JUKI DDL-5550N Handbook page 166

OPTIONS
Model Part No.
PGM-5A
B5019-222-0B0
PV-150209000
142-04754
PX-5000014000
SS-6152212SP
WP-0612516SD 2
B2120-215-0A0
B4150-210-DA0
B4720-215-DB0
MU08
MU11
B2581-223-CA0
B2582-223-CA0
B2581-224-CA0
B2582-224-CA0
B2640-215-0B0
B2641-215-0A0 2
SS-6150610SP 4
Part No.
B1601-220-000 Intermediate presser A 2.2 3.6 6 29.5
B1601-220-00B Intermediate presser B 3.5 5.5 6 29.5
B1601-220-00C Intermediate presser C 2.2 3.6 12 6 29.5
B1601-220-00D Intermediate presser D 2.2 12 34.5
B1601-220-00E Intermediate presser E
B1601-220-00F Intermediate presser F
B1601-220-00G Intermediate presser G 2.7 4.1 5 29.5
B1601-220-0A0 Intermediate foot (asm) 2.2 10 6 29.5
B2587-220-000 Work clamp paper material (A)
B2588-220-000 Work clamp paper material (B)
B2595-220-00A Presser cloth sheet (t=1mm)
B2595-220-00B Presser cloth sheet B (t=3mm)
B2595-220-00B Presser cloth sheet (t=2mm)
B2622-223-C00 Feeding frame blank, right (with knurl)
B2623-223-C00 Feeding frame blank, left (with knurl)
B2626-223-C00 2-step feeding frame blank (without knurl)
B2620-223-C00 Feeding frame blank plate (with knurl)
B2621-223-C00 Feeding frame blank plate (without knurl)
B2556-223-C0B Lower plate blank (without knurl)
B2556-223-C0C Lower plate blank (with knurl)
B2556-223-C0D Lower plate blank (0.5mm, without knurl)
B2556-224-C0A Lower plate blank (without knurl)
B2426-210-00A Needle hole guide A ( A = 1.6)
B2426-210-00B Needle hole guide B ( A = 2.0)
B2426-210-00C Needle hole guide C ( A = 1.6)
B2426-210-00D Needle hole guide D ( A = 2.4)
B2426-210-00F Needle hole guide F ( A = 3.0)
B2426-210-00G Needle hole guide G ( A = 3.0)
B2426-210-00H Needle hole guide H ( A = 3.0)
Description
Handy programming device
Thread tension controller No.3
Needle thread clamp device
Junction cord
Needle cooler
Milling unit
Milling unit
Cassette holder fixing base (asm.)
Cassette holder (asm.)
Cassette holder fixing base (asm.)
Cassette holder (asm.)
One-touch utility clamp
1.6 2.6 6 29.5
2.2 3.6 9 29.5
AMS-223
AMS-224
Handy type of programming device provided with many
different functions enable the operator to input data by
operating the device near needle entries.
The tension controller unit is used to partially change the
needle thread tension during the sewing of a pattern.
This device prevents the thread from tangling at the start of
sewing.
The needle cooler blows air to the needle, thereby preventing
thread breakage caused by hot needle.
AMS-223
The milling unit can be installed on the machine to allow the
operator to easily machine a feeding frame or feed plate.
AMS-224
AMS-223
The next material to be sewn can be placed between the top
and bottom plates of the cassette holder while the machine
is still engaged in the sewing of the currently set material.
AMS-224
The feeding frame and the feed plate can be quickly changed
without any tools.
Description
L
A
R
R
B
B R L
A A
A, B, E, F and G type
AMS-223C, 224C, 223P, 224P (September, 2003) 3/4
Feature
A
L
A
C
B
C R L
B A B L
C type D type
A
11
L
B