Explanation Of Fault Message Screens - Cumberland Stove Works MF3800 Operation And Maintenance Manual

caUtiOn
cUMBerLand StOVe WOrkS dOeS nOt recOMMend
BUrninG tHe StOVe On tHerMOStat MOde, eitHer
LOcaL Or reMOte, WHen BUrninG cOrn Or peLLet
BLendS. Spent aSH MateriaL WiLL BUiLd Up in tHe pOt,
inHiBit tHe iGnitOr FUnctiOn and caUSe a ViOLent
iGnitiOn.

expLanatiOn OF FaULt MeSSaGe ScreenS

OVER TEMP RESET
SWITCh
Allow the stove to cool then reset the high limit switch located
in the back of the unit. See FiGUre 1 On paGe 9.
NO PROOF OF FIRE
PUSh ON TO START
This means the stove went through the starting fire or electric
ignition sequences and did not heat up enough to satisfy the
proof of fire switch. Press ON button and restart the fire.
NOTE: There may be fuel burning in the stove while it shows
this screen. use extreme caution when manually relighting
a hot stove.
VACUUM FAULT
ChECK SEALS
This means that the stove doesn't have enough vacuum in
the firebox to run safely. Check that the fire box door is closed
and that the seal is in good working condition. Check the ash
pan door to make sure that the ash pan is firmly seated and
that the seal is in good working condition. To clear this fault
screen press the OFF button. If all doors are closed and sealed
properly and the problem persists please call your dealer or
CSW customer service for advanced troubleshooting.
W H e n p e r F O r M i n G a nY i n t e r n a L e L e c t r i c a L
Maintenance:
•
•
•
•
neVer SHUt tHe StOVe dOWn BY LeaVinG tHe HOpper
Lid Open. tHiS can caUSe an UnSaFe cOnditiOn.
aLWaYS USe tHe OFF BUttOn tO SHUt dOWn tHe StOVe.
aSHeS SHOULd Be pLaced in a MetaL cOntainer
WitH a tiGHt-FittinG Lid. tHe cOntainer SHOULd
Be pLaced On a nOn-cOMBUStiBLe FLOOr, WeLL
aWaY FrOM cOMBUStiBLe MateriaLS, pendinG FinaL
diSpOSaL. iF aSHeS are diSpOSed OF BY BUriaL in SOiL
Or OtHerWiSe LOcaLLY diSperSed, tHeY SHOULd Be
retained in tHe cLOSed cOntainer UntiL aLL cinderS
are nO LOnGer WarM.
This means that the stove has cooled to a point where it is
no longer heating the room. Make sure that the hopper has
fuel and that there are no obstructions that prevent fuel from
entering the firepot. Pressing the OFF button will send the
program to the ELECTRIC IgNITE screen. Pressing the SCROLL
button will send the program to the FUEL RANgE screen.
STOvE SHuTDOwN
To shut down stove operation press the OFF button at anytime.
This will cause the stove to stop feeding fuel into the firepot,
yet the combustion blower will continue to run exhausting all
smoke until stove is off.
iMPORTaNT: NEvER uNPLug YOuR STOvE wHiLE THERE iS
FuEL BuRNiNg iN THE STOvE. Doing so will cause combustion
blower to stop and smoke will enter the room through air
intake holes.
cumberlandStoveWorks.com
OPERATIOn AND MAINTENANCE MANUAL
WarninG
Moving parts inside of the cabinet May cause
inJUrY. dO nOt Operate Unit WitH paneLS reMOVed
Or Open.
hot parts. do not operate the unit with panel
Open.
risk of electric shock. disconnect power
BeFOre SerVicinG Unit.
in the event of coMponent failure, replace with
tHe OriGinaL FactOrY eqUipMent.
WarninG
caUtiOn
LOSS OF FIRE
OFF TO RESET
Model MF3800
page 17