Subscribe to Our Youtube Channel
Related Manuals for Worx WU670l
Summary of Contents for Worx WU670l
- Page 1 SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS HigH frequency multi-function tool Wu670l...
-
Page 2: General Power Tool Safety Warnings
General power tool safety entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling warnings or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords Warning: Read all safety warnings and all instructions. - Page 3 e) Do not overreach. Keep proper footing and balance at all power tool repaired before use. Many accidents are caused by times. This enables better control of the power tool in unexpected poorly maintained power tools. situations. f) Keep cutting tools sharp and clean. Properly maintained cutting f) Dress properly.
- Page 4 Always check walls and ceilings to avoid hidden power cables and Warning! Some dust created by power sanding, sawing, pipes. A metal detector can be obtained from any good DIY store for grinding and other construction activities contains chemicals this purpose. known to cause cancer, birth defects or other reproductive If possible, use clamping devices or other suitable means to secure harm.
- Page 5 Symbols To reduce the risk of injury, user must read instruction manual Double insulation Warning Wear eye protection Wear dust mask Wear ear protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
-
Page 6: Component List
Component list Venting slots Scraper * Dust extraction attachment * Sanding paper * Sanding Pad Perforated * Sanding paper Perforated * Allen key Fastening piece Universal end cut blade * Carbide grit semicircle saw blade * HSS semicircular saw blade * Carbide rasp, perforated * On/Off switch Variable speed control... -
Page 7: Technical Data
Technical data Warning: The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used dependant on the following examples and • Voltage 110V~50Hz other variations on how the tool is used: •... - Page 8 Accessories • Allen key • End cut blade • Sanding pad-dust extraction • HSS semicircle saw blade • Plastic sanding • Carbide grit segment saw blade standard • Triangular carbide rasp • Plastic sanding pad (unperforated) Dust extraction adapter • •...
-
Page 9: Intended Use
Operation instructions Note: Before using the tool, read the instruction book carefully. INTENDED USE The power tool is intended for sawing and separating wooden materials, plastic, plaster, non-ferrous metals and fasteners (e.g. nails and clamps) as well as for working on soft wall tiles and for dry grinding of small surfaces. - Page 10 Reposition the fastening piece (8) and tighten the bolt using the supplied Allen key. USING ADAPTERS (16) (See A3) ® ® Accessories of other brands ( Fein , Bosch ) can be fitted onto the ® Sonicrafter using the adapter. Note: Fein is a registered trademark of C.
-
Page 11: Operating The On/Off Switch
and place it on again. MOUNTING THE SUCTION DEVICE (See C1-D2) When vacuuming, mount the suction device as shown in C1-D2. Note: Using the sanding pad perforated. You can only do the vacuuming after fitting the dust collector. OPERATING THE ON/OFF SWITCH Start the machine, push the On/Off switch (13) forward so that the “I”... - Page 12 SAWING WITH THE SEMICIRCLE SAW BLADE The workpiece must be inserted firmly or clamped tightly before it is cut. Typical application: wood, PVC, soft metal sheet. Select high oscillation frequency . The saw blade lasts longer if the wear is distributed evenly. To ensure an even distribution, loosen the saw blade, rotate it and retighten firmly.
-
Page 13: Working Hints For Your Tool
Working hints for your tool water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. If your power tool becomes too hot, especially when used at low Occasionally you may see sparks through the ventilation slots. -
Page 14: Plug Replacement (Uk & Ireland Only)
Plug replacement (UK & Ireland only) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE =NEUTRAL BROWN =LIVE As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. -
Page 15: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY Positec Power Tools (Europe) Ltd, PO Box 152, Leeds, LS10 9DS, UK Declare that the product, Description WORX High frequency multi-function tool Type WU670L Function Sawing,scraping,sanding Complies with the following directives, • EC Machinery Directive 2006/42/EC •...
Need help?
Do you have a question about the WU670l and is the answer not in the manual?
Questions and answers