Craftsman 113.197511 Owner's Manual
  1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Saw
  5. 113.197511
  6. Owner's manual
Craftsman 113.197511 Owner's Manual

Craftsman 113.197511 Owner's Manual

10-1nch radial saw
Hide thumbs Also See for 113.197511:
Table of Contents

Advertisement

Quick Links

Save ThisManual
For Future Reference
owner's
manual
MODEL NO.
113.197411
10-1NCH ELECTRONIC
RADIAL SAW WITH
4_,-INCH CABINET
AND 2 DOORS
or
113.197511
10-1NCH ELECTRONIC
RADIAL SAW
WITH 44-1NCH CABINET
AND 2 DOORS AND
CASTERS
or
113.197611
10-1NCH ELECTRONIC
RADIAL SAW WITH
44-1NCH CABINET
AND 6 DRAWERS
Serial
Number
Model
:]nd serial numbers
may be found
on the left
hand
side of the base.
You shculd
record
both
model
and
serial number
in
a safe
place
for future
use.
FOR YOUR
SAFETY:
READ ALL
INSTRUCTIONS
CAREFULLY
r
I
113.19761
113.197411
SEARS / r.RRFT$ IVi R N
10-1NCH RADIALSAW
• assembly
• operating
• repair parts
\
Y\
Sold by SEARS, ROEBUCK AND CO., Chicago,
IL 60684 U.S.A.
Part No. SP5539
Printed in U.S.A,

Advertisement

Table of Contents
loading

Related Manuals for Craftsman 113.197511

Summary of Contents for Craftsman 113.197511

  • Page 1 FOR YOUR SAFETY: READ ALL INSTRUCTIONS CAREFULLY Sold by SEARS, ROEBUCK AND CO., Chicago, Part No. SP5539 113.19761 113.197411 SEARS / r.RRFT$ IVi R N 10-1NCH RADIALSAW • assembly • operating • repair parts IL 60684 U.S.A.

  • Page 2: Table Of Contents

    WARRANTY SERVICE NEAREST SEARS SERVICE This warranty applies only while this product This warranty gives you specific legal rights and you may also have other rights v,hich vary from state to state.

  • Page 3: Safety

    Read and follow all safety information and instructions. and in- Major Hazards Three major hazards are associated with using the radial arm saw for ripping. They are outfeed zone hazard, kickback, and wrong way feed. This section from hazards. Read the ripping...
  • Page 4 Safety Kickback Hazard Kickback is the uncontrolled the workpiece back toward the user du ring ripping. The cause of kickback is the binding or pinching of the blade in the workpiece. Several conditions can cause the blade to bind or pinch. When a workpiece kicks back, it could hit hard enough to cause internal organ in- juu, broken bones, or death.
  • Page 5 4. Keep floors clean and free of sawdust, wax and other slippery materials. 5. Keep work area well lighted cluttered. 6. Use saw only in dry area. Do not use in wet or damp areas. "ANSI Institute. blade and do not out of spinning.
  • Page 6 3. Unplug saw before doing maintenance, making adjustments, correcting ment, or changing blades. 4. Do not force saw. Use saw, blades and accessories only as intended. 5. tlave yellow key out and saw switched off before plugging in power cord.
  • Page 7 5. Do not overtighten blade collar could warp. 6. Do not turn saw on and off in rapid se- quence because cut- 7. Blade should stop within after saw is switched longer, the saw needs repair.
  • Page 8 Safety On-Product Safety Labels There are several safety labels on the saw. They alert the user to hazards the manual and remind the user how to avoid the hazard. Note where they are located Read and follow the safety information...
  • Page 9 On the side surface of the motor, from the infeed side when the saw is in a rip position, is this safety label to outfeed zone hazard: Near the saw handle is this safety alert you to thrown objects and to remind...

