Page 1 Toshiba Personal Computer TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual First edition December 2009 TOSHIBA CORPORATION File Number 960-784 [CONFIDENTIAL]...
Page 2 © 2009 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein.
Page 3 NOTE: “Note” contains general information that relates to your safe maintenance service. Improper repair of the computer may result in safety hazards. Toshiba requires service technicians and authorized dealers or service providers to ensure the following safety precautions are adhered to strictly.
Page 4 The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Qosmio F60 Series system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.
Page 5 Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations.
Page 6: Table Of Contents
Table of Contents Chapter 1 Hardware Overview Features ........................1-5 System Unit Block Diagram ..................1-13 3.5-inch Floppy Disk Drive (USB External) ............1-18 2.5-inch Hard Disk Drive..................1-19 Optical Drive (ODD) ....................1-22 Keyboard........................1-25 TFT Color Display....................1-26 Power Supply ......................
Page 7 Chapter 2 Troubleshooting Procedures Troubleshooting ......................2-6 Troubleshooting Flowchart..................2-8 Power Supply Troubleshooting................2-13 System Board Troubleshooting................2-22 USB FDD Troubleshooting ..................2-31 2.5” HDD Troubleshooting..................2-35 Keyboard Troubleshooting ..................2-40 Dual point Troubleshooting ..................2-41 Display Troubleshooting..................2-43 2.10 Optical Disk Drive Troubleshooting................
Page 8 Chapter 3 Tests and Diagnostics The Diagnostic Test ....................3-7 Executing the Diagnostic Test ................. 3-10 Setting of the hardware configuration ..............3-17 Heatrun Test......................3-19 Subtest Names......................3-20 System Test......................3-22 Memory Test......................3-22 Keyboard Test......................3-23 Display Test ......................3-24 3.10 Floppy Disk Test......................
Page 9 3.32 Maintenance (WinPE&FreeDos) Test Program Operation ........3-94 3.33 Starting TOSHIBA Test & Diagnostic ..............3-95 3.34 Windows PE T&D ....................3-97 3.35 DOS T&D ......................3-143 3.36 Maintenance (WinPE&FreeDos) Test Program Supplementary Information ..3-171 3.37 Maintenance (WinPE&FreeDos) Test Program Supplementary Information ..3-174...
Page 10: Chapter 1 Hardware Overview
1 Hardware Overview Chapter 1 Hardware Overview TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)[CONFIDENTIAL]...
Page 11 1 Hardware Overview TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 12 1 Hardware Overview Chapter 1 Contents Chapter 1 Hardware Overview..................1 Features ......................... 5 System Unit Block Diagram ..................13 3.5-inch Floppy Disk Drive (USB External) .............. 18 2.5-inch Hard Disk Drive.................... 19 Optical Drive (ODD) ....................22 1.5.1 DVD-ROM Drive.................. 22 1.5.2 DVD-Super Multi Drive................
Page 13 1 Hardware Overview Figures Figure 1-1 Front of the computer................... 10 Figure 1-2 System unit configuration ..................11 Figure 1-3 System unit block diagram................... 13 Figure 1-4 3.5-inch FDD (USB External)................18 Figure 1-5 2.5-inch HDD....................... 19 Figure 1-6 DVD Super Multi drive..................23 Figure 1- 7 Keyboard ......................
Page 14: Features
1 Hardware Overview Features The Toshiba TECRA A11/S11/P11/Satellite Pro S500 Series Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage and high reliability. This computer incorporates the following features.
Page 15 1 Hardware Overview  Chipset Toshiba TECRA A11/S11/P11/Satellite Pro S500 Series computer is Equipped with Intel Ibex peak QM57 or HM55.  VGA Controller The PC comes in with one of the following two types:  The internal graphics controller in Intel Ibex peak is used.
Page 16 1 Hardware Overview  TOSHIBA Dual Pointing Device The TOSHIBA Dual Pointing Device consists of Touch Pad and AccuPoint. The touch pad and control buttons enable control of the on-screen pointer and scrolling of windows. The pointer control stick and AccuPoint enables convenient control of the cursor.
