1. Manuals
  2. Brands
  3. Britax Manuals
  4. Car Seat
  5. 7200/A/2010
  6. Instructions for installation and use manual

Britax Safe-n-Sound 7200/A/2010 Series Instructions For Installation And Use Manual

Convertible child restraint featuring ahr tilt & adjust
Hide thumbs Also See for Safe-n-Sound 7200/A/2010 Series:
Table of Contents

Advertisement

Quick Links

See also: Instructions for Use Manual
Convertible Child Restraint
Rearward Facing
For use with children
up to approximately 12 months.
IMPORTANT: KEEP THIS BOOKLET IN THE PLACE PROVIDED ON THE CHILD RESTRAINT
Featuring AHR Tilt & Adjust™
Series No. 7200/A/2010
Forward Facing.
For use with children from
approximately 12 months to
approximately 4 years of age.

Advertisement

Table of Contents
loading

Related Manuals for Britax Safe-n-Sound 7200/A/2010 Series

Summary of Contents for Britax Safe-n-Sound 7200/A/2010 Series

  • Page 1 Convertible Child Restraint Featuring AHR Tilt & Adjust™ Series No. 7200/A/2010 Rearward Facing Forward Facing. For use with children For use with children from up to approximately 12 months. approximately 12 months to approximately 4 years of age. IMPORTANT: KEEP THIS BOOKLET IN THE PLACE PROVIDED ON THE CHILD RESTRAINT...
  • Page 2 CAREFULLY READ ALL THE INSTRUCTIONS FOR INSTALLATION. IN THE EVENT OF DOUBT ABOUT HOW TO USE THE METHOD OF INSTALLATION, CONSULT BRITAX CHILDCARE OR AGENT OR A CHILD RESTRAINT SPECIAL FEATURES: FORWARD-FACING FITTING STATION AUTHORISED BY A RELEVANT TRANSPORT AUTHORITY OR, IN NEW ZEALAND, THE AGENT FOR THE VEHICLE.
  • Page 3 • Use the restraint exactly as shown in the instructions. • The restraint should not be purchased or sold as a second hand item. It is recommended not to use child restraints older that 10 years as the protection in an accident may be reduced. • Fit the restraint firmly to the car seat. • The restraint is not intended to be a substitute baby cot or bed. It is only designed to enable safe • Fit the harness firmly to the child. transportation of children in motor vehicles. Do not leave a baby in the restraint for long periods •...
  • Page 4 SHOULDER HEIGHT MARKERS SHOULDER HEIGHT MARKERS A GROWING CHILD THE NEXT STEP Newborn (Rearward Facing) Shoulder height markers are provided on this restraint for a visual indication that the child is safe to Shoulder height ride in this restraint. Do not turn to forward-facing until the child's shoulder's reach the lower marker. label (hidden) Rearward Facing Label A...

  • Page 5: Shoulder Height Markers

    SHOULDER HEIGHT MARKERS THE NEXT STEP SPECIAL FEATURES: REARWARD-FACING For the next child restraint choose Convertible Booster To be used only in a rearward-facing position until the infant's shoulders reach the lower shoulder seat used with from: height marker (approximately 12 months of age). internal harness • Convertible Booster Seat ( Note: you can until approximately...
  • Page 6 SPECIAL FEATURES: REARWARD-FACING SUITABLE FOR USE: REARWARD-FACING TO BE USED WITH A LAP SASH OR LAP ONLY SEAT BELT IN THE BACK OF MOST CARS WITH FORWARD-FACING SEATS. To be used only in a rearward-facing position until the 465mm child's shoulders reach the lower shoulder height marker (approximately 12 months of age).

  • Page 7: How To Setup

    SUITABLE FOR USE: REARWARD-FACING HOW TO SETUP INSTALLING INTO VEHICLE REARWARD Fully press Adjuster Button (A) while pulling Upper Anchorage FACING Strap (B) to lengthen. A. The restraint is normally packaged in the fully upright DO NOT USE RESTRAINT IN REARWARD FACING child use mode so if you need to use it for baby use you MODE WITHOUT STABILISING BAR FULLY EXTENDED.
  • Page 8 HOW TO SETUP HOW TO SETUP Infant Safety Cushion Insert INSTALLING INTO THE CAR D. Remove Infant Safety Cushion Insert, and gently lift headrest trim end, then pull backwards the centre panel flap, with the comfort pad from the inner seat of trim. A. Place the restraint rearward facing in the chosen seating position with the Messy Mat positioned centrally in the seating position.
  • Page 9 HOW TO SETUP HOW TO SETUP F. Engage seat belt buckle & tongue and tighten the H. Align restraint centrally to the chosen Rear facing seat belt allowing the sash to fully retract. Use the seating position. Pull sash portion of seat belt rear facing seat belt lock-offs to prevent the seat seat belt until all slack is removed from lock-off belt loosening.

