Maintenance And Lubrication; Recommended Accessories - Craftsman 113.19771 Owner's Manual

maintenance and lubrication
M A I N T E N A N C E
W A R N I N G : F O R Y O U R O W N S A F E T Y , T U R N S W I T C H
" O F F "
A N D R E M O V E P L U G F R O M P O W E R S O U R C E
O U T L E T B E F O R E M A I N T A I N I N G O R L U B R I C A T I N G
YOUR SAW.
When you receive your new Craftsman radial saw, it
requires no lubrication. The radial saw has been partially
aligned and all bearings are lubricated and sealed for life. In
time, however, in order to keep your saw in perfect
working order and accurate, it will be necessary to lubricate
and realign. In fact, your radial saw needs more of a
c l e a n i n g t h a n a l u b r i c a t i o n .
Make sure the teeth of the ANTI KICKBACK pawls are
always sharp. Replace if not sharp.
LUBRICATION
Your saw is precision built and should be kept clean and
properly lubricated. Before describing the various points
w h i c h m a y p e r i o d i c a l l y r e q u i r e l u b r i c a t i o n , l T l S M O R E
I M P O R T A N T T O F I R S T M E N T I O N T H E V A R I O U S
P O I N T S W H I C H S H O U L D N O T B E L U B R I C A T E D .
N O L U B R I C A T I O N R E O U I R E D
Do not lubricate carriage ball bearings or motor bearings as
these are sealed ball bearings and require no added
lubrication.
Do not lubricate between radial arm cap and radial arm.
P E R I O D I C A L L Y L U B R I C A T E T H E S E P O I N T S
Use SAE No. 10W-30 automotive engine oil and refer to
Parts List for locations. Apply a few drops of oil along the
swivel latch pin and bevel index pin only if the pin has a
tendency to stick. Remove the left-hand carriage cover and.
use oil sparingly to prevent it from getting on the ball
bearings or races.
A light film of oil should be wiped on the face of the
column tube to lubricate the fit between the column tube,
and column support.
The thread on the elevation shaft assembly can be
lubricated through the oil hole in the center of the radial
arm cap.
CAUTION: Excessive oil at any location will attract
airborne dust particles and sawdust.
recom mended accessories
I T E M CAT.NO.
S t a n d
. . . . 9 - 2 2 2 O s
S t e e l L e s s
. . . : : . : : : : : . : : : : : :
C a s t e r s
. . . 9 - 2 2 2 0 8
K e y C h u c k
. 9 - 2 9 8 0
*Molding
Head Guard - 7-inch
. . .9-29524
*Molding
Head Guard - f-inch
. . .9-29523
R o t a r y S u r f a c e P l a n e r - C a r b i d e T i p
. . . . 9 - 2 9 5 1 3
S a n d i n g W h e e l - 8 - i n c h
. - . 9 - 2 2 7 4
Sanding Wheel - lO-inch
.9-22723
D u s t C o l l e c t o r . . . .
. . . . . 9 - 1 6 9 9 8
D u s t C o l l e c t o r . . . .
. . . . - 9 - 2 9 5 1 7
T a p e r J i g
. . . 9 - 3 2 3 3
*Satin
Cut Dado - 7-inch .
. .9-3257
* S a t i n C u t D a d o - 8 - i n c h .
. . 9 - 3 2 5 3
* M o l d i n g
H e a d S i n g l e C u t t e r
9 - 3 2 1 5
*Molding
Head Three Cutter
9-3221
Sanding Drum - 3-inch
. .5-25246
o Lower Retractable Guard .
9-29009
"Power
Tool Know How Handbook"
Radial Saw
9-2917
*Before purchasing
or using any of these accessories, read
and comply with additional safety instructions No. "(D)2"
on p. 4 of this manual.
.Meets OSHA Requirements as of 8-73.
The above recommended accessories are current and were
available at the time this manual was printed.
34