Cleaning And Annual Maintenance - Space-Ray LTU 80– N5 Installation And Operation Instructions Manual

22.0)

CLEANING AND ANNUAL MAINTENANCE

This heater must be cleaned and serviced annually by a qualified contractor before the start of each heating
season and at any time excessive accumulation of dust and dirt is observed. Maximum heating efficiency and
clean combustion will be maintained by keeping the heater clean.
The contractor shall check the following during periodic maintenance.
Clearances to combustibles: Check that clearances are being maintained. Make sure there are no Clearances to combustibles:
• • • • Clearances to combustibles: Clearances to combustibles:
flammable objects, liquids or vapors near the heater. See also Section 4.0).
Reflectors: Reflectors: Reflectors: Reflectors: Reflectors should be kept clean, at a minimum blow off the reflectors. (Dirty reflectors may
• • • •
reduce heat output).
Heat exchanger tubes: Heat exchanger tubes: Inspect the heat exchanger tubes to make sure they are not cracked, sagging or Heat exchanger tubes: Heat exchanger tubes:
• • • •
showing signs of fatigue.
Combustion air intake: Disconnect combustion air intake from the control box and inspect internally using a Combustion air intake:
• • • • Combustion air intake: Combustion air intake:
flashlight to make sure no foreign material has collected in the tubes and that there is no obstruction
around the air intake openings. Clean any foreign materials. Inspect any joints to make sure they are
completely sealed. See also Section 18.0).
Venting System: Disconnect vent pipe and inspect internally using a flashlight to make sure no foreign Venting System:
• • • • Venting System: Venting System:
material has collected in the pipes. Check the external vent cap and make sure that there is no obstruction
around the exhaust openings. Clean any foreign materials. Inspect any joints to make sure they are
completely sealed. See also Section 17.0).
Gas lines: Make sure that the gas lines are not leaking. Check the gas connection to the heater for any signs Gas lines:
• • • • Gas lines: Gas lines:
of damage, fatigue or corrosion. If there are any signs of damage to the gas connection or leaks found in the
gas piping, immediately stop using the heater until the gas pipe and connections have been repaired or
replaced. Check that the gas lines are not bearing the weight of the heater. See also Section 14.0).
Control Control Box: Control Control Box: Box: Box: In order to extend the longevity of the heater, the heat exchanger tube and the burner must be
• • • •
level. Check that the control box is level; use the turnbuckle on the burner suspension eyebolt to adjust the
level of the burner. See also Section 5.0).
Blower wheel and housing: Check that the blower wheel spins freely, blow out any dust or dirt with Blower wheel and housing: Blower wheel and housing: Blower wheel and housing:
• • • •
compressed air.
Electrode condition: Visually check that the electrode gap is maintained at 3/16" and that the tips of the Electrode condition:
• • • • Electrode condition: Electrode condition:
spark electrode are free from deposits. Clean off any deposits. Check that the electrode ceramic is free from
cracks. See Section 24.1).
Suspension system: Suspension system: Check that the suspension system is holding the heater level. Make sure that the heater
• • • • Suspension system: Suspension system:
is hanging securely, look for any evidence where the heater may have been hit accidentally and tighten any
loose hanging points. Check that S hooks are closed. Check that there is no evidence of wear on the chain at
the connection to the heater and at the ceiling.
Main Burner and Orifice: Check the Main burner and orifice; remove any dirt or debris including spider webs. Main Burner and Orifice:
• • • • Main Burner and Orifice: Main Burner and Orifice:
See Section 24.1).
Form #43155010
May 2013
ELECTRIC SHOCK & EXPLOSION HAZARD
-47-