  • Page 10: How To Install

    HOW TO SETUP HOW TO INSTALL Attachment Clip I. Fit the attachment clip to the car's anchor Attachment Clip fitting as shown. Make sure to remove as many twists as possible from the upper anchorage Car's Anchor Fitting strap. Refer to the car owner's handbook for Ensure Upper Anchorage Strap is tightened, the location of the child restraint anchor fitting.
  • Page 11 HOW TO INSTALL HOW TO INSTALL ANGULAR ADJUSTMENT OF RESTRAINT Important: If using an Extension Strap, positioning the Attachment Clip above the baby may lead to injury in an accident therefore make sure that the Attachment Clip is not positioned in front of the Some vehicle seats have more rearward slope than others.
  • Page 12 HOW TO INSTALL HOW TO INSTALL ADJUSTING HARNESS STRAP HEIGHT & HEADREST: 1. The shoulder straps must be in the slots which are nearest to the child's shoulders, but not lower than the child's shoulders. There is only one set of slots so the seat will always have the shoulder FOR BABY USE REARWARD-FACING straps in place.
  • Page 13 HOW TO INSTALL HOW TO USE ADJUSTING AHR TILT & ADJUST PLACING BABY INTO RESTRAINT Pull forward to HEADREST AND HARNESS STRAP A. Ensure the headrest and shoulder straps are adjusted to the unlock headrest HEIGHT correct height for your child (see page 6 and 7). A.
  • Page 14 - see previous page. while pulling both Shoulder Harness Straps to slacken Do not use restraint if straps do not tighten and contact Britax Childcare Customer Service. Refer to harness to the desired amount. back cover for details.
  • Page 15 HOW TO USE SPECIAL FEATURES: FORWARD-FACING TO REMOVE RESTRAINT FROM To be used only in a forward-facing position by children whose shoulder's have reached the lower Fully press Adjuster Button (A) shoulder height marker (approximately 12 months of age) until the shoulders reach the upper shoulder VEHICLE while pulling Upper Anchorage height marker (approximately 4 years of age.)
  • Page 16 SPECIAL FEATURES: FORWARD-FACING SUITABLE FOR USE - FORWARD-FACING 12. Car's Anchor Fitting 23 24 13. Vehicle seat belt TO BE USED WITH A LAP SASH OR LAP ONLY SEAT BELT IN THE BACK OF MOST CARS WITH 14. Pocket for Instruction Manual (Behind Restraint) FORWARD-FACING SEATS.
  • Page 17 HOW TO SETUP HOW TO SETUP INSTALLING INTO VEHICLE FORWARD FACING F. Convert the restraint to child use mode by placing one hand over rear corner of the base and lift the top (UPRIGHT OR RECLINED) end of restraint with the other hand until audible click A.
  • Page 18 HOW TO SETUP HOW TO SETUP H. Place one hand on the front corner of base J. Fully lengthen seat belt. Thread the seat belt into child use seat belt path (yellow marker) as shown Lift Grey Recline firmly, while with the other hand push the Grey below, ensuring that the seat belt is behind the harness straps and that the lap part of the seat belt is Latch Recline Latch up to unlock and push back until below the hook as shown below, on each side.
  • Page 19 HOW TO INSTALL HOW TO INSTALL INSTALLING INTO VEHICLE FORWARD-FACING Attachment (UPRIGHT OR RECLINED) Pull to remove Clip slack, then store M. Fit the attachment clip to the car's anchor fitting as Car's Anchor Fitting Attachment Clip the strap as shown shown. Make sure to remove as many twists as possible FORWARD-FACING Upper Anchorage from the upper anchorage strap.
  • Page 20 HOW TO INSTALL HOW TO INSTALL ADJUSTING HARNESS ADJUSTING AHR TILT & ADJUST STRAP HEIGHT AND HEADREST AND HARNESS STRAP Harness Shoulder slots. HEADREST: FOR CHILD USE HEIGHT Upper shoulder FORWARD-FACING (Height marker A. Loosen the harness straps before adjusting the hidden when headrest.
  • Page 21 HOW TO INSTALL HOW TO INSTALL PLACING CHILD IN THE RESTRAINT D. Ensure all slack is removed from Pull to remove harness lap straps by pulling shoulder slack from straps, then pull harness adjustment strap Shoulder Straps A. Lengthen harness by pushing and holding the harness lap to adjust harness to a comfortable but Pull to lengthen...
