Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
Single-Stud/Dual-Stud
Short-Throw Projector Wall Mount
Model: EST100/EST200
NORTH AMERICA
EUROPE
3130 East Miraloma Avenue
Swallow House,
Anaheim, CA 92806 USA
Shilton Industrial Estate,
USA and Canada
Shilton, Coventry, England CV79JY
Phone: 1-800-368-9700
Phone: +44 (0) 2476 614700
Fax: 1-800-832-4888
Fax: +44 (0) 2476 614710
Other Locations
Phone: (001) 714-632-7100
Fax: (001) 714-632-1044
9530-011-001-00
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Premier Mounts EST100
Summary of Contents for Premier Mounts EST100
-
Page 1: Heading
INSTALLATION INSTRUCTIONS Single-Stud/Dual-Stud Short-Throw Projector Wall Mount Model: EST100/EST200 NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House, Anaheim, CA 92806 USA Shilton Industrial Estate, USA and Canada Shilton, Coventry, England CV79JY Phone: 1-800-368-9700 Phone: +44 (0) 2476 614700 Fax: 1-800-832-4888... -
Page 2: Table Of Contents
THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE. PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR... -
Page 3: Installation Tools
Level Drill Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation. If there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700. EST100/EST200 Hardware Projector Arm... -
Page 4: Features
EST100/EST200 Features The Single-Stud/Dual-Stud Short-Throw Projector Wall Mount (EST100/EST200) is a simple and elegant tool for mounting a wide variety of short-throw projectors. Its design allows you to use the same mount even if you need to replace the pro- jector with a different model. -
Page 5: Determining The Installation Height
This measurement will be listed in the Users Manual. Center of the lens to the top of the projector bracket. If single-stud EST100, add 5.14˝ to the calculated total. If dual-stud EST200, add 1.9” to the calculated total. Ground This total distance will be the location for the lower mounting point. -
Page 6: Wood Stud Installation
THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION. Are you installing the single-stud EST100 or the dual-stud EST200? If EST100, continue to the “EST100 Installation” section below. If EST200, go to the “EST200 Installation” section on page 8. - Page 7 Use two (2) M5 x 10mm security screws to attach the projector arm cover plate to the projector arm. Go to the “Throw Distance Calculation” section on page 10. Wood stud not shown Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 7...
- Page 8 (2) lower mounting points. Back Plate Step 4 Once the mounting points have been marked, use a Drill Marking ⅛˝ drill bit and portable drill to drill the pilot holes. Page 8 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions...
- Page 9 The elongated mounting slots in the back plate allow some lateral shift for precise adjustments against the studs. Proceed to the “Throw Distance Calculation” section on page 10. Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 9...
-
Page 10: Throw Distance Calculation
(X - Y + Z) arm assembly. Please make note of this measurement. The EST100/EST200 can be also used as a wall-mounted standard projector mount as well as a short throw projector mount. Align the projector facing the opposite direction... -
Page 11: Attaching The Mount Carriage
Depth Plus 1/8” Allowance or Toothpick or Toothpick Mark Mark If your projector has a single mounting point, skip to the “Single Mounting Point Installation” section on page 14. Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 11... -
Page 12: Multiple Mounting Point Installation
¯ When the desired position is achieved, tighten the mounting screws to the projector and then tighten the hex head leg screws with the M5 Allen wrench. Page 12 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions... - Page 13 If the M6 square nut is not aligned with any slot, you can use any thin implement, such as a toothpick, to nudge it into alignment. Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 13...
-
Page 14: Single Mounting Point Installation
Do not overtighten the ¼-20 x screw. ″ Proceed to the “Attaching the Mount Carriage to the Projector Arm” section on page 15. Page 14 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions... -
Page 15: Attaching The Mount Carriage To The Projector Arm
(1) M5 x 10mm security screw to tighten the mount carriage in place. M5 x 10mm Security Screw Proceed to the “Cable Routing (Optional)” section on page 16. Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 15... -
Page 16: Cable Routing (Optional)
Securing the Projector (Optional) Your EST100/EST200 includes one (1) Security Barrel which can provide additional theft deterrence for your projector. Shown below are two examples of how you can use the security barrel to make your projector installation more secure: the PCB-CSL1 Security Cable (sold separately) or padlock (combination or keyed;... -
Page 17: Mount Adjustment
Technical Specifications All measurements are in inches(mm). 30.35 1.81 6.18 3.25 8.60 2.00 EST-100 SHORT THROW SINGLE STUD 17.50 16.00 Ø1 3.79 12.00 7.64 4.23 EST-200 SHORT THROW DOUBLE STUD Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 17...
Need help?
Do you have a question about the EST100 and is the answer not in the manual?
Questions and answers