Page 17 1 Hardware Overview  Bridge Media slot This slot lets you insert an SD™/SDHC™ memory card, miniSD™/microSD™ Card, Memory Stick® (PRO™/PRO Duo™), xD-Picture Card™ and MultiMediaCard  ExpressCard slot(Some models) This slot allows you to install a single ExpressCard device. ...
Page 18 1 Hardware Overview  Sound system The sound system is equipped with the following features:  Stereo speakers  Built-in microphone  Stereo headphone jack  External microphone jack  Internal modem The computer contains a MDC, enabling data and fax communication. It supports ITU-T V.90 (V.92).
Page 19: Figure 1-1 Front Of The Computer
Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.
Page 20: Figure 1-2 System Unit Configuration
1 Hardware Overview The system unit configuration is shown in figure 1-2 and 1-3 ） Figure 1-2 System unit configuration (case of 10, 10c model TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)[CONFIDENTIAL] 1-11...
Page 21 1 Hardware Overview Figure 1-3 System unit configurations (case of 10GC model) 1-12 TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 22: System Unit Block Diagram
1 Hardware Overview System Unit Block Diagram Figure 1-4 and 1-5 is a block diagram of the system unit. ） Figure 1-4 System unit block diagram (case of 10, 10c model TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)[CONFIDENTIAL] 1-13...
Page 23 1 Hardware Overview Figure 1-5 System unit block diagram (case of 10GC model) 1-14 TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 24 1 Hardware Overview The system unit is composed of the following major components:  Microprocessor The Toshiba TECRA A11/S11/P11/Satellite Pro S500 Series computer is equipped ® with an Intel Processor. The PC comes in with one of the following speeds: Intel®...
Page 25 1 Hardware Overview  Chipset Toshiba TECRA A11/S11/P11/Satellite Pro S500 Series computer is Equipped with Intel Ibex peak QM57 or HM55.  VGA Controller The PC comes in with one of the following two types:  The internal graphics controller in Intel Ibex pea is used.
Page 26  EC/KBC (Embedded Controller/Keyboard Controller)  One Mitsubishi M306KAFCLPR micon chip functions as both EC and KBC.  PSC (Power Supply Controller) One TOSHIBA TMP86FS49AUG chip is used. This controller controls the power sources.  Clock Generator L9LVRS394 is used.
Page 27: Inch Floppy Disk Drive (Usb External)
1 Hardware Overview 3.5-inch Floppy Disk Drive (USB External) The 3.5-inch FDD is a thin, high-performance reliable drive that supports 720KB (formatted) 2DD and 1.44MB (formatted) 2HD disks. The FDD is shown in figure 1-4. The specifications for the FDD are listed in Table 1-1. Figure 1-6 3.5-inch FDD (USB External) Table 1-1 3.5-inch FDD specifications TEAC FD-05PUB-337...
Page 28: Inch Hard Disk Drive
1 Hardware Overview 2.5-inch Hard Disk Drive The removable HDD is a random access non-volatile storage device. It has a non-removable 2.5-inch magnetic disk and mini-Winchester type magnetic heads. The computer supports a 160GB, 250GB or 320GB. The HDD is shown in figure 1-5. Specifications are listed in Table 1-2. Figure 1-7 2.5-inch HDD Table 1-2 2.5-inch HDD specifications Specifications...
Page 29 1 Hardware Overview Table 1-2 2.5-inch HDD specifications Specifications HGST HGST HGST HGST Items G8BC0006U32 G8BC0005Z160 G8BC0005Z250 G8BC0005Z320 Outline Width (mm) 100.2±0.25 Dimensio Height (mm) 9.5±0.2 Depth (mm) 69.85±0.25 Weight (g) 95 max 102 max 115 max Storage size (formatted) 160GB 250GB 320GB...
Page 30: Table 1-3 2.5-Inch Hdd Specifications
1 Hardware Overview Table 1-3 2.5-inch HDD specifications Specifications Items TSDC TSDC TSDC G8BC0006T160 G8BC0006T250 G8BC0006T320 Outline Width (mm) 100.0 Dimensio Height (mm) Depth (mm) 69.85 Weight (g) 97 typ 101 typ Storage size (formatted) 160GB 250GB 320GB Speed (RPM) 5,400 Internal transfer speed 464-1149 typ...
