Cisco Codec C60 Administrator's Manual page 72

Cisco TelePresence System Codec C60/C40 and Profiles using C60/C40
Contents Introduction
Experimental Audio Input Microphone [1..2]/[1..4] Channel
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.
Defines whether the signal from the microphone is a mono signal or part of a multichannel signal.
Requires user role: ADMIN
Value space: <Left/Right/Mono>
Left: The microphone signal is the left channel of a stereo signal.
Right: The microphone signal is the right channel of a stereo signal.
Mono: The microphone signal is a mono signal.
Example: Experimental Audio Input Microphone 1 Channel: Mono
Experimental Audio MicrophoneReinforcement Gain
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Microphone reinforcement is local amplification of one or several input connectors, directly to one
or several output connectors, with minimum delay.
For software version TC4.0: Microphone reinforcement should not be enabled on a codec that is
also configured using the Audio Console application.
This setting configures the gain of this path, from -53 dB to +15 dB. The value -54 corresponds to
mute.
Requires user role: ADMIN
Value space: <-54..15>
Example: Experimental Audio MicrophoneReinforcement Gain: -19
Experimental Audio MicrophoneReinforcement AGC
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Microphone reinforcement is local amplification of one or several input connectors, directly to one
or several output connectors, with minimum delay.
For software version TC4.0: Microphone reinforcement should not be enabled on a codec that is
also configured using the Audio Console application.
This setting controls an AGC on the mix of all input connectors attached to the Microphone
reinforcement.
Requires user role: ADMIN
Value space: <On/Off>
Example: Experimental Audio MicrophoneReinforcement AGC: Off
D14636.06 Profile C60-C40 and Codec C60-C40 Administrator Guide TC4.2, July 2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Web interface Advanced settings Advanced settings
Experimental Audio MicrophoneReinforcement Input Microphone [1..4] Mode
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Microphone reinforcement is local amplification of one or several input connectors, directly to one
or several output connectors, with minimum delay.
For software version TC4.0: Microphone reinforcement should not be enabled on a codec that is
also configured using the Audio Console application.
Configuring this setting to On for a microphone, means to attach it to the microphone
reinforcement for local amplification. This is done in parallel to the microphone's existing
connections, and will not affect any of these.
Requires user role: ADMIN
Value space: <On/Off>
Example: Experimental Audio MicrophoneReinforcement Input Microphone 1
Mode: On
Experimental Audio MicrophoneReinforcement Output Line [1..2] Mode
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Microphone reinforcement is local amplification of one or several input connectors, directly to one
or several output connectors, with minimum delay.
For software version TC4.0: Microphone reinforcement should not be enabled on a codec that is
also configured using the Audio Console application.
Configuring this setting to On for an output line, means to attach that output connector to the
microphone reinforcement for local amplification. If the output connector already is attached
to a Local Output, it will first be detached from that before being attached to the Microphone
reinforcement. When this setting is On, the output connector cannot be attached to any Local
Output.
Requires user role: ADMIN
Value space: <On/Off>
Example: Experimental Audio MicrophoneReinforcement Output Line 1 Mode: On
Experimental Audio Panning Mode
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <Off/Auto>
Example: Experimental Audio Panning Mode: Off
72
Password protection Appendices
Administrator guide
Contact us
www.cisco.com