Checking Brake Pedal Clearance; Checking Drive Belts; Checking And Replacing Fuses; Replacing A Fusible Link - Hyundai 2001 Santa Fe Owner's Manual

G180A01A-AAT
CHECKING BRAKE PEDAL CHECKING BRAKE PEDAL CHECKING BRAKE PEDAL CHECKING BRAKE PEDAL CHECKING BRAKE PEDAL
CLEARANCE CLEARANCE CLEARANCE
CLEARANCE CLEARANCE
2.95 in. (75 mm)
You need a helper to check the brake pedal
clearance. With the engine running, have your
helper press down on the brake pedal several
times and then hold it down with a force of about
110 lbs (50 kg, 490 N). The brake pedal clear-
ance is the distance from the top surface of the
brake pedal to the asphalt sheeting under the
floor mat.
If the brake pedal clearance is not within the
limits specified in the illustration, have it in-
spected by your Hyundai dealer and adjusted
or repaired if necessary.
6-14
DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE
G190A01A-AAT

CHECKING DRIVE BELTS

CHECKING DRIVE BELTS CHECKING DRIVE BELTS CHECKING DRIVE BELTS CHECKING DRIVE BELTS
V6
Power steering
Auto
tensioner
Generator
COMP
Eng.pulley
SSA6180A
Drive belts should be checked periodically for
proper tension and adjusted if necessary. At the
same time, belts should be examined for cracks,
wear, fraying or other evidence of deterioration
and replaced if necessary.
Belt routing should also be checked to be sure
there is no interference between the belts and
other parts of the engine. After a belt is re-
placed, the new belt should be adjusted again
after two or three weeks to eliminate slack
resulting from initial stretching after use.
G200A01A-AAT
CHECKING AND REPLACING CHECKING AND REPLACING CHECKING AND REPLACING CHECKING AND REPLACING CHECKING AND REPLACING
FUSES FUSES FUSES
FUSES FUSES
DOHC

Replacing a Fusible Link

Replacing a Fusible Link Replacing a Fusible Link Replacing a Fusible Link Replacing a Fusible Link
Power steering
Eng.coolant
0.30 ~ 0.48 in. 0.24~0.35 in.
Generator
COMP
Eng.pulley
G140D01Y/G140D02Y
A fusible link will melt if the electrical circuits
from the battery are ever overloaded, thus pre-
venting damage to the entire wiring harness.
(This could be caused by a short in the system
drawing too much current.) If this ever happens,
have a Hyundai dealer determine the cause,
repair the system and replace the fusible link.
The fusible links are located in a relay box for
easy inspection.
CAUTION: CAUTION:
CAUTION: CAUTION: CAUTION:
When replacing a fusible link, never use When replacing a fusible link, never use When replacing a fusible link, never use When replacing a fusible link, never use When replacing a fusible link, never use
anything but a new fusible link with the anything but a new fusible link with the
anything but a new fusible link with the anything but a new fusible link with the anything but a new fusible link with the
same or lower amperage rating. Never use a same or lower amperage rating. Never use a same or lower amperage rating. Never use a
same or lower amperage rating. Never use a same or lower amperage rating. Never use a
piece of wire or a higher-rated fusible link. piece of wire or a higher-rated fusible link. piece of wire or a higher-rated fusible link. piece of wire or a higher-rated fusible link. piece of wire or a higher-rated fusible link.
This could result in serious damage and This could result in serious damage and This could result in serious damage and This could result in serious damage and This could result in serious damage and
create a fire hazard. create a fire hazard. create a fire hazard. create a fire hazard. create a fire hazard.
Bad Good
G200A01Y