Hilti SCM 22-A Operating Instructions Manual page 10

may occur. Investigate and take corrective actions
to eliminate the cause of blade binding.
c) When restarting a saw in the workpiece, centre
the saw blade in the kerf and check that saw
teeth are not engaged into the material. If saw
blade is binding, it may walk up or kickback from the
workpiece as the saw is restarted.
d) Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag
under their own weight. Supports must be placed
under the panel on both sides, near the line of cut
and near the edge of the panel.
e) Do not use dull or damaged blades. Unsharpened
or improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback.
f) Blade depth and bevel adjusting locking levers
must be tight and secure before making cut. If
blade adjustment shifts while cutting, it may cause
binding and kickback.
g) Use extra caution when sawing into existing walls
or other blind areas. The protruding blade may cut
objects that can cause kickback.
5.2.3 Safety instructions for circular saws with
outer pendulum guard
Lower guard function
a) Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does
not move freely and close instantly. Never clamp
or tie the lower guard into the open position. If saw
is accidentally dropped, lower guard may be bent.
Raise the lower guard with the retracting handle and
make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of
cut.
b) Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use. Lower
guard may operate sluggishly due to damaged parts,
gummy deposits, or a build-up of debris.
c) Lower guard may be retracted manually only for
special cuts such as "plunge cuts" and "com-
pound cuts." Raise lower guard by retracting
handle and as soon as blade enters the mater-
ial, the lower guard must be released. For all other
sawing, the lower guard should operate automatic-
ally.
d) Always observe that the lower guard is covering
the blade before placing saw down on bench or
floor. An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its
path. Be aware of the time it takes for the blade to
stop after switch is released.
5.3 Additional safety instructions
5.3.1 Personal safety
a) Wear ear protectors. Exposure to noise can cause
hearing loss.
b) Always hold the power tool securely with both
hands on the grips provided. Keep the grips dry,
clean and free from oil and grease.
c) Breathing protection must be worn if the power
tool is used without a dust removal system for
work that creates dust.
d) Do not operate the power tool without the pro-
tective devices that belong to it.
e) Operate the power tool only as intended and when
it is in faultless condition.
Improve the blood circulation in your fingers by
f)
relaxing your hands and exercising your fingers
during breaks between working.
g) Switch the power tool on only after bringing it into
position at the workpiece.
h) Remove the battery before storing or transporting
the power tool.
i) Always guide the power tool away from your body
when working with it.
Do not work with the power tool overhead.
j)
k) Do not attempt to brake the speed of the saw
blade by pressing it to the side.
l) Do not touch the clamping flange or the clamping
screw while the power tool is running.
m) Never press the drive spindle lock button while
the saw blade is rotating.
n) Never direct the power tool toward persons.
o) Adjust the pressure applied to the saw blade and
the material being cut so that the blade does not
stall, possibly causing the power tool to kick back.
p) Avoid overheating the tips of the saw blade teeth.
q) Metal cuttings are sharp and present a risk of injury.
Keep your clothing closed so that metal cuttings
cannot find their way into your gloves, shoes or
other parts of your clothing.
r) Pay attention to the direction in which the metal chips
fly when sawing. The chips are hot and may cause
fires or lead to burning and cutting injuries.
s) Children must be instructed not to play with the
power tool.
t) The power tool is not intended for use by children,
by debilitated persons or those who have received
no instruction or training.
u) Dust from materials such as paint or coatings
containing lead, mineral materials and metals may
present a health hazard. Contact with or inhalation
of the dust may cause allergic reactions and/or
respiratory diseases among operators or bystanders.
Certain dusts are considered to be carcinogenic
(cancer-causing), especially in conjunction with
other substances (chromate). Material containing
asbestos may be worked on only by specialists.
Ensure that the workplace is well ventilated.
The use of a dust mask of filter class P2 is
recommended. Follow national requirements for
the materials you want to work with.
en
7