JVC 0503-AH-ID-JVE Instructions Manual page 49

I
Set the VPS/PDC mode.
A Press
to move the arrow to "VPS/PDC".
r t
B Press VPS/PDC to select "ON" or "OFF".
OR
A Press
to move the arrow to "VPS/PDC", then
r t
press OK.
B Press
to select the desired setting, then press OK.
r t
If "VPS/PDC ON" is displayed on the TV screen, VPS/PDC is
set to ON.
If "VPS/PDC OFF" is displayed on the TV screen, VPS/PDC is
set to OFF.
"VPS/PDC Recording" on page 49.
J
Set the WEEKLY/DAILY programme mode.
A Press
to move the arrow to "WEEKLY/DAILY",
r t
then press OK.
B Press
to select the desire mode, then press OK.
r t
For details on each mode, see "WEEKLY/DAILY programme
timer settings" ( pg. 47).
K
Set other options.
A Press
to move the arrow to the desired option,
r t
then press OK.
B Set each option as required.
To modify a programme title, perform steps B and C of
"Modify Programme Title" (
To modify the category option, press
desired category, press OK, press
arrow to "EXIT", then press OK.
L
Return to the normal screen.
Press to move the arrow to "EXIT", then press OK.
w e
If "PROGRAMME OVERLAPPED" appears on the TV screen,
see page 50.
To continue timer programming for other programmes, press
to move the arrow to "CONTINUE", then press OK.
w e
M
Engage the recorder's timer mode.
For the HDD deck (with the VPS/PDC mode is OFF):
No operation is required to engage the recorder's mode.
For the VHS deck and the HDD deck (with the VPS/
PDC mode is ON):
Press (TIMER). The recorder turns off automatically and
#
" " appears on the front display panel.
#
To disengage the timer mode, press
NOTES:
During timer recording with "
display panel, it is not possible to change the recording deck
(HDD or VHS).
When you check , cancel, or change programme, see page 50.
pg. 57).
to select the
w r e t
to move the
w r e t
(TIMER) again.
#
" appearing on the front
#
Satellite Receiver Users
To timer-record a satellite broadcast using Express Timer
Programming:
A Perform "Satellite Receiver Control Setting" on page 19.
B Perform steps A – M. In step G, change "TV PROG" to
"SAT". The front display panel shows "L-2" for the
channel position. Then select the channel position for the
satellite broadcast. In step I, you cannot set "VPS/PDC"
to "ON".
C Leave the satellite receiver's power on.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) and VPS (Video Programme System) are
service designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video recorder and have precedence over the
advertised times you may have preset into the timer. This
means that your recorder will start and stop recording when
the preset TV programmes actually start and end — even if
the broadcast time of a preset TV programme is changed.
NOTES:
When you use Express Timer Programming, set the start
time (VPS or PDC time) exactly as advertised in the TV
listing. A different time than advertised will result in no
recording.
VPS/PDC recording is also possible when a satellite
receiver or a cable system is connected to L-2 IN/
DECODER connector on your recorder.
VPS/PDC recording is also possible via the L-1 IN/OUT
connector.
How to check if the station being received transmits a
VPS/PDC signal (VHS deck only)
A Press – –:– – until the channel position appears on the
front display panel.
B Hold down
for about 5 seconds.
"VPS/PDC" appears blinking on the front display panel.
If a VPS/PDC signal is detected from the station,
"VPS/PDC" will stop blinking.
If no VPS/PDC signal is detected from the station,
"VPS/PDC" will blink at a slower rate.
C Press – –:– – or
again to return to normal display.
49
EN