Table of Contents
Advertisement
Recording time code following the one last recorded on the tape
BR-DV6000 is equipped with a time code reader. When it enters the RECORD mode from the
RECORDING PAUSE mode, it reads the time code data already recorded on the tape and contin-
ues recording time code from that value. (Regeneration)
TC/UB/CLOCK(1/2) Menu screen
–
–
–
T
C
/
U
B
/
C
L
O
C
K
1 (
2 /
T
C
G
S
O
U
R
C
E
I
N
T
C
G
S
E
L
E
C
T
R
E
T
C
G
M
O
D
E
R
E
N
D
/ F
D
F
(
N
T
S
C
)
–
–
D
F
B
T I
(
P
A
) L
O
N
T
C
D
U
P
I L
C
A
T
E
O
F
T
C
O
F
F
S
E
T
O
F
N
E
X
T
P
A
G
E
P
A
G
E
B
A
C
K
Recording time code, input to the DV IN/OUT terminal
TC/UB/CLOCK(1/2) Menu screen
–
–
–
T
C
/
U
B
/
C
L
O
C
K
1 (
2 /
T
C
G
S
O
U
R
C
E
I
N
T
C
G
S
E
L
E
C
T
P
R
T
C
G
M
O
D
E
R
E
N
D
/ F
D
F
(
N
T
S
C
)
–
–
D
F
B
T I
(
P
A
) L
O
N
T
C
D
U
P
I L
C
A
T
E
A
U
T
C
O
F
F
S
E
T
O
F
N
E
X
T
P
A
G
E
P
A
G
E
B
A
C
K
Memo
Time codes input to the
TIME CODE IN terminal
are ignored.
Do not connect any device
to the TIME CODE OUT
terminal.
:Setting:
● Set the TC/UB/CLOCK(1/2) Menu as follows.
)–
–
–
T
E
R
N
A
L
TCG SOURCE
G
E
N
C
-
R
U
N
TCG SELECT
–
TCG MODE
F
F
NDF/DF (NTSC) : No setting is required. It will be in the same
:Operation:
1.
Insert a tape with time codes recorded.
2.
Set BR-DV6000 to the RECORDING PAUSE mode at the posi-
tion where time codes are to be recorded again.
3.
Press the PLAY button to go to the RECORDING mode.
¥ Time codes will be recorded on the tape, starting from where it
stopped at last recording.
The counter mode display shows either TCR or UBR.
:Setting:
)–
–
–
Set the INPUT SELECT switch on the front panel to DV.
T
E
R
N
A
L
E
S
E
T
Set TC DUPLICATE in the TC/UB/CLOCK(1/2) Menu
C
-
R
U
N
–
screen to AUTO.
T
O
* To record time codes in the NON DROP frame mode from BR-
F
DV600 or GY-DV500, set TC DUPLICATE to NON DROP.
:Operation:
1.
Check the time code of the DV input terminal.
Press the REC button when BR-DV6000 is in the STOP mode to
display the time code on the monitor or the LCD. It will be dis-
played while the button is held down.
The counter mode display shows DTCG or DUBG.
2.
Select the RECORDING mode.
¥ Record time codes from the DV input terminal.
Memo
● For date/time also, data from the DV IN terminal are recorded.
● When this terminal is connected to a D9 VCR, data/time data
are not recorded.
: INTERNAL
: REGEN
: No setting required. It will be in the same run-
ning mode as the tape.
frame mode as the tape.
61
Advertisement
Table of Contents
