Direct Button Operation - Skyvue SKY5230 Owner's Manual

Direct Button Operation

INPUT
To view external source images, select the input source by
pressing INPUT on the remote control unit or on the TV.
1
Press INPUT.
• The INPUT list screen displays.
2
Press a / b or press INPUT again to select the
input source.
• An image from the selected source automatically
displays.
• Each time INPUT is pressed, the input source toggles.
• If the corresponding input is not plugged in, you cannot
change the input. Be sure to connect the equipment
beforehand.
Changing Channels
You can change channels in several ways.
Method 1
Using CH on the remote control unit or on the TV.
/
Method 2
Using remote control buttons 0-9, • (DOT).
Examples:
To select a 1 or 2-digit channel number (e. g., Channel 5):
Press 5 ENT.
To select a 3-digit channel number (e. g., Channel 115):
Press 1 1
To select a 4-digit channel number (e. g., Channel 22.1):
Press 2 2
Method 3
Selecting the program from Channel list.
1
Press INPUT on the remote control unit.
• The INPUT list displays.
2
Press to select "AIR" or "CABLE".
c / d
• The Channel list displays.
3
Press a / b to select the desired channel, and then
press ENTER.
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made if
there is no operation within a few seconds.
• If you push "0" by itself, nothing will happen.
• Complete the above steps within a few seconds.
• When you enter 0-9 and • (DOT), channel selection will be
made if there is no operation within a few seconds.
2012 SKYVUE
LC-80LE633U_70_60_52LE640U_C6400U_E.indb 20
5 ENT.
• (DOT) 1 ENT.
Changing Volume
You can change the volume by pressing VOL k / l on
the TV or on the remote control unit.
• To increase the volume, press VOL
• To decrease the volume, press VOL
Audio status
Output device
Fixed
Speaker Variable sound
• When "Output Select" is set to "Variable", the indicator on
the screen changes as shown below.
MUTE
Mutes the current sound output.
Press MUTE.
• " " will be displayed on the screen for 30 minutes, and
the sound is silenced.
• Within 30 minutes of pressing MUTE, mute can be
canceled by pressing VOL k / l or MUTE.
• Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.
Sleep Timer
Allows you to set a time when the TV automatically
switches to standby.
Press SLEEP.
• The remaining time displays when the sleep timer has been set.
• Each time you press SLEEP, the remaining time switches
as shown below.
Off 30 60 90 120
• When set, the time automatically starts counting down.
• If you want to adjust the sleep timer, you can press SLEEP
twice then change the time setting.
• When it is 5 minutes before the time expires, the remaining
time will start to keep appearing every minute.
• Select "Off" by pressing SLEEP to cancel the sleep timer.
• The TV will enter standby when the remaining time reaches 0.
FREEZE
Allows you to capture and freeze a moving image that
you are watching.
Press FREEZE.
• A moving image is captured.
• Press FREEZE again to cancel the function.
• When this function is not available, "No displaying still
image available." will display.
• The still image automatically goes out after 30 minutes.
• If you are using the freeze function and a broadcast
activates the V-CHIP BLOCK, the freeze function will be
canceled and a V-CHIP BLOCK message will appear.
• You can have the same settings by choosing "Freeze" on
the menu items.
k .
.
l
20
Output Select
Variable
Mute
60
20
2012/01/05 16:20:29