Pin-Out Schemes - Cisco TelePresence System C20 Administrator's Manual

Telepresence system quick
Hide thumbs Also See for TelePresence System C20:
Table of Contents

Advertisement

Cisco TelePresence System Quick Set C20 / C20 Plus and Profiles using C20
Contents
Introduction

Pin-out schemes

This page gives an overview of the pin-out schemes for C20.
HDMI pin-out
External view of socket
Pin: 19
17
3
1
Pin: 18
16
4
2
RJ-45 Connector pin-out
Wiring diagram
1 8
standard cable
TOP
1
---------- 1
2
---------- 2
FRONT
3
---------- 3
1 8
6
---------- 6
Pin-out—VISCA™ camera control
RJ11, 8 pins shielded modular jack
Pin
Signal name
8
+12 V (presence 2.8 mA current source when
connected in daisy chain)
7
GND
6
TXD (out)
5
NC (no connect)
4
NC (no connect)
3
RXD (in)
2
GND
1
+12 V
D14637.06
Profile C20 and Quick Set C20 Administrator Guide TC4.2, July 2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Web interface
DVI-I pin-out
External view of socket
HDMI Pin-out
Pin Assignment
1
T.M.D.S. Data 2+
2
T.M.D.S. Data 2 Shield
3
T.M.D.S. Data 2 –
4
T.M.D.S. Data 1
5
T.M.D.S. Data 1 Shield
6
T.M.D.S. Data 1 –
7
T.M.D.S. Data 0
8
T.M.D.S. Data 0 Shield
9
T.M.D.S. Data 0–
10
T.M.D.S. Clock+
Pin-out—Camera cable
Signal name
RJ-45 pin
+12 V DC
1
GND
2
RX
3
TX
6
NC
4
NC
5
GND
7
+12 V DC
8
Advanced settings
Password protection
RS232 9 pin D-SUB pin-out
External view of socket
1
5
6
9
Pin Assignment
11
T.M.D.S. Clock Shield
Connector pin out
12
T.M.D.S. Clock–
13
CEC
14
Reserved (N.C. on device)
15
SCL
Signal type
16
SDA
Connector (codec)
17
DDC/CEC Ground
Input impedance
18
+5 V Power (max 50 mA)
Output impedance
19
Hot Plug Detect
Maximum input level
Maximum output level
Phantom power
Phantom power resistor pin "tip"
D-SUB pin
Phantom power resistor pin "ring
Twisted pair
4
1"
5
Frequency response
Twisted pair
2
Signal to Noise Ratio
3
Twisted pair
1
6
Twisted pair
5
4
74
Appendices
Appendices
Microphone, 3.5 mm Mini-Jack, 4 pole
Microphone control
Ground
Audio– Hot
Audio– Cold
Codec C20 audio connectors
Jack Mic input
RCA line input
Tip = Hot
Pin = Signal
Ring 1 = Cold
Shield = GND
Ring 2 = Mic. control
Shield = GND
Balanced
Unbalanced
Mini Jack 3.5 mm
Female RCA/phono
1.5 kOhm/leg
18k Ohm
-18.3 dBu +/-2 dB
9.0 dBu +/-2 dB
12 V +/-1 V
1.7 kOhm
1.7 kOhm
20 Hz-20 kHz +/-1 dB
20 Hz-20 kHz +/-1 dB
-85 dB
-95 dB
Administrator guide
Contact us
RCA pin-out
External view of socket
Signal
GND
RCA line output
Pin = Signal
Shield = GND
Unbalanced
Female RCA/phono
100 Ohm
8.2 dBu +/-2 dB
20 Hz-20 kHz +/-1 dB
-95 dB
www.cisco.com

Advertisement

Table of Contents
loading

This manual is also suitable for:

Telepresence system c20 plus

Table of Contents