Kenwood NX-700 Service Manual page 60

NX-700/700H
Item
Panel test mode
6. Low RSSI 1) Adj item: [An LRSSI]
at –118dBm Adjust: [✳✳✳]
adjust *7 2) Adj item:
[AnL LRSSI]→
[Analog [AnL' LRSSI]→
Narrow] [AnC LRSSI]→
[AnH' LRSSI]→
[AnH LRSSI]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
[Analog 1) Adj item: [Aw LRSSI]
Wide] Adjust: [✳✳✳]
2) Adj item:
[AwL LRSSI]→
[AwL' LRSSI]→
[AwC LRSSI]→
[AwH' LRSSI]→
[AwH LRSSI]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±3kHz)
[NXDN 1) Adj item: [Nv LRSSI]
Very Adjust: [✳✳✳]
Narrow] 2) Adj item:
[NvL LRSSI]→
[NvL' LRSSI]→
[NvC LRSSI]→
[NvH' LRSSI]→
[NvH LRSSI]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
*7: Because "RSSI at –118dBm adjust" of NXDN Narrow is adjusted by adjusting "RSSI at –118dBm adjust [Analog Narrow]", it is not necessary to
adjust "RSSI at –118dBm adjust" of NXDN Narrow.
7. High RSSI 1) Adj item: [An HRSSI]
at –80dBm Adjust: [✳✳✳]
adjust *8 2) Adj item:
[AnL HRSSI]→
[Analog [AnL' HRSSI]→
Narrow] [AnC HRSSI]→
[AnH' HRSSI]→
[AnH HRSSI]
SSG output:
–80dBm (22.4µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
60
ADJUSTMENT
Condition
PC test mode
equipment
1) Adj item: [Low SSG
RSSI (Narrow)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
1) Adj item: [Low
RSSI (Wide)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±3kHz)
1) Adj item: [Low
RSSI (Very Narrow)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output:
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
1) Adj item: [High SSG
RSSI (Narrow)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
SSG output:
–80dBm (22.4µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
Measurement
Test-
Unit Terminal Unit
ANT
Ext.SP
connec-
tor
ANT
Ext.SP
connec-
tor
Adjustment
Specifi cations /
Parts Method
[Panel test mode]
After input signal
from SSG, press
[ ] key to store the
adjustment value.
[PC test mode]
After input signal
from SSG, press
[Apply] button to
store the adjust-
ment value.
Adjust with the ana-
log signal.
[Panel test mode]
After input signal
from SSG, press
[ ] key to store the
adjustment value.
[PC test mode]
After input signal
from SSG, press
[Apply] button to
store the adjust-
ment value.
Remarks