  • Page 10: Assembly

    Note: Before beginning assembly; that atl parts are included. If you are miss- ing any part, do not assemble saw. your Sears Service Center to get the missing part. Sometimes small parts can get lost in packaging material. Do not throw packajng until saw is put together.
  • Page 11 All models include: (When three are given, the first is for the door model easters, the second is for the door model without casters, and the third is for the drawer model.) v4" diam x _" long truss head screw (76/64/96) # 10 x v2"...
  • Page 12 Assembly A]! models include: slide arm support ck handle andle channel yoke plug (1) yellow key (1) blade wrench handwheel battery (1) battery cover (1) Only the door model drawer model ]lHllLltlLllltllllltB with casters include: #10 x _/8"long pan head screw (4) v4"...
  • Page 13 Only the door model with easters drawer model include: pin retainer foot rod (2) _caster Only the drawer model includes: drawer fastener (48) grease packet (1) Tools Needed for Assembly 7116" Wrench --___ 1/2" Wrench 9/16"Wrench 5/8" Wrench ex Wrench Medium Screwdriver Wrench Phillips...
  • Page 14 Note: This manual covers three models. Depending on the model saw, you will be in- structed to skip some steps, or do extra steps. The diffe.rences have to do with whether the cabinet ha.s doors or drawers, and whether or not it has casters.
  • Page 15 8. Put corner bracket in each corner, edges point up. Attach brackets sides of shelf: use two screws per bracket (insert screws through shelf); on end of each screw put washer, then nut, and wrench tighten. Note: Screws for short sides wilt be in,_tatted later.
  • Page 16 Assembly 2. Place one foot box so C-shaped ing faces you and closed side is on your left. 3. With threaded end of foot rod facing down, and smaller square opening you, put rod through top opening box, and slide half way down into box. 4.
  • Page 17 8. Pull foot lever forward until smooth pin sits in groove of foot box. Attach pin retainer to rear of foot box: use two screws (insert screws through two smaller holes of retainer; make sure smaller holes" are on top). 9.
  • Page 18 Assembly 3. Identify right side panel ter "R" stamped near center 4. Put right foot assembly inside edge of right side panel, so foot lever comes through "J" slot. Use two screws attach foot assembly to panel screws through ,fide panel). 5.
  • Page 19 5. Position rear support, with slide brack- inside right side panel, ets attached, short tabs point up, and solid surface faces front. 6. Attach rear support to side panel: two screws (insert screws through panel); on end of each screw put washer, then nut, and wrench tighten.
  • Page 20 Assembly 2. Identify right side panel by locating ter "R" stamped near center Position right side panel upright, slot is at bottom and facing you. 3. Put spacer inside front bottom side panel, so two holes face "J" slot and large hole rests on bottom 4.
  • Page 21 Attach Side Panels to Bottom Shelf 1. Set out: -eight v4" diam x v2" long truss head screws -eight vg'diam lock washers -eight W' diam hex nuts. 2. Put bottom shelf on floor so bottom surface faces you and angled end of lower support points up.
  • Page 22 Assembly 3. Attach spacer between each foot as- sembly and bottom shelf: use one screw per spacer (insert screw through foot as- sembly); on end of each screw put washer, then nut, and wrench tighten. Attach Skirts 1. Set out: -two skirts -ten v4"...
  • Page 23 Finish Cabinet (Only Door Models; Drawer Model: Go to "Complete ter Slide Assembly") 1. Set out: -upper support -center support -eight 1/4"diam x 1/2"long truss head screws -eight v4" diam lock washers -eight 1/4"diam hex nuts. 2. Rest center support on floor, solid sur- face down.
  • Page 24 Assembly Attach Doors 1. Set out: -two doors -two magnetic catches with stop plates -four #6 x _/2"long pan head plastite screws -four #6 x ya" long pan head screws -eight #10 x 1/2" long pan head plastite screws. 2. Put both doors face down on floor. At- tach magnetic catch to inside surface each door: use two #6 x v2"...
  • Page 25 2. Position rear support so short at top. Attach four slide brackets ter support (make sure solid surface support faces out): use four screws screws through slide brackets'); each screw put washer, then nut, and wrench tighten. 3. With solid surface on top, put upper support between...
  • Page 26 4. Set drawers aside for installation saw has been mounted. Attach Handwheel 1. Set out: -handwheel -#10 x 1/2"long pan head screw -# 10 lock washer -hex bushing. 2. Put hex bushing into opening of handwheel.
  • Page 27 I.ifl motor out of styrofoam base and set on center channel of saw. Remove table sections and fence. 6. Remove lock nut and flat washer motor support. 7. Slide bevel cncoder to top position will fit into notch in plate index on motor.

