Honda Magna VF750C Service Manual page 128

N OTE
M a rk a l l pa rts d u ri n g d i sassembly so they can be re placed i n the i r ori g i n a l locations.
•
A l l bea ring inserts a re se l ect fitted a n d a re identified by co lor code. Select repl acement bea ri ngs from the code
•
ta ble ( page After i nsta l l i n g new bea rings, recheck them with plastigauge to verify the clea rance.
1 1 - 1 6) .
Apply m olybde n u m disu lfide o i l to the con necting rod/m a i n j o u rn a l bea rin gs, m a i n j o u rn a l a n d cra n kpi n .
•
Requisite Service
Refer to Service I nformation ( page
•
Procedure
Removal Order
Connecti ng rod bea ri ng cap n ut
( 1 )
Con necting rod bea ring ca p
(2)
Connecti n g rod/piston assem bly
(3)
Connecti ng rod bea ring
(4)
Cra n kshaft
(5)
Cra n kshaft main j o u rn a l bea ring
(6)
(7) Front ca m c h a i n tensioner s l i pper bolt
F ront ca m chain tensioner s l i pper
(8)
Rea r ca m chain tensioner s l i pper bolt
(9)
Rea r cam c h a i n tensioner s l i pper
( 1 0)
F ro nt/rear cam c h a i n s l i pper bolt
( 1 1 )
( ) F ront/rea r cam ch a i n s l i pper
1 2
Installation Order
Fro nt/rear cam cha i n s l i pper
( )
1 2
F ro nt/rear cam chain s l i pper bolt
( 1 1 )
Rea r ca m c h a i n tensioner s l i pper
( 1 0)
Rea r cam cha i n tensioner s l i pper bolt
(9)
Front ca m cha i n tensioner s l i pper
(8)
(7) F ront ca m chain tensioner s l i pper bolt
Cra n kshaft main journal bea ring
(6)
Cra n kshaft
(5)
Con necting rod bea ring
(4)
Con nect i n g rod/piston assembly
(3)
Connecti ng rod bea ring cap
(2 )
Con necting rod bea ring cap n ut
( 1 )
1 1 - 1 )
Q'ty
I nsta l lation is in the reverse order of remova l .
8
N OTE
4
Note the d i rectio n of the bea ring ca p.
•
CAUTION
4
Do not try to remove the connecting rod/piston as-
•
sembly from the bottom of the cylinder. The oil ring
will become wedged in the gap between the cylinder
liner and the upper crankcase.
Wi pe a l l o i l fro m bea ring seating a reas.
8
1
Wi pe a l l o i l from bea ring seating a reas.
8
1
1
1
1
2
1
1
Clean a n d apply a l ocki ng agent to the th reads.
2
1
Clea n a n d apply a l ocking agent to the threads.
1
1
Clean a nd apply a l ocking agent to the th reads.
1
NOTE
8
At insta l l ation, a l i g n the oi l h o l es between the cra n k-
•
c a s e a n d bea r i n g , a n d t h e b e a r i n g ta b s w i t h t h e
g roove i n the cra n kcase.
1
NOTE
8
At i n sta l l ation, a l i g n the o i l h o les betwee n the con-
•
necting rod and bea ring, a n d the bea ri n g tabs with the
g roove i n the con n ecti ng rod and beari n g ca p.
N OTE
4
Each connecti ng rod has an identification m a rk; " M L7-
•
F " (Front), " M L7-R" ( Rear).
At i n sta l l a t i o n , i n sta l l the c o n n e c t i n g r o d/ p i st o n
•
asse m bly with the o i l h o l e on the connect i n g rod fac-
ing opposite the rotati ng d i rection of the cra n kshaft.
4
N OTE
8
At i n sta l l ati o n , a p p l y e n g i n e o i l to the th rea d s a n d
•
seati ng su rface of the n ut.
Tig hten the n uts g ra d u a l ly and a lternate ly.
•
Crankshaft/Piston/Transmission
Remarks
1 1 - 5