych norm zharmonizowanych, które zastosowano, wraz z datą normy, lub do innych...
Page 83
Manufacturer, Fabricant, Prodecent, Producător, Fabricante: UK Manufacturer: Kingfisher International Products Limited 3 Sheldon Square London W2 6PX United Kingdom EU Manufacturer: Kingfisher International Products B.V. Rapenburgerstraat 175E 1011 VM Amsterdam The Netherlands www.diy.com www.screwfix.com www.screwfix.ie To view instruction manuals online, visit www.kingfisher.com/products 5059340256108_5-in-1_tool_backpack_Mac_A5-IM-V01-EN.indd 83 5059340256108_5-in-1_tool_backpack_Mac_A5-IM-V01-EN.indd 83...
Need help?
Do you have a question about the TT5MTP33BP-2 and is the answer not in the manual?
Questions and answers