  • Page 28: Yoke

    4. Check and wrench tighten cabinet. 5. Put saw in location where it will be used. direc- 1/16"-_ bevel lock. so holes line on end all nuts in Cabinet...

  • Page 29: Foot

    WARNING Saw must slant slightly towards to keep blade carriage leveling forward. move unexpectedly Fingers, hand or arm could be cut off feet so by blade contact.

  • Page 30: Slide Arm

    Assembly Attach Slide Arm Supports 1. Set out: -two slide arm supports -four v4"diam x _" long pan head type AB screws -front table. 2. Identify top and bottom of table: top has countersunk holes. Place table bot- tom side up. 3.
  • Page 31 Snap remaining four U-clips over holes in sides of saw frame. 4. Put 17/64" in. diam x s_s '' out. diam washer on each W4" long mounting screw. 5. Stand table on edge. Put mounting...
  • Page 32 Assembly 9. Push slide arm supports until "L" brack- ets are flush with saw frame, then attach: use one V2"long truss head screw per sup- port (insert screw through "L" bracket); end of each screw put 17/d' in. diam x 9h6 out.
  • Page 33 Alignment and Adjustment Go to Alignment and Adjustment and follow all instructions. You cannot use the saw until it is aligned and ad- justed. It may be helpful to read the Con- trols Section before proceeding alignment and adjustment.

  • Page 34: Yellow

    Frees radial arm to move; locks in any desired pre-set 45 °, -45 ° On-off Switch Turns Allows saw to be switched Yellow Bevel lock Frees motor to rotate; locks in any desired pre-set 0°, 45°, -45 °, 90°, -90 °...
  • Page 35 F_nncti_ Frees carriage Rip l.ock radial arm; locks in position Swivel Lock Frees blade carriage between tions; locks in position Lock Operation/Comments Pull to move along Lock Pull to un]ock; push to lock to rotate Hold in unlocked rip and crosscut posi- while moving blade cwriage Controls...
  • Page 36 Operation/Comments protects against Lock in level position keeps crosscut; from fluttering until guard nose just clears acts as saw- top surface then lock in place See Ripping Set- Up for details and illustrations Turn counterclockwise loosen, clockwise Turn counterclockwise to move...

  • Page 37: Alignment And Adjustment

    Alignment and Adjustment WARNING Plugging for two could and severe spinning Do not plug in saw at any time during alignment Plug in saw only when used. Steps all steps Draw Line On Board Along This Edge to help you.
  • Page 38 Alignment and Adjustment 3. Feel for movement between and column support: place index finger of one hand against column and column port; use other hand to push end of rad- dial arm side to side and up and down. If there is no movement, no further justment is needed.
  • Page 39 5. Place framing square so long side is off rear edge of table, and short side just touches arbor shaft. Hold square grasp saw handle and pull blade carriage forward. Arbor shaft should just touch square at all points. If it does, no adjust- merit is needed.
  • Page 40 Alignment and Adjustment 6. If arbor shaft moves into or away from square, adjust radial arm: to move radial toward right, two socket head screws on right, tighten two screws on left. Note: and tighten screws equally. to move radial toward left, loosen two socket...
  • Page 41 2. Place square so long edge rests on table and short edge rests against blade surface, not on a tooth. 3. There should be no gap between and square. Note: Not all blades are per- fectly flat. Check different points along blade surface by making quarter turns and looking for gap each time.
  • Page 42 5. If there is a gap, adjust blade carriage: i) unlock swivel lock ii) loosen four adjusting blade carriage iii) grasp saw handle and move blade carriage until blade rests flush against square iv) lock swivel lock.
  • Page 43 5. If there is a gap, adjust rear carriage bearing (which is visible when you go to rear of saw and look up under radial arm-- carriage bearing rides on central i) hold bolt in place and loosen nut on...
  • Page 44 1. With blade still locked in out-rip tion, unlock rip lock and move blade car- riage to rear as far as it will go. 2. From front of saw, look up under radial arm to identify front carriage ing. With thumb and index finger, get pinch-hold inside groove of bearing.
  • Page 45 5. Place square so long side is on table under right side of blade, and short side hangs down vertically at front of saw. Push edge of square against fence 6. [x)wer radial arm until blade surface, not a tooth, just rests on square.
  • Page 46 Alignment and Adjustment Blade alignment and adjustment plet_ Note:/t is important that you peri- odically check alignment and adjustment insure accurate cuts and improve of cutting procedures. Be aware ment in one plane necessarily ment in other planes. Thus, the blade may be perfectly aligned for one tape of cut but...

