Kirisun PT4200 Service Manual page 6

IC15 is a voice memory chip which stores the voice indication of
channels, and every time you change the channel, the speaker will
sound voice annunciation of the current channel number. Press
voice annunciation key will repeat the voice annunciation of the
current channel number.
If the voice annunciation function has been set, press
annunciation key in the stand by mode and the speaker will
sound voice annunciation of the current channel number. If turn on
the radio again with the voice annunciation
voice type will be changed. Repeat turning on the radio with the
voice annunciation key pressed, the voice type will change in the
sequence Chinese Male--- English Male--- Chinese Female ---
English Female ---- No Indication .
3.5 Power Supply
The radio is equipped with 7.4V, 1200mAh Li-Ion battery. The
battery supplies power directly to the transmitter amplifier circuit
(Q11, Q12) and the receiver amplifier (IC8). The power supply of
other circuits is the regulated 5V power.
IC12: 5V low voltage difference, micropower regulator, together
with Q10, and Q30 supply big current 5V power to the whole radio.
Q29: 5T switch, controlled by MCU.
5T: Supplies power for the front terminal of the transmitter.
Q31: 5R switch, controlled by MCU.
5R: Supplies power for the receiver RF amplification, mixing, IF
processing, audio signal processing.
Q32: 5C switch, controlled by MCU
5C: The 5V power controlled by power saving supplies power
for the frequency synthesizer.
3.6 MCU
Figure 3.9 MCU Diagram
MCU controls the working of each unit of the radio to realize all
the radio functions.
Connects with the PC
Accesses the radio status data
Controls PLL to generate the receiving and transmitting local
oscillation frequency.
Accesses the current channel status.
Controls the LED status indication
Controls the power supply of each location
Checks the action of each function key
Generates CTCSS signals
Generates DCS signals
DCS decoding
Squelch check and control
Controls the content of voice indication
Memorizer
Memorizes the radio channel data, CTCSS/DCS data, and
other data of function setting and parameter adjustment.
voice
CTCSS/DCS Encoding and Decoding
CTCSS/DCS signals generated by MCU (output form pin5) are
filtered at R155, R156, C242, and C243, and then sent to VCO and
key pressed, the
TCXO for modulation.
CTCSS/DCS signals from the receiver are sent to MCU(pin1)
for demodulation. MCU determines whether the signals contain the
same CTCSS/DCS as that set on the radio and decides whether to
turn on the speaker.
Power Adjustment
MCU P56 output is sent to APC part to control the transmitter
output power.
CTCSS
CTCSS (continuous tone control squelch system) is a squelch
control system modulated on carrier wave with continuous subaudio
frequency as pilot frequency. If a channel is set with CTCSS, only
when both the CTCSS of the receiver and that of the transmitter are
identical, communication is available, which avoids interference of
other signals.
39 groups of standard CTCSS frequency is available on the
radio, see Table 3.1.
CTCSS signals generated by MCU pass the low pass filter
consisting of RC to be filtered off the high frequency over 300Hz
and then are sent to VCO for modulation.
Table 3.1 CTCSS Frequency Table
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PT4200 SERVICE MANUAL
E2PROM AT24C08
.
FREQUENCY
(Hz)
67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
.
No
FREQUENCY
(Hz)
21
131.8
22
136.5
23 141.3
24 146.2
25 151.4
26 156.7
27 162.2
28 167.9
29 173.8
30 179.9
186.2
31
32 192.8
203.5
33
34 210.7
218.1
35
225.7
36
37 233.6
241.8
38
250.3
39
4