Page 31: Dvd-Rom Drive
1 Hardware Overview Optical Drive (ODD) 1.5.1 DVD-ROM Drive The DVD-ROM drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15-inch) DVD-ROM. The specifications of the DVD-ROM are described in Table 1-3. Table 1-4 DVD-ROM drive specifications Specifications Item TEAC DV-28S-WTA4 (G8CC0004QZ20) Outline Width (mm) 128 (excluding projections)
Page 32: Dvd-Super Multi Drive
1 Hardware Overview 1.5.2 DVD-Super Multi Drive The DVD Super Multi drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15-inch) CD- ROM, DVD-ROM, CD-R, CD-RW, DVD-R, DVD+R, DVD-RW, DVD+RW, DVD-RAM, DVD-R DL and DVD+R DL. The specifications are listed in Table 1-5. Figure 1-8 DVD Super Multi drive TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)[CONFIDENTIAL] 1-23...
Page 33: Table 1-5 Dvd Super Multi Drive Outline Dimensions
1 Hardware Overview Table 1-5 DVD Super Multi drive outline dimensions 項目仕様 Panasonic TEAC HLDS DV-W28S-VTA UJ890ADTJ6-A GT20N-ATAK7N1 G8CC0004LZ20 G8CC0004MZ20 G8CC0004RZ20 Outline Width (mm) 128 (excluding projections) dimensions Height 12.7 (excluding projections) (mm) Depth (mm) 129 (excluding projections) Mass (g) 172 or less 175±10 175±7...
Page 34: Keyboard
1 Hardware Overview Keyboard The keyboard is mounted 85(US)/87(UK) or 104(US)/105(UK)keys that consist of character key and control key, and in conformity with JIS. The keyboard is connected to membrane connector on the system board and controlled by the keyboard controller. Figure 1-7 is a view of the keyboard.
Page 35: Tft Color Display
1 Hardware Overview TFT Color Display The TFT color display consists of 15.6-inch HD /HD+ LCD module. 1.7.1 LCD Module The LCD module used for the TFT color display uses a backlight as the light source and can display a maximum of 16M colors with 1,366 x 768 or 1,600 x 900 resolutions. Figure 1-8 shows a view of the LCD module and Table 1-6 lists the specifications.
Page 36: Table 1-6 Lcd Module Specifications
1 Hardware Overview Table 1-6 LCD module specifications Specifications 15.6”HD(1366x768) Non-CSV Item Samsung LTN156AT10-501 LP156WH2-TLBB G33C0005T110 G33C0005M110 Number of Dots 1,366 (W) x 768 (H) Dot spacing (mm) 0.252(H)x0.252(V) Display range (mm) 359.3(H)x209.5(V)x5.5(D:Max) Specifications 15.6”HD(1366x768) CSV Item Samsung LTN156AT10-T01 LP156WH2-TLAB G33C0005S110 G33C0005L110 Number of Dots...
Page 37: Power Supply
1 Hardware Overview Power Supply The power supply supplies many different voltages to the system board and performs the following functions: 1. Judges that the DC power supply (AC adapter) is connected to the computer. 2. Detects DC output and circuit malfunctions. 3.
Page 38: Table 1-7 Power Supply Output Rating
1 Hardware Overview Table 1-7 Power supply output rating ACPI S4/S5 S4/S5 S4/S5 state M state Moff Moff Moff Moff Wakeup Powe Voltag Name Object r line e [V] name × × × × × × × Processor IGD-PGV × ×...
Page 39 1 Hardware Overview ○ ○ ○ ○ ○ ○ × EC/KBC M5V, ○ ○ ○ ○ ○ ○ × LED, ○ ○ ○ ○ ○ ○ ○ 1-30 TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 40: Batteries
1 Hardware Overview Batteries The computer has three types of batteries as follows:  Main battery pack  RTC battery The battery specifications are listed in Table 1-9. Table 1-8 Battery specifications Battery name Material Output Capacity voltage battery G71C000AF110 48Wh, 6 cell Main G71C000AG110...
Page 41: Battery Charging Control
1 Hardware Overview 1.9.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The microprocessor controls whether the charge is on or off and detects a full charge when the AC adaptor and battery are attached to the computer. The system charges the battery. Battery Charge When the AC adaptor is attached, there are two types of charge: When the system is powered off and when the system is powered on.