  • Page 47: Battery

    1. Lock blade in in-rip position towards column, motor towards table front). 2. Lower blade until it just clears table. 3. Unlock rip lock, move blade back until it touches fence, and lock rip lock. 4. Loosen pawls/spreader wing nut and lower pawls/spreader to fence.

  • Page 48: Digital Display

    Digital Display The digital display runs on battery It tells the position of the blade and radial arm at the touch of a button. automatically turns itself off approximate- ly three minutes after a change in blade or arm position has been made.
  • Page 49 If there is still no display, try a new 6V alkaline battery or contact Sears. 4. When display shows correctly, tery cover into place. 5. Follow steps to align encoders zero reference points. To Replace Battery I.
  • Page 50 Digital Display Align Encoders Miter Encoder 1. Turn display on. 2. Lock radial arm at 0° miter. 3. Push MITER button. 4. Push REF SET button. Display will read: 5. Unlock miter lock, move radial arm to right until it snaps into pre-set position and lock miter lock.
  • Page 51 Bevel Encoder 1. Turn display on. 2. Lock radial arm at 0 ° miter. Lock motor at 0 ° bevel. 3. Push BEVEL button. 4. Push REF SET button. Display will read: 5. Support motor, unlock bevel lock, move motor counterclockwise snaps into pre-set indexed...
  • Page 52 Digital Display 2. Turn display on. 3. Push MITER button, then push REF SET button. Display will read: 4. Push BEVEL button, then push REF SET button. Display will read: 5. Push ELEV button, then push REF SET button. Display will read: Set Zero Reference Point For In- 1.
  • Page 53 4. Position blade 10" from fence, as measured to nearest tooth, and lock rip lock. 5. Push RIP button, then push REF SET button. Display should read: If it reads RIP instead of O-RIP, push RIP button, then push REF SET button. If it reads .00 instead of 10.00, push REF SET button.
  • Page 54 Electrical Connections Motor Specifications The AC motor used in the saw is a capacitor-start, non-reversible models covered in this manual following specifications: Rated H P. Max Developed H.P. 2.75 Voltage 120/240 Amperes 12/6 Hertz (cycles) Phase Single 345O Arbor Shaft Rotation...

  • Page 55: Electrical Connections

    When the protector activates, ately turn saw off, remove yellow key and wait for motor to cool. Push red re-set but- ton and listen/feel for click to indicate protector is re-set.
  • Page 56 240V operation: • heavy duty operation • either undersized or overloaded branch circuit serves the saw • power company cannot correct voltage situation. The following procedure to change...

  • Page 57: Crosscutting

    30° left miter position. Use right miter position whenever possible. v_ Do not cut freehand. You will not be able to control workpiece. ,/If blade jams, turn off saw, remove low key, then free blade. Straight cuts Rolling Carriage WARNING...
  • Page 58 5. Pull blade through fence and across table as far as it will go. 6. Push blade to rearmost position, hind fence, and turn saw" off. Keep hand on saw handle until blade stops spinning. in the A kerr is path.
  • Page 59 7. Push blade carriage to rearmost tion, behind fence, and turn saw off. Keep hand on saw handle until blade stops spinning. miter angle fence through diameter posi- Crosscutting...
  • Page 60 A length stop defines the cut length and ensures that all pieces will be cut to the same size.