  • Page 22 HOW TO INSTALL CARE & MAINTENANCE TO RECLINE RESTRAINT REGULAR CARE OF THIS RESTRAINT: Lift Grey Recline Latch up while moving restraint into desired recline position. Please check the following items regularly to ensure the The child restraint may be reclined or positioned upright safety of your child: without removing the child from the restraint.
  • Page 23 A. Remove the restraint from vehicle. times. If the Harness Buckle cannot be returned to its original B. Disengage harness tongues from harness buckle. working condition then contact Britax Childcare Customer Peel away D. Remove any accessories such as the Infant Safety Cushion Insert.
  • Page 24 CARE & MAINTENANCE CARE & MAINTENANCE TO REPLACE COVER: (ii). To remove trim cover, unhook elastic trim body from behind Unhook elastic loops from the the restraint and at the front of the restraint underneath the A. Feed the Harness Tongues and shoulder straps through Lap strap slots. back of the restraint stabilising bar.
  • Page 25 ACCESSORIES ACCESSORIES IMPORTANT: CROTCH PAD Pocket ONLY USE SAFE-N-SOUND SEAT COVERS AND ACCESSORIES THAT ARE DESIGNED AND TESTED The Crotch Pad is designed to provide extra comfort for FOR USE WITH THIS PRODUCT. baby or child and is fitted to the restraint as follows: Feed Crotch Buckle through the slot in crotch pad as shown. Shoulder The following instructions apply to accessories that may be supplied with this restraint at point of Pads...
  • Page 26 TRAVELLING TIPS TRAVELLING TIPS SAFETY FEEDING Never hold a baby in arms when riding in a motor vehicle. In this position the baby could be thrown Never breast feed a baby while car is in motion. Babies will require extra feeding if travelling in the against the dashboard, windscreen or other occupant and suffer serious injury or death.
  • Page 27 PRE-INSTALLATION ANCHOR FITTING PRE-INSTALLATION ANCHOR FITTING Consult the vehicle owner’s handbook for location of anchorage fittings or anchorage points and the Extension Strap distance to be measured. possible use of spacers. Some vehicles may have an anchor fitting fitted by the vehicle manufacturer. Length 300mm (Use Safe-n-Sound part 0035). If anchorage points cannot be found refer to car manufacturer or local child restraint fitting station or Length 600mm (Use Safe-n-Sound part 0036). traffic authority for optimum position of anchorage point and the use of spacers. Available from all major child restraint retailers. UPPER ANCHORAGE STRAP DISTANCE TO MEASURE TO THE 45°...
  • Page 28 PRE-INSTALLATION ANCHOR FITTING PRE-INSTALLATION ANCHOR FITTING UPPER ANCHORAGE FITTING IF THE CAR IS FITTED WITH CHILD ONLY USE A 5/16 UNC GRADE 5 BOLT. IF THE BOLT IS NOT THE Note: Marking on Fig.1. CORRECT LENGTH THE CAR MANUFACTURER’S HAND BOOK RESTRAINT ANCHORAGE POINT Attachment Bolt the top of a Grade 5...

  • Page 29: In Case Of Accident

    Please assist the owner of this restraint in their claim. Harness • Improved canopy featuring sun visor for extended shade. NEW ZEALAND AUSTRALIA Britax Childcare (NZ) Ltd. • Rearward and forward facing seat belt Lock-offs provide a more Britax Childcare Pty. Ltd. secure fit in the vehicle. Customer Service 0508 688 822 A.B.N 55 006 773 600...
  • Page 30 Since its inception in 2006, the Crash Exchange program has helped 100’s of families ensure that their children have new restraints and that the restraints are not sold second hand placing others at risk. Our Crash Exchange Terms and Application form are accessible on our website. Please visit www.britax.com.au for further information.
  • Page 31 The Safe-n-Sound trademark and other trademarks are the property of Britax Childcare Pty. Ltd. (Australia). The Britax trademark is the property of Britax Excelsior Limited (UK). We reserve the right to alter this product without notice. © 1995-2010 Britax Childcare Pty. Ltd. This product is covered by Australian and overseas Patent applications.

Table of Contents