Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for brace DWG 1000
- Page 1 User Guide Made in the USA...
-
Page 2: Table Of Contents
Table of Contents Introduction .................. 3 Wireless Audio for the 21st Century ..........3 How the DWG-1000 Works ............3 What's in the Box? ................4 Quick Start .................. 4 Transmitter (Tx) ................5 Receiver (Rx) ................6 Cable Strain Relief ................. 7 Placement of Tx/Rx Units .............. -
Page 3: Introduction
Older radio-based wireless systems had transmission problems, as well as clumsy antennas that had to be positioned just right. This is Digital baby, and Brace Audio’s unique digital technology does away with the hiss, crackle, signal loss and RF interference inherent with UHF /VHF systems. -
Page 4: What's In The Box
What’s in the box? Your DWG-1000 Digital Wireless Guitar System contains: • 1 - Transmitter (Tx / Gray Unit) • 1 - Receiver (Rx / Dark Green Unit) • 1 - AC Adapter (for Rx) • 2 - 1/4” to 1/8” Guitar Cables •... -
Page 5: Transmitter (Tx)
Transmitter Transmitter (Tx / Gray Unit) 1. Function Button 2. Link LED (”FN”) (”LINK”) Press the Function Button to initiate The LED lights solid when a wireless Mating Function if necessary. (see section, connection is made between the Tx and Rx Changing Channels). -
Page 6: Receiver (Rx)
LINK LOW B 5. Jack for AC Adapter 4. Audio Out Jack (”The Other Hole”) Use only the Brace Audio supplied or Plug the 1/8” connector on the included recommended power supply. cable into the Audio Out Jack, and the 1/4”... -
Page 7: Cable Strain Relief
Cable Strain Relief Remove belt clip on Transmitter. Thread cable through the notch in the clip, then snap the belt clip back onto Transmitter. This will provide strain relief for the cable. Placement of Tx / Rx Units Transmitter (Tx / Gray Unit) Place Tx unit on your hip - on the side of the guitar neck, or away from the guitar output. -
Page 8: Low Battery Led
Low Battery LED The low battery LED will turn on when the battery power is at a minimum, indicating 15 minutes or less left of battery life. When this occurs, follow the instructions under Changing Batteries. Changing Batteries To change batteries on either the Transmitter or Receiver, remove the cover plate on the back of the unit. -
Page 9: Changing Channels
Changing Channels DWG-1000 system components are linked at the factory. In the rare event that the Link LEDs on both the Transmitter and Receiver units continue to blink and fail to light solid, your DWG-1000 might be sharing channels with another wireless system. -
Page 10: Configuring Multiple Transmitters
Configuring Multiple Transmitters Up to 12 DWG-1000 TX transmitters can be associated, or bonded, to each But it’s only one Transmitter at a time! receiver. This is very cool for having your entire rack of axes hooked-up and ready to go; live or in the studio. etc... -
Page 11: Technical Specifications
• For technical assistance or support, please contact your local dealer or go to www.braceaudio.com for more information. Don't forget to register your product on-line too! Brace Audio 15600 NE 8th St, Suite B1, 287 Bellevue, WA 98008 made in the USA... -
Page 12: Declaration Of Conformity
All essential radio test suites have been carried out. _____________________________________________________________________ Product Description: Digital Wireless Guitar System Model: DWG1000 This declaration is issued under the sole responsibility of Brace Audio Corporation and, if applicable, their authorized representative(s) July 31, 2008 David Stokes, CEO/President... - Page 13 For Compliance Information ONLY, Contact: European Contact: Hyperactive Neukirchner Str. 18 65510 Hunstetten Germany USA Contact: Brace Audio Corporation 15600 NE 8th St. Suite B1, 287 Bellevue, WA 98008 Notified Body: Eurofins ETS Product Service GmbH Storkower Strasse 38c D-15526 Reichenwalde b. Berlin...
-
Page 14: Usage Notice
DWG-1000 are low. The user should in no way try to alter the radio settings as provided by Brace Audio. Changes or modifications not expressly approved by Brace Audio could void the user's authorization to operate the equipment. - Page 15 FCC Notice (United States): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
-
Page 16: Warranty
Brace Audio Corporation has been advised of the possibility of such damages. In no event will Brace Audio Corporation’s liability exceed the amount paid by you for the product from direct, indirect, special, incidental, or consequential damages resulting from the use of the product, its accompanying accessories, product packaging, or its documentation.