  • Page 61: Ripping

    Ripping Defined Ripping is changing the width of a workpiece by cutting along its length. The workpiece is fed into the blade, which rotates in a fixed position, parallel fence, a set distance from the fence. A solid fence (no kerfs) serves as a guide for the workpiece.
  • Page 62 Do not set the blade closer than fence. The radial saw is the _a-ong such a narrow a cut. A band more appropriate for this type of cut. Ripping Safety The hazards associated...
  • Page 63 ¢ Keep hands away from outfeed ,/Push workpiece through to complete cut. Do not reach around to pull it. ,/If blade jams, turn saw off, remove low key, then free blade. Kickback Kickback is the uncontrolled propelling the workpiece back toward the user.
  • Page 64 _/Use ,I' Keep hands away from outfeed side. _/If blade jams, turn saw oft', remove yel- low key, then free blade. _ When cutting composition or other materials with one smooth and one rough side, put rough side up so pawls will be more likely to grab.
  • Page 65 Guard Nose Function The guard nose (hold down) must be set correctly during ripping to act as a partial barrier against the infeed side of the blade, to help keep the workpiece the table, and to deflect workpiece It must be lowered to just clear the workpiece.
  • Page 66 12" or more from fence 3. Make kerf: i) turn saw on ii) lower blade about vl6" into table iii) turn saw off and remove 4. Place workpiece parallel to and up against blade. Note: Workpiece tween blade and table front.
  • Page 67 8. "l't_rn saw off and wait foi" blade to stop spinning before touching workpieee. and support this Start _...
  • Page 68 Ripping Dado Blades, Molding See Accessories for information installation and use of dado blades and molding heads. Edging Edging is the use of a dado blade or mold- ing head in the horizontal position. advanced technique that requires ing head guard and a special fence. See Accessories for information stallation...

  • Page 69: Cutting Aides

    Cut to dimen- sions shown (inches). Fences Fences are required for all saw operations. To make a fence, use _" knot-free cut to table length. Do not use particle board or other composite materials cause they are not strong enough.
  • Page 70 Cutting Aides Auxiliary Fence Edging must use an auxiliary fence edging because you cannot completely cate the cutting tool behind a rip fence. Also, edging requires the use of a molding head guard (see Accessories). To make an auxiliary fence for edging, use 3/4"knot-free lumber.
  • Page 71 Clamp the featherboard to the front so that the angled edge of the feather- board is against the workpiece feed side of the blade. Do not featherboard against the cut off part feed side) of the workpiece. If clamped the outfeed side, the featherboard squeeze...

  • Page 72: Accessories

    1. Put inside loose collar on arbor shaft first, then install dado. Tighten blade nut directly against outside surface of dado. 2. Saw arbor is designed 13%"wide. Use of wider dado could cause dado and blade nut to spin off. To make or attach- larger than 13q6"wide cut, take several...
  • Page 73 0° miter. 4. If saw handle gets in way with radial arm locked at 0° miter, edging can be done at 30 ° left miter. In this position, ting tool can be located behind regular or auxiliary fence.
  • Page 74 JAMMED LOWER GUARD Accessories for this These accessories are designed saw. Read and follow instructions come with accessory. Item ... Auxiliary Table Cover ... see catalog Blades {10" with 5is" hole) ... see catalog Dado Blades Adjustable Dado 7"-24 tooth carbide ... see catalog 7"-32 tooth carbide ...