Page 42: Table 1-10 Data Preservation Time
1 Hardware Overview  Data preservation time When turning off the power in being charged fully, the preservation time is as following Table 1-11. Table 1-10 Data preservation time Condition preservation time Standby About 3 days Battery(48Wh, 6 cell) Shutdown About 40 days Battery(48Wh, 6 cell) Standby About 3 days 55Wh, 6 cell)
Page 43: Ac Adapter
1 Hardware Overview 1.10 AC Adapter The AC adapter is also used to charge the battery. Table 1-13 lists the AC adapter specifications. Table 1-12 AC adapter specifications Parameter Specification G71C000A5210 (2-pin) G71C000A6210 (3-pin) Power 75W (Peak 90W) Input voltage 100V/240V Input frequency 50Hz to 60Hz...
Page 44: Chapter 2 Troubleshooting Procedures
Troubleshooting Procedures Chapter 2 Troubleshooting Procedures TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 45 Troubleshooting Procedures 2-2 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 46 Troubleshooting Procedures Chapter 2 Contents Troubleshooting ..................... 2-6 Troubleshooting Flowchart ..................2-8 Power Supply Troubleshooting................2-13 2.3.1 Procedure 1 Power Status Check ............2-13 2.3.2 Procedure 2 Error Code Check ............2-15 2.3.3 Procedure 3 Connection Check............2-20 2.3.4 Procedure 4 Charging Check ............. 2-21 2.3.5 Procedure 5 Replacement Check ............
Page 47 Troubleshooting Procedures Display Troubleshooting..................2-43 2.10 Optical Disk Drive Troubleshooting..............2-45 2.10.1 Procedure 1 Diagnostic Test Program Execution Check ....2-45 2.10.2 Procedure 2 Connector Check and Replacement Check....2-45 2.11 Modem Troubleshooting..................2-47 2.11.1 Procedure 1 Diagnostic Test Program Execution Check ....2-47 2.11.2 Procedure 2 Connector Check and Replacement Check....
Page 48 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart (1/2) ................. 2-9 Figure 2-2 A set of tool for debug port testエラー! ブックマークが定義されていません。 Tables Table 2-1 Battery icon ......................2-13 Table 2-2 DC IN icon ......................2-14 Table 2-3 Error code......................2-16 Table 2-4 Debug port error status (1/2) pending ..............
Page 49: Troubleshooting
1. Phillips screwdrivers (For replacement procedures) 2. Implements for debugging port check  Toshiba MS-DOS system FD  RS-232C cross cable  Test board with debug port test cable  PC for displaying debug port test result...
Page 50 Troubleshooting Procedures There are following two types of connections in the figure of board and module connection in and after 2.3 Power Supply Troubleshooting. (1) Cable connection is described in the figure as line. (2) Pin connection is described in the figure as arrow. <e.g>...
Page 51: Troubleshooting Flowchart
Before going through the flowchart steps, verify the following:  Ask him or her to enter the password if a password is registered.  Verify with the customer that Toshiba Windows is installed on the hard disk. Non- Windows operating systems can cause the computer to malfunction.
Page 52 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (1/2) TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 53 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (2/2) 2-10 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 54 Troubleshooting Procedures If the diagnostics program cannot detect an error, the problem may be intermittent. The Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnostic test detected an error(s), then perform the appropriate troubleshooting procedures as follows: 1.
Page 55 Troubleshooting Procedures 15. If a malfunction is detected on the fingerprint sensor, perform the Fingerprint Sensor Troubleshooting Procedures in Section 2.18. 16. If a malfunction is detected on the Web camera, perform the Web camera Troubleshooting Procedures in Section 2.19. 2-12 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 56: Power Supply Troubleshooting
Troubleshooting Procedures Power Supply Troubleshooting The power supply controller controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. The procedures described in this section are: Procedure 1: Power Status Check Procedure 2: Error Code Check Procedure 3: Connection Check...
Page 57 Troubleshooting Procedures Table 2-2 DC IN icon DC IN icon Power supply status Lights blue DC power is being supplied from the AC adapter. Blinks orange Power supply malfunction Doesn’t light Any condition other than those above. *1 When the power supply controller detects a malfunction, the DC IN icon blinks orange.
