Zephyr Cypress AK7836ASX Installation And Use Manual
Zephyr corporation cypress use, care, and installation guide
Hide thumbs
Also See for Cypress AK7836ASX:
- Use, care and installation manual (19 pages) ,
- Use and installation manual (20 pages)
Related Manuals for Zephyr Cypress AK7836ASX
Summary of Contents for Zephyr Cypress AK7836ASX
- Page 1 Cypress AK7836ASX AK7842ASX AK7848ASX INTENDED FOR OUTDOOR COVERED PATIO OR LANAI AREA. Model number: Serial Number: Date of Purchase: Sales Dealer: AUG08.0101 © Zephyr Corporation READ AND SAVE THESE INSTRUCTIONS...
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE LIST OF MATERIALS INSTALLATION Ducting Calculation Sheet Mounting Height & Clearance Ducting Options Specifi cations Electrical Mounting the Range Hood Single and Dual Internal Blowers Remote Blower Preparation FEATURES & CONTROLS Touch Controls MAINTENANCE Cleaning and Filter Removal Lights TROUBLESHOOTING LIST OF PARTS AND ACCESSORIES...
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
- Page 5 WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. OPERATION Always leave safety grilles and fi...
- Page 6 MODELS: AK7836ASX, AK7842ASX, AK7848ASX PARTS SUPPLIED 1 - Hood 3 - Baffl e fi lters (4 for AK7848ASX) 2 - Halogen light bulbs (3 for AK7548ASX) (pre-installed) 1 - 10” round transition adapter (for dual internal and external blowers) 1 - External blower wiring (for external and in-line blower) 1 - Hardware package HARDWARE PACKAGE CONTENTS Suction Cup (1)
- Page 7 Equivalent number Duct pieces length x used 3-1/ 4” x 10” 1 Ft. Rect., straight 6” Round, 1 Ft. straight 7”-10” Round, 1 Ft. straight 3-1/ 4” x 10” 15 Ft. Rect.90 elbow 3-1/ 4” x 10” 9 Ft. Rect.45 elbow 3-1/ 4”...
- Page 8 12”* 18" Min 30" - Max 36" 36" *shown with 12" duct cover DUCTING A minimum of 6” round or 3-1/4” x 10” rectangular duct must be used to maintain maximum air fl ow effi ciency for single blower and 10” round duct for dual, in-line, and external blowers.
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver Tape or Duct Tape. Some Ducting Options Roof Pitch w/ Flashing &...
- Page 10 Marine Grade 316S Body ” 3/16 ” ” 5/16 5 9/16” ” 9/16 ” 7/16 ” 1/16 2” ” 11/16 elec 4” blwr ” (36”) 15/16 ” (42”) 15/16 ” (48”) 15/16 front www.zephyronline.com 12” *10 ” 5/16 18” 27” *10”...
- Page 11 ELECTRICAL WARNING All Electrical work must by performed by qualifi ed electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances.
- Page 12 CAUTION: At least two installers are required due to the weight and size of the hood. 1. Measure distance from range top to hood bottom (30” min) Level and mark line A. 2. Plum and mark center line. 3. Mark mounting height line B. (12 3/8” from line A) (This is the top of the board used to hang the hood) 4.
- Page 13 CBI-600B AND PBI-1100A BLOWER INSTALLATION 1. Position blower plate over bracket on inside back of hood and pivot up. Secure plate to hood with (2) 10x3/16” screws. (blower pictured is a PBI-1100A) 3. Single Blower – Connect 6” round duct work to blower collar.
- Page 14 CBE-1000 EXTERNAL OR PBN-1000A IN-LINE BLOWER INSTALLATION 1. Place 10” round adapter on top of hood and secure with (4) M4x8 screws. Connect 10” round duct work to 10” round adapter. 3. Place cap over threaded end of external blower wiring and secure by turning clockwise.
- Page 15 Light On/Off By pressing , the light is switched On and Off. Blower Speed Selection The 2 speed levels are selected by switching to Switching the rocker switch to middle Lights On/Off Adjust Blower Level (2 Speeds) is on, is off. for level one and will turn off the blower.
- Page 16 SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouring pads which will scratch and damage surface. Do not use products containing chlorine bleach or orange cleaners. For heavier soil use liquid degreaser. After cleaning, you may use non-abrasive stainless steel polish/ cleaners, to polish and buff out the stainless luster and grain.
- Page 17 If bulbs are diffi cult to turn due to prolonged use, fi rmly attach a glass suction cup approximately the diameter of the bulb or use a rubber/latex glove and turn counter clockwise. Replacement bulbs are available at specialty lighting stores. Purchase type MR16 (GU-10) 35W halogen. For Zephyr part numbers please turn to page 17 of the manual.
- Page 18 TROUBLESHOOTING PROCEDURES FOR CYPRESS Issue Cause After installation, 1. The power source is not turned ON. the unit doesn’t work. 2. The power line and the cable locking connector is not connecting properly. 3. The switch board and control board wirings are disconnected.
- Page 19 DESCRIPTION Replacement Parts Light Bulb MR16 (GU10) 35W (each) Baffl e Filter (each) Optional Accessories Single Internal Blower Dual Internal Blower External Blower In-Line Blower Vinyl Cover (36”) Vinyl Cover (42”) Vinyl Cover (48”) 12” Duct Cover (36”) 12” Duct Cover (42”) 12”...