  • Page 75: Maintenance

    When new, the saw requires no lubrica- tion. The saw has been partially and all bearings are lubricated for life. In time, in order to keep the saw in good working order, it will be necessary to clean, lubricate and re-align.
  • Page 76 Maintenance Other areas to lubricate include: • cam surfaces of the rip lock assembly • between column tube and column support (Elevate radial arm to highest point, then wipe face of column light film of oil.) • foot assemblies, where through foot rods Adjustments...
  • Page 77 Bevel Lock If the motor can be moved by hand when the bevel lock is locked, if the lock offers little resistence when being locked, the space between the lock lever and cast- ing is different from approximately adjust according to step 10 in Mount Motor section of Assembly.

  • Page 78: Use Both Blade Wrenches

    Maintenance Lock If the blade carriage can be moved by pushing/pulling on the saw handle when the rip lock is locked, adjust: 1. Hold rip lock in unlocked position and tighten locknut one quarter turn. 2. Test adjustment: if carriage moves with difficulty, slightly loosen locknut;...

  • Page 79: Troubleshooting

    Push re-set button; listen and feel for click Check power line for correct volt- Vacuum motor Check that shaft turns freely by hand; if it doesn't, return to Sears Take saw to Sears for service Slow feed rate Replace with 15 amp slow-blow...
  • Page 80 Inaccurate Crosscuts not accurate at indexed miter positions Depth of crosscut varies from one side of workpiece to other Saw cuts at slight bevel Workpiece kerf rough with tooth marks from blade Blade tends to advance through workpiece too fast during...
  • Page 81 Adjust bevel lock for wear Adjust rip lock for wear CIean and lubricate track Adjust carriage bearings, then re- align saw Adjust rip lock Have Sears replace arm track Replace carriage bearing Tighten blade nut Take saw back to Sears for service...
  • Page 82 What to Do Install battery correctly Clean battery contacts Replace with 6V, size J battery Have electronics checked by Sears No action Set "0" reference points Clean battery contacts Have electronics checked by Sears Replace with 6V, size J battery Allow saw to warm above 32°F...
  • Page 83 Blank Page...