Page 58: Procedure 2 Error Code Check
Troubleshooting Procedures 2.3.2 Procedure 2 Error Code Check If the power supply microprocessor detects a malfunction, the DC IN icon blinks orange. The blink pattern indicates an error as shown below.  Start Off for 2 seconds  Error code (8 bit) “1”...
Page 59 Troubleshooting Procedures Check 1 Convert the DC IN icon blink pattern into the hexadecimal error code and compare it to the tables below. Then go to Check 2. Table 2-3 Error code Error code Where error occurs DC Power (AC Adapter) Main battery 2nd battery S3V output...
Page 60: Main Battery
Troubleshooting Procedures  Main Battery Error code Meaning Main battery discharge current is over 0.5A. Main battery charge current is over 4.3A. The compensation value of [0A] is not within the limits from design data (± 400mA). Main battery charge current is over 0.3A when the charging is off. ...
Page 61 Troubleshooting Procedures  E3V output Error code Meaning E3V voltage is over 3.96V. E3V voltage is under 2.81V when the computer is powered on. E3V voltage is under 2.81V when the computer is booting up. E3V voltage is under 2.81V when EV power is maintained. ...
Page 62 Troubleshooting Procedures  1R05-E1V output Error code Meaning 1R05-E1V voltage is over 1.26V. 1R05-E1V voltage is under 0.89V when the computer is powered on. 1R05-E1V voltage is under 0.89V when the computer is booting up. 1R05-E1V voltage is under 1.26V when EV power is maintained. ...
Page 63: Procedure 3 Connection Check
Troubleshooting Procedures Check 2 In the case of error code 10h or 12h:  Make sure the AC adapter and AC power cord are firmly plugged into the DC IN 15 V socket and wall outlet. If the cables are connected firmly, go to the following step.
Page 64: Procedure 4 Charging Check
Troubleshooting Procedures 2.3.4 Procedure 4 Charging Check Check if the power supply controller charges the battery pack properly. Perform the following procedures: Check 1 Make sure the AC adapter is firmly plugged into the DC IN jack. Check 2 Make sure the battery pack is properly installed. If it is properly installed, go to Check 3.
Page 65: System Board Troubleshooting
Troubleshooting Procedures System Board Troubleshooting This section describes how to determine if the system board is malfunctioning or not. Start with Procedure 1 and continue with the other procedures as instructed. The procedures described in this section are: Procedure 1: Message Check Procedure 2: Debugging Port Check Procedure 3: Diagnostic Test Program Execution Check Procedure 4: Replacement Check...
Page 66: Procedure 1 Message Check
Troubleshooting Procedures 2.4.1 Procedure 1 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board and initializes it.  If an error message is shown on the display, perform Check 1. ...
Page 67 Troubleshooting Procedures If any other error message displays, perform Check 3. Check 3 The IRT checks the system board. When the IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) through (17), (23) or (24) is displayed, go to Procedure 4.
Page 68: Procedure 2 Debugging Port Check
Troubleshooting Procedures 2.4.2 Procedure 2 Debugging Port Check Check the D port status by a debug port test. The tool for debug port test is shown below. Serial Port model (W3270 short) Not a Serial Port model Figure 2-1 A set of tool for debug port test 1.
Page 69 Troubleshooting Procedures 4. Boot the computer in MS-DOS mode. 5. Execute GETDPORT.COM in the text menu in CPU REAL mode. (Insert the FD for starting D port into FDD and input “FD starting drive:>dport”.) The D port status is displayed in the following form; 6.
Page 70 Troubleshooting Procedures Table 2-4 Debug port error status (1/2) pending System BIOS Boot block processing Debug Code BIOS processing outline Target Device IC No. CPU setup IS1050 (CPU Socket) Initialization of IC3400 (Super I/O) Super I/O PCH ,Super I/O F000 Boot Block processing start BIOSROM IC3000 (BIOS ROM)
Page 71 Troubleshooting Procedures Table 2-4 Debug port error status (2/2) System BIOS IRT processing Debug Code BIOS processing outline Target Device IC No. F100 IRT section start IS1050 (CPU Socket) IC3000/IC3002 (BIOS ROM) Creation of SETUP BIOSROM F101 CN1400, CN1410 (RAM information Conn.) F102...
