Hilti SCM 22-A Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Saw
  5. SCM 22-A
  6. Operating instructions manual

Hilti SCM 22-A Operating Instructions Manual

Cordless circular saw
Hide thumbs Also See for SCM 22-A:
Table of Contents

Advertisement

Quick Links

See also: Manual , Operating Instructions Manual
Printed: 12.03.2014 | Doc-Nr: PUB / 5075277 / 000 / 03
SCM 22-A
Operating instructions
Brugsanvisning
Bruksanvisning
Bruksanvisning
Käyttöohje
Инструкция по зксплуатации
Ръководство за обслужване
Instrucţiuni de utilizare
Kulllanma Talimatı
Lietošanas pamācība
Instrukcija
Kasutusjuhend
Пайдалану бойынша басшылы
en
da
sv
no
fi
ru
bg
ro
tr
ar
lv
lt
et
қ
kk
ja
ko
zh
cn

Advertisement

Table of Contents
loading

Related Manuals for Hilti SCM 22-A

Summary of Contents for Hilti SCM 22-A

  • Page 1 SCM 22-A Operating instructions Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Инструкция по зксплуатации Ръководство за обслужване Instrucţiuni de utilizare Kulllanma Talimatı Lietošanas pamācība Instrukcija Kasutusjuhend қ Пайдалану бойынша басшылы Printed: 12.03.2014 | Doc-Nr: PUB / 5075277 / 000 / 03...
  • Page 2 Printed: 12.03.2014 | Doc-Nr: PUB / 5075277 / 000 / 03...
  • Page 3 Printed: 12.03.2014 | Doc-Nr: PUB / 5075277 / 000 / 03...

  • Page 4: Table Of Contents

    In these operating instructions, the designation “the the first time. power tool” always refers to the SCM 22-A cordless circular saw. Always keep these operating instructions to- gether with the power tool.

  • Page 5: Description

    Do not use the battery as a power source for other unspecified appliances. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance.

  • Page 6: Insert Tools, Accessories

    2.8 Items supplied as standard Power tool Saw blade Hexagon socket wrench Operating instructions Hilti toolbox (optional) Cardboard box (optional) Rip fence 2.9 Additional items required for operating the tool B22/2.6 or B22/3.3 Li‑ion battery and C4/36, C4/36‑ACS, C4/36‑90 or C4/36‑350 charger.

  • Page 7: Technical Data

    Noise and vibration information for the SCM 22-A (measured in accordance with EN 60745-2-5): Depending on how the saw is used, the values may increase.

  • Page 8: Safety Instructions

    Battery B 22/3.3 Li‑Ion B 22/2.6 Li‑Ion Weight 0.78 kg 0.78 kg Type of cell Li‑Ion Li‑Ion No. of cells Deep discharge protection 5 Safety instructions NOTE a cord suitable for outdoor use reduces the risk of electric shock. The safety rules in section 5.1 contain all general safety rules for power tools which, in accordance with the If operating a power tool in a damp location is applicable standards, must be listed in the operating...
  • Page 9 motor housing. If both hands are holding the saw, controlled with the switch is dangerous and must be repaired. they cannot be cut by the blade. c) Disconnect the plug from the power source b) Do not reach underneath the workpiece. The guard and/or the battery pack from the power tool cannot protect you from the blade below the work- before...
  • Page 10 may occur. Investigate and take corrective actions b) Always hold the power tool securely with both to eliminate the cause of blade binding. hands on the grips provided. Keep the grips dry, clean and free from oil and grease. c) When restarting a saw in the workpiece, centre the saw blade in the kerf and check that saw c) Breathing protection must be worn if the power teeth are not engaged into the material.

  • Page 11: Before Use

    Empty the chip collector and clean the power flammable materials, and allow it to cool down. tool before putting it away in the toolbox or other Contact Hilti Service after the battery has been container for storage or transport. Metal chips may allowed to cool.

  • Page 12: Operation

    Pull the battery out of the locked position (working pos- (not pressed). Use only the Hilti batteries approved ition) and move it into the first click-stop position (trans- for use with this power tool.
  • Page 13 CAUTION 7.2 Adjusting the cutting depth 4 Do not saw off very narrow strips. Narrow strips may The cutting depth can be infinitely adjusted between 0 be caught by the blade and pulled in, causing jamming, and 57 mm. or may be thrown out, presenting a risk of injury. Pull the battery out of the power tool.

  • Page 14: Care And Maintenance

    After carrying out care and maintenance work on the power tool, check that all protective and safety devices Charge the battery using an approved charger from Hilti are fitted and that they function faultlessly. designed for use with Li-ion batteries.

  • Page 15: Troubleshooting

    The battery runs down more Battery condition is not optimal. Have battery condition diagnosed by quickly than usual. Hilti Service or replace with a new battery. The battery does not engage The retaining lugs on the battery are Clean the retaining lugs and check with an audible double click.

  • Page 16: Manufacturer's Warranty - Tools

    Dispose of the batteries in accordance with national regulations or return them to Hilti. Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling.
  • Page 17 Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 4082 | 0214 | 00-Pos. 8 | 1 Printed in China © 2014 Right of technical and programme changes reserved S. E. & O.

Table of Contents