  • Page 84: Repair Parts

    Repair Parts PARTS LIST FOR CRAFTSMAN MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 10" ELECTRONIC 1 (SEE FIG. 6) _\15 (SEE FIG. 3 & 4) RADIAL SAW (SEE FIG. 8) FIGURE...
  • Page 85 PARTS LIST FOR CRAFTSMAN MODEL NOS. 113.197411 AND 113.197611 AND 113.197511 Always order by Part Number - Not by Key Number Part Description Table Boards Set (see Fig. 6) 806828-4 Screw, Pan Cross Type "T" 1/4-20 x 1-3/4 STD551012 * Washer, 17/64 x 5/8 x 1/32...
  • Page 86 Repair Parts PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197411 113.197611 113.197511 FIGURE...
  • Page 87 STD610803 815749-1 815865 815864 815649 60353 60339 817398-2 3540 Repair Parts RADIAL 113.197511 Description Base Assembly * Nut, Lock 1/2-13 Washer, Keyed Bearing Lift Shaft Gear, Bevel Gear, Pinion * Ring, Retaining 7/16 Nut, Elevation * Screw, Pan Rec. Hd Type "T"...
  • Page 88 Repair Parts PARTS LIST FOR CRAFTSMAN MODEL NOS. 10" ELECTRONIC 113.197411 AND 113.197511 1 (SEE FIG. 4) FIGURE RADIAL 113.197611...
  • Page 89 * Standard Hardware kern may be Purchased Locally. 1Stock Item may be secured Through the Hardware Department of Most Sears Retail or Catalog Order Houses. • Any attempt to repair this motor may result in unit misalignment and create a HAZARD unless repair is done by a qualified service technician.
  • Page 90 Repair Parts PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 FIGURE...
  • Page 91 63777 60438 815807 810214-3 STD3!5485 817181 815689 Repair Parts RADIAL SAW Description Nut, Square 5,;8-! 1 Knob, Swivel * Nut, Hex 1/4-20 Wrench, Adjustment w/Actuator * Screw, Pan Hd 1/4 20 x 1-1/2 * Washer, .630 x 1-1/8 x 3/32...
  • Page 92 Repair Parts PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 FIGURE...
  • Page 93 * Screw, Pan Rec. Hd STD600803 Type "T' #8-32 x 3/8 * Standard Hardware Item may be Purchased Locally. -I-Stock Item may be Secured Through the Hardware Department of Most Sears Retail or Catalog Order Houses. 10" ELECTRONIC 113.197611 FIGURE...
  • Page 94 Always order by Part Number - Not by Key Number * Standard Hardware Item may be Purchased Locally. 10" ELECTRONIC 113.197411 113.197611 FIGURE 6 - TABLE ASSEMBLY Part Description 815757 Table, Rear 815755 Table, Spacer 815758 Fence, Rip 818196-1 Table, Front RADIAL 113.197511...
  • Page 95 PARTS LIST FOR CRAFTSMAN MODEL NOS. 113.197411, Always order by Part Number - Not by Key Number FIGURE 7 - FOOT ASSEMBLY - MODEL 113.197511 & 113.197611 STD601103 * Screw, Pan Rec. Hd 815874 817116 815879 815871 STD541237 * Nut, Hex Jam 38-16...
  • Page 96 Repair Parts PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197411, 113.197511 AND 113.197611 (SEE FIG. (SEE FIG. 10} FIGURE 8...
  • Page 97 PARTS LIST FOR CRAFTSMAN MODEL NOS. 113.197411, 113.197511 AND 113.197611 Always order by Part Number - Not by Key Number FIGURE 8 - CABINET Part Description 60314 Screw, Truss Hd 1/4-20 x 1/2 815898 Skirt 44" 815892 Support, Center Rear...
  • Page 98 Repairs Parts PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197411, 113.197511 AND 113.197611 FIGURE...
  • Page 99 Hinge, Door 816274-1 Screw, Pan Hd Plastite 10-10 x 1/2 * Standard Hardware Item May Be Purchased Locally, • Moee1113.197511 Only 10" ELECTRONIC 113.197411, 113.197511 ASSEMBLY FOR MODEL 113.197411 AND 113.197511 Part 815882 815942 815993 815991 817150 815889 STD600603 816336 802392-36...
  • Page 100 Repairs Parts PARTS LIST FOR CRAFTSMAN MODEL NOS. 113.197411, 113.197511 AND 113.197611 Always order by Part Number - Not by Key Number FIGURE 10 - DRAWER * Standard 10" ELECTRONIC ASSEMBLIES FOR MODEL 113.197611 Part Description 815912 Drawer Assembly, 3"...
  • Page 101 64921 STD600603 64909 64951 64948 30582 507744 STD376116 64950 * Standard 10" ELECTRONIC 113.197511 AND 113.197611 11 - MOTOR ASSEMBLY Part Description Gasket Protector * Screw, Type 23 Pan Hd 6-32 x 3/8 Switch, Slide Screw, Flat Head Screw, Ground...
  • Page 102 * Screw, Pan Hd Type "T" 10-32 x 3/8 * Nut, Hex Jam 5/6-18 STD541231 Pawl 815815 * Standard Hardware Item may be Purchased Locally. 10" ELECTRONIC 113.197511 AND 113.197611 FIGURE 12 - GUARD ASSEMBLY Description STD581 O50 63270 816341...

  • Page 103: Index

    Set-Up Procedure Workpiece Position 62 Safety. Accessories Blade 7 Crosscutting General 3 Personal 5 Ripping 3, 62 Saw 6 Work Area 5 Workpieee Spreader Alignment 46 Function!Operation 36, 65 Straight Edge 71 Table Lock Function/Operation Wrong Way Feed 4, 64...

  • Page 104: And Co

    PARTNUMBER MODEL NUMBER 113.197411 ! 13 197511 ! 13,19761 / All parts listed may be ordered and most Sears stores. If the parts you need locally, your order will be electronically Repair Parts Distribution Center for handling. Form No. SP5539 simply contact and Co.

This manual is also suitable for:

113.197611113.197411

Table of Contents