Page 1
INSTALLATION INSTRUCTIONS Single-Stud/Dual-Stud Short-Throw Projector Wall Mount Model: EST100/EST200 NORTH AMERICA 1321 S. State College Blvd Fullerton, CA 92831 USA USA and Canada Phone: 1-800-368-9700 Fax: 1-800-832-4888 Other Locations Phone: (001) 714-632-7100 Fax: (001) 714-632-1044 9530-011-001-0X Rev.1...
THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE. PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR...
Level Drill Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation. If there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700. EST100/EST200 Hardware Projector Arm...
THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION. Are you installing the single-stud EST100 or the dual-stud EST200? If EST100, continue to the “EST100 Installation” section below. If EST200, go to the “EST200 Installation” section on page 8. EST100 Installation Step 1...
Page 5
(2) lower mounting points. Back Plate Step 4 Once the mounting points have been marked, use a ⅛˝ drill bit and portable drill to drill the pilot holes. Drill Marking Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 5...
Page 6
The elongated mounting slots in the back plate allow some lateral shift for precise adjustments against the studs. Proceed to the “Throw Distance Calculation” section on page 10. Page 6 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions...
If your projector has a single mounting point, skip to the “Single Mounting Point Installation”. Small Straw Depth Plus 1/8” Allowance Small Straw Depth Plus 1/8” Allowance or Toothpick Mark or Toothpick Mark Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 7...
Raise the mounting legs by rotating the leveling barrel clockwise. When the desired position is achieved, tighten the mounting screws to the projector and then tighten the hex head leg screws with the M5 Allen wrench. Page 10 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions...
Page 9
If the M6 square nut is not aligned with any slot, you can use any thin implement, such as a toothpick, to nudge it into alignment. Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 11...
″ Do not overtighten the ¼-20 x screw. Proceed to the “Attaching the Mount Carriage to the Projector Arm” section on page 15. Page 12 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions...
(1) M5 x 10mm security screw to tighten the mount carriage in place. M5 x 10mm Security Screw Proceed to the “Cable Routing (Optional)” section on page 16. Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 13...
Plastic Cover Route cables and wiring through the projector arm openings then out the back or bottom near the wall. Securing the Projector (Optional) Padlock PCB-CSL1 (Combination or Keyed) Page 14 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions...
What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective. If Premier Mounts chooses to replace a defective product or part, a replacement prod- uct or part will be shipped to you at no charge, but you must pay any related labor costs.
Need help?
Do you have a question about the EST200 and is the answer not in the manual?
Questions and answers