Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ledj SPECTRA BATTEN12T3 EXTERIOR
Summary of Contents for Ledj SPECTRA BATTEN12T3 EXTERIOR
- Page 1 www.prolight.co.uk SPECTRA BATTEN 12T3 EXTERIOR (Order code: LEDJ259) User manual...
-
Page 2: Safety Instructions
Spectra Batten 12T3 Exterior Safety WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! CAUTION! INPUT VOLTAGE OF 100~240V SAFETY INSTRUCTIONS Every person involved with the installation, operation & maintenance of this equipment should: Be competent Follow the instructions of this manual CAUTION! TAKE CARE USING THIS EQUIPMENT! -
Page 3: Operating Determinations
Spectra Batten 12T3 Exterior Safety IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorised modification to the equipment. • Never let the power-cable come into contact with other cables. Handle the power-cable and all mains voltage connections with particular caution! •... - Page 4 Spectra Batten 12T3 Exterior Introduction Introduction Features • 12 x 3W tri-colour LEDs • Beam angle: 40 degrees • 0-100% dimming and variable strobe • DMX channels: 1, 3, 3, 4 or 5 selectable • Static colour, colour fade, colour change, colour mix, auto, master/slave and DMX modes •...
- Page 5 Spectra Batten 12T3 Exterior Operation Modes Operation modes Colour mix mode: To activate the units colour mix mode, press and hold the “M” button for 2 seconds to show “COL” on the LED screen. Now tap the “M” button to scroll through the three separate colours, red green and blue.
- Page 6 Spectra Batten 12T3 Exterior DMX Programme Charts DMX Mode To activate the units DMX mode, press and hold the “M” button for 2 seconds to show “0.01” on the LED screen and use the “UP” and “DOWN” buttons to set the first digit in the DMX address from 0 to 9.
- Page 7 Spectra Batten 12T3 Exterior DMX Programme Charts DMX Charts: 3 channel mode DMX chart (RGB): Channel Value Function 0-255 Red 0-100% 0-255 Green 0-100% 0-255 Blue 0-100% 3 channel mode DMX chart (function): 4 channel mode DMX chart: Value Channel Function 0-255 Red 0-100%...
-
Page 8: Dmx Linking
Spectra Batten 12T3 Exterior DMX Set up DMX-512: • DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN”... -
Page 9: Power Linking
Spectra Batten 12T3 Exterior DMX Set up Notice: • Be sure to follow figures 2 & 3 when making your own cables. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. -
Page 10: Troubleshooting
Spectra Batten 12T3 Exterior Trouble Shooting Problem Probable cause Solution Check that the power is switched No power to the fixture. on and cables are connected. One or more fixtures are completely dead. Contact your Prolight dealer. Internal fuse has blown. The controller is not connected. - Page 11 Spectra Batten 12T3 Exterior Trouble Shooting Problem Probable cause Solution Contact a technician for servicing Fixture black out suddenly The fixture is resetting the effect. if the problem persists. Allow the fixture to cool down. Fixture is too hot. Make sure that all air vents are not blocked.
Need help?
Do you have a question about the SPECTRA BATTEN12T3 EXTERIOR and is the answer not in the manual?
Questions and answers