Page 72 Troubleshooting Procedures S3 shift start CN1400, CN1410 (RAM F116 Conn.) CN1400, CN1410 (RAM F117 S4 shift start Conn.) CN1400, CN1410 (RAM F118 S5 shift start Conn.) USB electric supply setting IC1600 (PCH) F119 start IC3200 (EC/KBC) Completion of a USB IC1600 (PCH) F11A electric supply setting...
Page 73: Procedure 3 Diagnostic Test Program Execution Check
Troubleshooting Procedures 2.4.3 Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the system board. Refer to Chapter 3, Tests and Diagnostic, for more information on how to perform these tests. 1.
Page 74: Usb Fdd Troubleshooting
Troubleshooting Procedures USB FDD Troubleshooting To check if the USB FDD is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: FDD Head Cleaning Check Procedure 2: Diagnostic Test Program Execution Check Procedure 3: Connector Check and Replacement Check 2.5.1 Procedure 1 FDD Head Cleaning Check FDD head cleaning is one option available in the Diagnostic Program.
Page 75: Procedure 2 Diagnostic Test Program Execution Check
Troubleshooting Procedures 2.5.2 Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test procedures. Make sure the floppy disk is formatted correctly and that the write protect tab is disabled.
Page 76: Procedure 3 Connector Check And Replacement Check
Troubleshooting Procedures 2.5.3 Procedure 3 Connector Check and Replacement Check USB FDD is connected to USB port on system board or USB/Sound board. The connection of the cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks.
Page 77 Troubleshooting Procedures Check 2 Connect USB FDD to other USB port and check if it works properly. If it does not work properly, perform Check 3 Check 3 USB FDD may be faulty. Replace it with a new one. If the problem still occurs, perform Check 4 Check 4 System board and USB / Sound board may be faulty.
Page 78: Hdd Troubleshooting
User’s Manual. 2.6.1 Procedure 1 Partition Check Insert the Toshiba DOS system disk and start the computer. Perform the following checks: Check 1 Input C: and press Enter. If you cannot change to drive C, go to Check 2. If you can change to drive C, go to Procedure 2.
Page 79: Procedure 2 Message Check
Troubleshooting Procedures 2.6.2 Procedure 2 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. When the test detects an error, an error message is displayed on the screen. Make sure no floppy disk is in the FDD.
Page 80: Procedure 3 Format Check
Troubleshooting Procedures 2.6.3 Procedure 3 Format Check The computer’s HDD is formatted using the DOS FORMAT program or the physical format program of the test program. To format the HDD, start with Check 1 below and perform the other steps as required. Refer to the DOS Manual for the operation of DOS.
Page 81: Procedure 4 Diagnostic Test Program Execution Check
Troubleshooting Procedures 2.6.4 Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnostics Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about the HDD test program.
Page 82: Procedure 5 Connector Check And Replacement Check
Troubleshooting Procedures 2.6.5 Procedure 5 Connector Check and Replacement Check The SATA HDD may be disconnected, or the SATA HDD or system board may be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure the SATA HDD is firmly connected to CN1900 on the system board.
Page 83: Keyboard Troubleshooting
Troubleshooting Procedures Keyboard Troubleshooting To check if the computer’s keyboard is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check 2.7.1 Procedure 1 Diagnostic Test Program Execution Check Execute the Keyboard Test (DIAGNOSTIC TEST) and Pressed key display test (ONLY ONE TEST) in the Diagnostic Program.
Page 84: Dual Point Troubleshooting
Troubleshooting Procedures Dual point Troubleshooting To check if the computer’s touch pad is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check 2.8.1 Procedure 1 Diagnostic Test Program Execution Check Execute the Touch pad test (ONLY ONE TEST) in the Diagnostic Program.
Page 85 Troubleshooting Procedures 2.8.2 Procedure 2 Connector Check and Replacement Check The connection of the cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the cables are firmly connected to the button board and system board.
Page 86: Display Troubleshooting
Troubleshooting Procedures Display Troubleshooting This section describes how to determine if the computer’s display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Cable Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program Execution Check...
