Jet JOVS-10 Operating Instructions And Parts Manual
Oscillating spindle sander
Hide thumbs
Also See for JOVS-10:
- Owner's manual (18 pages) ,
- Operating instructions manual (12 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Jet JOVS-10
Summary of Contents for Jet JOVS-10
- Page 1 Operating Instructions and Parts Manual Oscillating Spindle Sander Model JOVS-10 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708411 Ph.: 800-274-6848 Revision A 04/2010 www.waltermeier.com Copyright © 2010 Walter Meier (Manufacturing) Inc.
-
Page 2: Warranty And Service
Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with your local Walter Meier distributor, or visit waltermeier.com. WARRANTY JET products carry a limited warranty which varies in duration based upon the product (MW = Metalworking, WW = Woodworking). WHAT IS COVERED? This warranty covers any defects in workmanship or materials subject to the exceptions stated below. - Page 3 Replacing Sanding Sleeve ......................11 Dust Collection ..........................11 Maintenance ............................ 11 Replacement Parts ........................... 12 Breakdown for the JOVS-10 Oscillating Spindle Sander ..............13 Parts List for the JOVS-10 Oscillating Spindle Sander..............14 Sanding Assemblies ........................16 Sanding Assemblies ........................17...
-
Page 4: Warning
Warning Wear eye protection. Always keep guards in place and in proper operating condition. Do not operate the machine without the guards for any reason. This sander is intended to be used with wood and wood products only. Use of this sander and a dust collector with metal products is a potential fire hazard. - Page 5 • USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by JET may cause hazards or risk of injury to persons. • NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped. • CHECK DAMAGED PARTS. Before further use of the machine, a guard or other part that is...
-
Page 6: Grounding Instructions
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. -
Page 7: Specifications
Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for a JET Model JOVS-10 Oscillating Spindle Sander. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. -
Page 8: Contents Of The Shipping Container
It will make life easier in the woodshop. A JET Heavy Duty Universal Mobile Base is available to fit this sander. JET also has a variety of Dust Collectors and Air Filtration Units that will work nicely with your new sander. -
Page 9: Mounting Sanding Sleeves
Mounting Sanding Sleeves 1. Thoroughly clean the arbors (A, Figure 1) on all of the spindle assemblies. Also clean the arbor housing on the sander. 2. Slip the sanding sleeve (B, Figure 1) over the spindle and hold in place by tightening the set screw (C, Figure 1) with the supplied 2mm hex wrench. -
Page 10: Table Insert
Table Insert 1. Disconnect the sander from the power source, unplug. 2. Choose the insert (A, Figure 4) that most closely matches the diameter of the sanding drum. 3. Line up the notch in the insert with the spring pin in the table (B, Figure 4), and press in place. -
Page 11: Dust Collection
5. Tighten the set screw. Dust Collection In order to collect wood dust, attach a dust collection hose to the dust port. A variety of JET dust collectors, air filtration units, hoses and adaptors, etc. are available that will work effectively with your new sander. -
Page 12: Troubleshooting
Troubleshooting Trouble Probable Cause Remedy Sander unplugged from wall or motor. Check all plug connections. Fuse blown, or circuit breaker tripped Replace fuse, or reset circuit breaker. in service panel. Sander will not start. Cord damaged. Replace cord. Starting capacitor bad. Replace starting capacitor. -
Page 13: Breakdown For The Jovs-10 Oscillating Spindle Sander
Breakdown for the JOVS-10 Oscillating Spindle Sander... -
Page 14: Parts List For The Jovs-10 Oscillating Spindle Sander
Parts List for the JOVS-10 Oscillating Spindle Sander Index No. Part No. Description Size 7 ....OVS10-007 .....Power Cord ..................1 11 .... KEY5525....Key ....................1 18 .... OVS10-18 ....Oil Indicator ..................1 20 .... OS-30628....Oil Seal ....................1 21 .... BB-6206ZZ ....Ball Bearing............6206ZZ ...... 1 22 .... - Page 15 170 ..TS-0561031 ....Hex Nut............3/8”-16 ....... 2 171 ..JOVS10-171....Rubber Feet ..................4 172 ..JOVS10-172....Sinking Head Screw..........5/16”-18x3/4” ....4 174 ..JOVS10-174....JET Logo ................... 1 177 ..JOVS10-177....Pan Head Screw..........3/16”-24x3/8” ....2 178 ..JOVS10-178....Switch ....................1 179 ..JOVS10-179....Spring Pin ............3x22 ......1 180 ..
-
Page 16: Sanding Assemblies
Sanding Assemblies... -
Page 17: Sanding Assemblies
Sanding Assemblies Index No. Part No. Description Size 93....OVS10-093 ....Wrench ........................ 2 94....OVS10-094A ....Arbor ................3/4” ......... 6 95....OVS10-095 ....Hex Nut ....................... 6 96....OVS10-096 ....Spring Pin..............3.5x25 ......3 97....30105000J ....Spindle Assembly ............4” ........1 98....OVS10-098 .... -
Page 18: Electrical Connections
Electrical Connections... - Page 20 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.waltermeier.com...