Cisco Codec C60 Administrator's Manual page 39

Cisco TelePresence System Codec C60/C40 and Profiles using C60/C40
Contents Introduction
Audio Input Line [1..2] Level
Define the audio level of the Line input connector, in steps of 1 dB.
See the Audio Level tables in the Physical Interfaces Guide for the codec for a complete overview
of the menu values represented in dB.
Requires user role: ADMIN
Value space: <0..24>
Range: Select a value from 0 to 24 dB.
Example: Audio Input Line 1 Level: 10
Audio Input Line [1..2] LoopSuppression
NOTE: Codec C40/C60 does currently not support Loop Suppression, hence Loop Suppression
can be set to Off only.
Requires user role: ADMIN
Value space: <Off>
Off: Deactivate Loop Suppression.
Example: Audio Input Line 1 LoopSuppression: Off
Audio Input Line [1..2] Mode
Set the audio input line mode.
Requires user role: ADMIN
Value space: <On/Off>
On: Enable the Audio Line input.
Off: Disable the Audio Line input.
Example: Audio Input Line 1 Mode: On
Audio Input Microphone [1..2]/[1..4] EchoControl Mode
NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.
The echo canceller continuously adjusts itself to the audio characteristics of the room and
compensate for any changes it detects in the audio environment. If the changes in the audio
conditions are very significant the echo canceller may take a second or two to re-adjust.
Requires user role: ADMIN
Value space: <On/Off>
On: Echo Control is normally set to On to prevent the far end from hearing their own audio.
Once selected, echo cancellation is active at all times.
Off: Echo Control should be switched Off if external echo cancellation or playback equipment is
used.
Example: Audio Input Microphone 1 EchoControl Mode: On
D14636.06 Profile C60-C40 and Codec C60-C40 Administrator Guide TC4.2, July 2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Web interface Advanced settings Advanced settings
Audio Input Microphone [1..2]/[1..4] EchoControl NoiseReduction
NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.
The system has a built-in noise reduction which reduces constant background noise (e.g.
noise from air-conditioning systems, cooling fans etc.). In addition, a high pass filter (Humfilter)
reduces very low frequency noise. NOTE: Requires the Echo Control Mode to be enabled for the
microphone.
Requires user role: ADMIN
Value space: <On/Off>
Example: Audio Input Microphone 1 EchoControl NoiseReduction: On
Audio Input Microphone [1..4] EchoControl Dereverberation
The system has built-in signal processing to reduce the effect of room reverberation. NOTE:
Requires the Echo Control Mode to be enabled for the microphone.
Requires user role: ADMIN
Value space: <On/Off>
Example: Audio Input Microphone 1 EchoControl Dereverberation: On
Audio Input Microphone [1..2]/[1..4] Equalizer ID
NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.
Select the audio input microphone equalizer ID.
Requires user role: ADMIN
Value space: <1..16>
Example: Audio Input Microphone 1 Equalizer ID: 1
Audio Input Microphone [1..2]/[1..4] Equalizer Mode
NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.
Set the audio input microphone equalizer mode.
Requires user role: ADMIN
Value space: <On/Off>
Example: Audio Input Microphone 1 Equalizer Mode: Off
39
Password protection
On: The Noise Reduction should be enabled in the presence of low frequency noise.
Off: Turn off the Noise Reduction.
On: Turn on the dereverberation.
Off: Turn off the dereverberation.
Range: Select Equalizer ID 1 to 16.
On: Enable the equalizer for the audio input microphone.
Off: No equalizer.
Administrator guide
Appendices Contact us
www.cisco.com