Page 3
SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........5 Mounting Height & Clearance ........ 6 Ducting Options ............Specifications ............... Electrical ................. Mounting the Range Hood ........10 Single and Dual Internal Blowers ......11 Remote Blower Preparation ........1 2 FEATURES &...
Page 4
READ AND SAVE THESE INSTRUCTIONS '_,i'_,i ' _,_ _ ,:,,,_,_/J y ,,y ..... WARNING TO REDUCE THE RiSK OF FiRE OR ELECTRIC SHOCK, DO NOT USE THiS FAN WiTH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
Page 5
WARNING TO REDUCE THE RiSK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION To reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within wails, ceilings, attics, crawl spaces or garages. OPERATION Always leave safety grilles and filters in place.
Page 7
Duct pieces Equivalent number Equivalent number Duct pieces length x used Total ..........................!e_used Total 3-114"x10" 1 Ft. 6" Round 30 Ft. Rect., wall cap straight with damper • oun i: .... O•R ........" Round, 1 Ft. straight roof cap 7"-I0"...
Page 8
Minimum mount height between range top to hood bottom should be no less than 30". Maximum mount height should be no higher than 1 "* 36". It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire hazard;...
WARNING FiRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape. Some Ducting Options Roof...
Page 10
Marine Grade 316S Body 12" 13 3/16" "10" 2 5/16" 1 1/8" 1 2 1/16" 2" 4 5/16" _ 2 11/16" 9/16" ,I 8 9/16" I 6 7/16', £ 18" elec 4,, I blwr 27" "10" transition used with dual, external and in-line blowers.
Page 11
ELECTRICAL WARNING All Electrical work must by performed by qualified electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances.
Page 12
CAUTION: At least two installers are required due to the weight and size of the hood. 1. Measure distance from range top to hood bottom (30" rain) Level and mark line A. wood board Plum and mark center line. 12 3/8" 3.
CBI-600B AND PBI-II00A BLOWER INSTALLATION Connect male end of blower wire to female plug 1. Position blower plate over bracket on inside in the hood. (plug is located inside the hood back of hood and pivot up. Secure plate to hood behind the control panel) with (2) 10x3/16"...
Page 14
CBE-1000 EXTERNAL OR PBN-1000A IN-LINE BLOWER INSTALLATION ,6_A 1. Place 10" round adapter on top of hood and Install threaded end of external blower wiring secure with (4) M4x8 screws. Connect 10" through external blower wiring knock out located inside the hood, round duct work to 10"...
Page 15
_:_ Lights On/Off Adjust Blower Level (2 Speeds) O Light On/Off I,.,, ,,I.,,t By pressing the light is switched On and Off. I is on, O is off. Blower Speed Selection for level two. The 2 speed levels are selected by switching for level one and Switching...
SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouring pads which will scratch and damage surface. Do not use products containing chlorine bleach or orange cleaners. For heavier soil use liquid degreaser. After cleaning, you may use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless...
Page 17
If bulbs are difficult to turn due to prolonged use, firmly attach a glass suction cup approximately the diameter of the bulb or use a rubber/latex glove and turn counter clockwise. Replacement bulbs are available at specialty lighting stores. Purchase type MR16 (GU-10) 35W halogen. For Zephyr part numbers please turn to page 17 of the manual.
TROUBLESHOOTING PROCEDURES FOR CYPRESS Issue Cause What to do 1. Make sure the circuit breaker and the unit's After installation, The power source is not turned ON. the unit doesn't power is ON. work. The power line and the cable locking connector 2.
Need help?
Do you have a question about the Cypress AK7848ASX and is the answer not in the manual?
Questions and answers