Marley HTWH Series Instructions Manual

Smart series large wall heater

Advertisement

Quick Links

HTWH Series
Smart Series
Large Wall Heater
READ CAREFULLY - This manual provides instructions for the correct installation, safe use, and care of this product. Special atten-
tion should be directed to the warnings provided below which identify certain precautions and special instructions for safe and effi-
cient installation and use. Studying these instructions first may save you considerable time and money later and keep your installa-
tion time to a minimum. If you are not familiar with electricity or feel uncomfortable in working with electricity, refer the installation of
this product to a licensed electrician or qualified person.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
INJURY TO PERSONS:
1. READ ALL INSTRUCTIONS before installing or using the
heater.
2. ELECTRICAL SHOCK HAZARD: Disconnect all electrical
power coming to heater at circuit breaker box or main
disconnect switch and lock in OFF position before wiring.
All wiring must be in accordance with The National Electrical
Code and applicable local codes and ordinances.
The heater must be properly connected to an effective
building ground.
3. Verify the supply voltage coming to heater is the same as
shown on the heater nameplate before energizing.
Energizing at a voltage in excess of nameplate voltage will
damage heater and void warranty.
4. This heater has hot and arcing or sparking parts inside.
Do not install or use in areas where gasoline, paint, or flam-
mable liquids are used or stored.
5. Do not install this heater upside down, sideways, in ceiling,
or floor. Install only as shown in this manual. Refer to
Mounting Clearances, page 2 for minimum clearances that
must be maintained.
6. The heater assembly must be installed in the back box pro-
vided. Do not operate the heater without the grille installed.
7. This heater is not approved for use in corrosive
atmospheres such as marine, green house or chemical
storage areas.

IMPORTANT INSTRUCTIONS

WARNING
SAVE THESE INSTRUCTIONS
19-3/16"
(487mm)
!
8. Do not use outdoors.
9. Extreme caution is necessary when any heater is used by or
near children or invalids and whenever the heater is left
operating or unattended.
10. This heater is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces. Keep combustible materials,
such as furniture, pillows, bedding, papers, clothes, and
curtains away from heater. Do not block air intakes or
exhaust in any manner. For efficient and safe operation, we
recommend keeping all items at least 3 feet from front of
heater.
11. Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock, fire,
or damage the heater.
12. Should the heater become blocked or otherwise overheat, it
is provided with a manual-reset thermal safety switch and
alarm light that will activate to alert that the heater has
cycled off. If warning light is on, check to see if the reason
for the overheating can be identified.
blockage, allow heater to cool, then press Reset button.
Heater should return to normal operation. Do not continue
to use heater if it repeatedly cycles off. Have it inspected
and repaired by a qualified repair person.
13. Use this heater only as described in this manual. Any other
use not recommended by the manufacturer may cause fire,
electric shock, or injury to persons.
15-21/64"
(389mm)
14-3/8"
(365mm)
1-21/32"
(42mm)
Remove any
5/14"
(133mm)
18-1/4"
464mm

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HTWH Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Marley HTWH Series

  • Page 1: Important Instructions

    5/14" (133mm) 15-21/64" (389mm) 18-1/4" 19-3/16" 464mm (487mm) HTWH Series Smart Series 14-3/8" (365mm) 1-21/32" Large Wall Heater (42mm) IMPORTANT INSTRUCTIONS READ CAREFULLY - This manual provides instructions for the correct installation, safe use, and care of this product. Special atten- tion should be directed to the warnings provided below which identify certain precautions and special instructions for safe and effi- cient installation and use.
  • Page 2: Specifications

    SPECIFICATIONS Min. Supply TO PREVENT POSSIBLE DAMAGE TO POWER WIRING, Catalog Wire USE ONLY THE KNOCKOUTS PROVIDED IN BACK BOX. Number Volts Phase Watts Amps Gauge HTWH4008* 1800-4000 19.2 Mounting Back Box in New Construction (See Figure 1). HTWH4004* 1800-4000 16.7 HTWH4007* 1800-4000...
  • Page 3 Installation of Recessed Back Box 7. Secure disconnect switch bracket in place by tightening screws. in Existing Construction 8. Insert back box in wall opening being careful not to damage 1. Provide a wall opening 14-1/2" (362mm) wide by 18-1/2" the supply wiring.
  • Page 4: Operation

    8. Connect building ground conductor to the back box by Installation of Grille and Control Wire Connector connecting the supply ground leadwire to the green ground 1. Position the grille in front of the heater assembly, extend the screw located in the inside top of the back box. wire connector from the heater assembly to the matching 9.
  • Page 5 10.BMS (Building Management System): This feature is for optional use by building management systems. A red jumper wire connecting terminal A and B on the electronic power board can be removed and replaced by a Building Management System Switch. DO NOT REMOVE THE RED JUMPER UNLESS CONTROL BY A BUILDING MANAGE- MENT SYSTEM IS BEING USED.
  • Page 6: Maintenance

    MAINTENANCE Your heater is designed for years of trouble-free operation and requires no special maintenance other than occasional cleaning. The motor is permanently lubricated. Cleaning At least once each year (or more often in dirty environments), the heater should be cleaned to remove dust and other foreign material which has collected during the heating season, as follows: THE OUTSIDE SURFACES MAY BE CLEANED WITH MILD...
  • Page 7: Repair Parts

    REPAIR PARTS Repair Parts List Part Number HTWH4008 HTWH4004 HTWH4007 Description 208V 4000W 240V 4000W 277V 4000W Quantity Northern White Grille 2501-11017-000 2501-11017-000 2501-11017-000 Navajo White Grille 2501-11017-001 2501-11017-001 2501-11017-001 Stat Bronze Grille 2501-11017-002 2501-11017-002 2501-11017-002 Back Box assembly 1203-2015-000 1203-2015-000 1203-2015-000 Parts Bag (not shown)
  • Page 8: Limited Warranty

    Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the nearest Marley authorized service cen- ter or the Marley Engineered Products Service Center, and we will repair or replace, at our option, at no charge to you with return freight paid by Marley. It is agreed that such repair or replacement is the exclusive remedy available from Marley Engineered Products.

Table of Contents