Craftsman 113.19771 Owner's Manual page 12

A L I G N M E N T P R O C E D U R E
IMPORTANT:
IN ORDER TO OBTAIN MAX'MUM CUTT'NG
ACCURACY, THE FOLLOWI'VG S'X STEPS
M U S T B E C A R E F U L L Y F O L L O W E D .
BECOME THOROUGHLY FAMILIAR WITH
THESE STEPS SO THAT YOU CAN ALWAYS
M A I N T A I N Y O U R S A W ' N P R O P E R
ALIGNMENT. THE ACCIJRACY OF EACH
ADJUSTMENT 'S ALWAYS DEPENDENT
UPON THE ACCIJRACY OF THE PRECEDING
ADJUSTMENT.
A f t e r
f o l l o w i n g t h e 6 s t e p a s s e m b l y a n d a l i g n m e n t
procedure and the Basic Saw operation section refer to
Trouble Shooting section if any difficulty is experienced
when performing any sawing operation.
S T E P O N E
N O T E : T h e f o l l o w i n g a d j u s t m e n t , p e r f o r m e d p r o p e r l y , w i l l
r e s u l t i n t h e w o r k t a b l e b e i n g p a r a l l e l t o t h e a r m .
A T T A C H I N G
A N D
L E V E L I N G T A B L E
M O U N T I N G
S U P P O R T C H A N N E L S .
1 . A t t a c h t a b l e m o u n t i n g s u p p o r t c h a n n e l s w i t h f o u r
s o u a r e h e a d 5 / 1 6 - 1 8 x 3 / 4 s c r e w s , l o c k w a s h e r s a n d f l a t
w a s h e r s a n d n u t s . P O S I T I O N S C R E W S l N C E N T E R O F
C H A N N E L S L O T S , f i n g e r t i g h t t o p e r m i t c h a n n e l s t o
" s l i p "
a g a i n s t t h e b a s e w h e n l e v e l i n g .
F R O N T
M O U N T R A I L S U 5 I N G
I N I ) E h U L E )
2 .
R e l e a s e b e v e l l o c k l e v e r , m o v e b e v e l i n d e x p i n t o l e f t
and rotate the motor to position saw blade, end of shaft
down. Lock bevel lock.
U n l o c k a n d h o l d a r m c o n t r o l l e v e r i n i n d e x r e l e a s e
p o s i t i o n a s s h o w n . P o s i t i o n a r m a g a i n s t l e f t s t o p
( a p p r o x i m a t e l y 5 0 o m i t e r ) . L o o s e n c a r r i a g e l o c k k n o b
a n d p o s i t i o n c a r r i a g e d i r e c t l y o v e r l e f t h a n d c h a n n e l '
N O T E : F o r s a f e t y r e a s o n s i n a c c o r d a n c e w i t h t h e U L
standard, stops have been provided to prevent 3600
r o t a t i o n o f t h e r a d i a l a r m .
S l i d e t h e a r b o r w r e n c h h a n d l e b e t w e e n e n d o f m o t o r
s h a f t a n d m o u n t i n g c h a n n e l t o a c t a s a f e e l e r g a u g e .
C a r e f u l l y l o w e r t h e m o t o r w i t h e l e v a t i o n c r a n k u n t i l
t h e e n d o f s h a f t i s j u s t t o u c h i n g t h e a r b o r w r e n c h . T h e
w r e n c h s h o u l d s l i d e b a c k a n d f o r t h w i t h o n l y s l i g h t
resistance. Tighten screw
"A".
N O T E : D o n o t c h a n g e t h i s e l e v a t i o n s e t t i n g u n t i l b o t h
l e f t a n d r i g h t h a n d t a b l e s u p p o r t c h a n n e l s h a v e b e e n
ad i usted .
4.
S Q U A R E H D . S C R E W
s/16-18 x 3/4
T A B L E M O U N T I N G
S U P P O R T C H A N N E L
F L A T W A S H E R
I N D E X R E L E A s T
P O S l T t O N
U N L O C K
L O C K
'i'\
5. Move arm and carriage to screw
"8"
and tighten
s u p p o r t i n t h e s a m e m a n n e r .
M o v e a r m a n d c a r r i a g e t o r i g h t h a n d s u p p o r t c h a n n e l
and level in the same manner you adjusted the left hand
s u p p o r t c h a n n e l .
Recheck both support channels to make sure that
tightening screws did not affect the accuracy of the
adjustment.
Elevate saw and place motor in vertical position to
p r o v i d e c l e a r a n c e f o r i n s t a l l a t i o n o f f r o n t ( w o r k ) t a b l e .
TABLE MOUNTING
S U P P O R T C H A N N E L
(LEFT HAND)
SCREW "8"
ARBOR WRENCH
8 .
t 2
SCREW