Zephyr Cypress AK7836ASX Use And Installation Manual
Cypress
Hide thumbs
Also See for Cypress AK7836ASX:
- Installation and use manual (19 pages) ,
- Use, care and installation manual (19 pages)
Related Manuals for Zephyr Cypress AK7836ASX
Summary of Contents for Zephyr Cypress AK7836ASX
- Page 1 Cypress AK7836ASX AK7842ASX AK7848ASX INTENDED FOR OUTDOOR COVERED PATIO OR LANAI AREA. Model number: Serial Number: Date of Purchase: Sales Dealer: APR14.0201 © Zephyr Corporation READ AND SAVE THESE INSTRUCTIONS...
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options .......................... Electrical ................. Mounting the Range Hood ........Single and Dual Internal Blowers ......Remote Blower Preparation ........FEATURES & CONTROLS Touch Controls .............
- Page 4 www.zephyronline.com READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
- Page 5 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to Electrical Diagram on product. and install appropriate connector if necessary. AK7836ASX, 70 Watts, 0.6 Amps AK7842ASX, 70 Watts, 0.6 Amps AK7848ASX, 105 Watts, 0.9 Amps AC power listed above is for hood with lights only.
- Page 6 M4 x 16 (4) Wire Caps (3) PARTS NOT SUPPLIED - Ducting, conduit and all installation tools AK7836ASX - 34” x 3/4” x 4” - Duct Cover Accessory AK7842ASX - 40” x 3/4” x 4” - Outdoor Hood Cover Accessory...
- Page 7 Equivalent number Equivalent number Duct pieces Duct pieces T otal length x used length x used T otal 3-1/ 4” x 10” 1 Ft. 6” Round 30 Ft. Rect., wall cap straight with damper 6” Round, 1 Ft. 6” Round, 30 Ft.
- Page 8 www.zephyronline.com Minimum mount height between range top to hood bottom should be no less than 30”. Maximum mount height should be no higher than 12”* 36”. It is important to install the hood at the proper mounting height. Hoods mounted too low could 18"...
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Some Ducting Options Roof Pitch w/ External Flashing & Cap Blower Side wall cap w/ gravity damper...
- Page 10 www.zephyronline.com Marine Grade 316S Body 12” ” 3/16 *10 ” ” ” 5/16 ” 1/16 ” 2” 5/16 5 9/16” ” ” 9/16 11/16 ” 7/16 18” elec 4” blwr 27” *10” transition used with dual, external and in-line blowers. side ”...
- Page 11 ELECTRICAL WARNING how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances. Electrical Supply: This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse.
- Page 12 4. Mark center line of wood board and align top of board with line B. Wood Board Dimensions AK7836ASX - 34” x 3/4” x 4” 30” AK7842ASX - 40” x 3/4” x 4” AK7848ASX - 46” x 3/4” x 4”...
- Page 13 CBI-600B AND PBI-1100A BLOWER INSTALLATION 1. Position blower plate over bracket on inside 2. Connect male end of blower wire to female plug back of hood and pivot up. Secure plate to hood 3. Single Blower – Connect 6” round duct work to blower collar.
- Page 14 www.zephyronline.com CBE-1000 EXTERNAL OR PBN-1000A IN-LINE BLOWER INSTALLATION 2. Install threaded end of external blower wiring 1. Place 10” round adapter on top of hood and through external blower wiring knock out round duct work to 10” round adapter. located inside the hood. 3.
- Page 15 Lights On/Off Adjust Blower Level (2 Speeds) Light On/Off By pressing , the light is switched On and Off. is on, is off. Blower Speed Selection The 2 speed levels are selected by switching to for level one and for level two. Switching the rocker switch to middle will turn off the blower.
- Page 16 30 days or more often depending on cooking habits. using hood. Hood Model: Part No. Qty. to Order. AK7836ASX 50210009 AK7842ASX 50210009 AK7848ASX 50210009 CAUTION: If this hood is installed in a salt water area (e.g.
- Page 17 Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees, stops and falls out. diameter of the bulb or use a rubber/latex glove and turn counter clockwise. For Zephyr part numbers please turn to page 17 of the manual.
- Page 18 www.zephyronline.com TROUBLESHOOTING PROCEDURES FOR CYPRESS Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2.
- Page 19 DESCRIPTION PART # Replacement Parts Optional Accessories Single Internal Blower CBI-600B Dual Internal Blower PBI-1100A External Blower CBE-1000 In-Line Blower PBN-1000A To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368...
- Page 20 Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or work- manship as follows:...