Siemens RDF300 Documentation page 28

# Parameter
Expert Level
P30 P-band/Switching differential for heating mode
P31 P-band/Switching differential for cooling mode
P33 Dead zone in Comfort mode
P34 Setpoint differential
P35 Integral time
P36 Heating/cooling changeover switching point for cooling
P37 Heating/cooling changeover switching point for heating
P38 X1 functionality
P39 Operating action for X1 if digital input
P40 X2 functionality
P41 Operating action for X2 if digital input
P44 Runtime for 3-position output (Y11/Y21)
P48 Minimum output on-time via on/off control output
P49 Minimum output off-time via on/off control output
P50 Purge function (minimum every 2 hours)
P51 Floor heating limit temperature
P52 Fan operation
P53 Fan speed
P54 Fan overrun time (only when electric heater is used)
P55 Switching point fan speed high
P56 Switching point fan speed med
P57 Switching point fan speed low
P58 Fan start kick
P59 Fan minimum on-time
P60 Fan kick in Comfort mode (time to next kick)
P61 Fan kick in Energy Saving mode (time to next kick)
P62 Clean filter reminder runtime
P65 Heating setpoint for Standby
P66 Cooling setpoint for Standby
P69 Temporary setpoint for Comfort mode
P70 Infrared receiver
P71 Parameter reset
Set value to ON and confirm by pressing the + and – buttons
Diagnostic & Test
d01 Application
d02 Status input X1
d03 Status input X2
d05 Test mode to check the 3-position Y11/Y21 actuator direction.
Note that this parameter can be quit only if the setting is back
at "---" and by pressing + and – buttons
28 / 40
Siemens
Building Technologies
(Wheat )
Stb
(Wcool )
Stb
RDF300.../RDF340.../RDF400... Basic Documentation
4BFunctions
Factory
Setting range
setting
2K 0.5 ... 6 K
1 K 0.5 ... 6 K
2 K 0.5 ... 5 K
2 K 0.5 ... 5 K
5 min 0...10 min
16 °C 10...25 °C
28 °C 27...40 °C
3 (Op mode 0:= NA
switchover) 1:= Ext/Return air temp
2:= Heat/cool changeover
3:= Operating mode switch
4:= Dewpoint monitor
5:= Enable electrical heater
6:= Alarm input
0 (N.O.) 0:= Normally open
1:= Normally closed
2 (H/C c/o) Same as P38
0 (N.O.) 0:= Normally open
1:= Normally closed
150 s 50...240 sec
1 min. 1...20 minutes
1 min. 1...20 minutes
OFF OFF: Inactive
1...5 min
OFF OFF, 10..50 °C
1 (Enabled) 0:= Disabled
1:= Enabled
2:= Only in heating
3:= Only in cooling
2 (3-speed) 1:= 1-speed
2:= 3-speed
60 sec 0 ... 300 sec
100% 80..100%
65% 30..75%
10% 1..15%%
ON ON: enabled
OFF: disabled
2 min 1 ... 5 min
0 (continuous) 0...89min, OFF
OFF 0...359min, OFF
OFF OFF, 100 ... 9900 hours
8 °C OFF, 5 °C...Wcool
OFF OFF, Wheat
OFF OFF:= Disabled
ON := Enable
OFF OFF:= Disabled
ON := Enable
OFF OFF:= Idle
ON: = Reset
Diagnose 2P:= 2-pipe
2PEL:= 2-pipe & el. heater
4P:= 4-pipe
2P3P:= 2-pipe 3pos
Diagnose 0:= Digital input
not activated
1:= Digital input activated
0...49 °C = measured
00 := H/C input short
100:= H/C input open
Diagnose Same as d02
Diagnose "---" := no signal
OPE:= Y11 active
CLO:= Y21 active
Stb
...40 °C
Stb
temp. value
open
close
CE1P3076en
28 Aug 2008