Basic Operations; Turn On The Power; Select The Source To Play; Adjust The Volume - JVC LVT0858-001A Instructions Manual

Basic Operations

This manual mainly explains operations using the buttons and controls on the front panel. You can also use the buttons on the remote
control if they have the similar names (or marks) as those on the front panel.
If operations using the remote control are different from those using the front panel, they are then explained.
• You can also see "Mastering Remote Operations" on page 38.
STANDBY lamp TV DIRECT
STANDBY
STANDBY/ON
PHONES
PHONES jack
1
STANDBY/ON
1

Turn On the Power

Press STANDBY/ON (or AUDIO
remote control).
The STANDBY lamp goes off. The current
source indicator lights green. The name of the
current source (or station frequency) appears on
the display.
Current volume level is shown here.
L R
LPCM
Current source name appears.
To turn off the power (into standby)
Press STANDBY/ON again (or
AUDIO on the remote control).
The STANDBY lamp lights up.
Note:
A small amount of power is consumed in standby mode. To turn the
power off completely, unplug the AC power cord.
2

Select the Source to Play

Press one of the source selecting buttons.
DVD STB VCR
DVD : Select the DVD player.
STB : Select the STB.
VCR : Select the VCR.
TV : Select the TV tuner.
TAPE
: Select the cassette recorder.
FM/AM : Select an FM or AM (MW/LW) broadcast.
The selected source indicator lights green.
10
Display
TV DIRECT
DVD STB
CONTROL
ANALOG L C R
LPCM DSP
SUBWFR LFE
AUTO SR
DOLBY D
LS S RS
DTS INPUT ATT
SETTING ADJUST MEMORY
DVD STB
on the
STANDBY
STANDBY/ON
VOL
STANDBY
STANDBY/ON
TV TAPE FM / AM
Source indicators
HOME CINEMA CONTROL CENTER
VCR TV TAPE FM/AM
PL ΙΙ SLEEP AUTO MODE TA HEWS INFO RDS TUNED ST AUTO MUTING
HP
MH
Z
KH
Z INPUT
VOL
ANALOG/DIGITAL
VCR TV TAPE FM/AM INPUT ATT
2
Source selecting buttons
Note:
When you have connected some digital source components using the
digital terminals (see page 7), see "Basic Settings" on pages 13 and
14 to finish the digital input terminal setting and digital input mode
setting correctly before use.
3

Adjust the Volume

To increase the volume,
press and hold MASTER VOLUME
(or VOLUME + on the remote control).
To decrease the volume,
press and hold MASTER VOLUME
(or VOLUME – on the remote control).
CAUTION:
Always set the volume to the minimum before starting any sources. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
Notes:
• The volume level can be adjusted within the range of "0" (minimum)
to "70" (maximum).
• Each time you press the button, the volume level changes by
2 steps from "0" (minimum) to "14," and by 1 step from "14" to "70"
(maximum).
Listening with headphones
Connect a pair of headphones to the PHONES jack on the front
panel. This cancels the Surround mode currently selected,
deactivates speakers, and activates the HEADPHONE mode. The
HP indicator lights up on the display.
• Disconnecting a pair of headphone from the PHONES jack
cancels the HEADPHONE mode and activates speakers.
HEADPHONE mode
When using the headphones, following signals are output
regardless of your speaker setting:
— For 2 channel sources, the front left and right channel signals
are output directly from the left and right headphones.
— For multichannel sources, the front left and right, center and
rear channel signals are down-mixed and then output from the
headphones without missing bass element.
You can enjoy multichannel sound source using the
headphones.
SURROUND SURROUND
ON/OFF MODE
MASTER VOLUME
3
MASTER VOLUME
MASTER VOLUME
/