Page 87 Troubleshooting Procedures Procedure 3 Replacement Check The LCD module and system board are connected to display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures. Check 1 Replace the LCD cable with a new one following the instructions in Chapter 4, Replacement Procedures and test the display again.
Page 88: Optical Disk Drive Troubleshooting
Troubleshooting Procedures 2.10 Optical Disk Drive Troubleshooting To check if optical disk drive is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check 2.10.1 Procedure 1 Diagnostic Test Program Execution Check Execute the CD-ROM/DVD-ROM Test in the Diagnostic Program.
Page 89 Troubleshooting Procedures Check 2 The SATA ODD may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. If the problem still exists, perform Check 3. Check 3 System board may be faulty. Replace it with new one following the instructions in Chapter 4, Replacement Procedure.
Page 90: Modem Troubleshooting
Troubleshooting Procedures 2.11 Modem Troubleshooting To check if modem is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check 2.11.1 Procedure 1 Diagnostic Test Program Execution Check Execute Modem test in the LAN/Modem/Bluetooth/IEEE1394 test program.
Page 91 Troubleshooting Procedures Check 2 Modem cable or MDC cable may be faulty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 MDC may be faulty. Replace it with a new one following the steps in Chapter 4, Replacement Procedure.
Page 92: Lan Troubleshooting
Troubleshooting Procedures 2.12 LAN Troubleshooting To check if the computer’s LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check 2.12.1 Procedure 1 Diagnostic Test Program Execution Check Execute LAN test in the LAN/Modem/Bluettoth/IEEE1394 test program.
Page 93: Wireless Lan Troubleshooting
Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting To check if the computer’s Wireless LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Transmitting-Receiving Check Procedure 2: Antennas’ Connection Check Procedure 3: Replacement Check 2.13.1 Procedure 1 Transmitting-Receiving Check Before starting the test, make sure the wireless communication switch is set in the ON position.
Page 94: Procedure 2 Antennas' Connection Check
Troubleshooting Procedures 2.13.2 Procedure 2 Antennas' Connection Check The wireless LAN function-wiring diagram is shown below: Any of the connections may be defective. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the wireless communication switch is “On”.
Page 95: Procedure 3 Replacement Check
Troubleshooting Procedures 2.13.3 Procedure 3 Replacement Check Wireless LAN card, wireless LAN antenna or system board may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Wireless LAN antenna may be faulty.
Page 96: Bluetooth Troubleshooting
Troubleshooting Procedures 2.14 Bluetooth Troubleshooting To check if the Bluetooth is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connection Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Make sure the wireless switch on the left side of the computer is turned “On”.
Page 97 Troubleshooting Procedures Check 2 The Bluetooth module may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures and check the operation. If the problem still exists, perform Check 3. Check 3 The Bluetooth cable may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures.
Page 98: Sound Troubleshooting
Troubleshooting Procedures 2.15 Sound Troubleshooting To check if the sound function is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check Procedure 3: Replacement Check 2.15.1 Procedure 1 Diagnostic Test Program Execution Check Execute the Sound test in Sound Test program disk.
Page 99: Procedure 3 Replacement Check
Troubleshooting Procedures 2.15.3 Procedure 3 Replacement Check  If headphone does not work properly, perform check 1.  If external microphone does not work properly, perform check 2.  If internal microphone does not work properly, perform check 3.  If Speaker Right does not work properly, perform check 5. ...
Page 100: Bridge Media Slot Troubleshooting
Troubleshooting Procedures 2.16 Bridge media Slot Troubleshooting This section describes how to determine if the computer's Bridge media functions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Check on Windows OS Procedure 2: Connector Check and Replacement Check 2.16.1 Procedure 1 Check on Windows OS Insert a Bridge media (SD memory card/SDIO card/Memory stick/Memory stick Pro/...
Page 101: Pci Expresscard Slot Troubleshooting
Troubleshooting Procedures 2.17 PCI ExpressCard Slot Troubleshooting This section describes how to check PCI ExpressCard slot by inspecting a card with PCI Express interface and a card with USB 2.0 interface. 1. Gigabit Ether ExpressCard 2. USB2.0 5in1 ExpressCard 1. Gigabit Ether ExpressCard (1) Insert the Gigabit Ether ExpressCard into the ExpressCard slot.
Page 102: Fingerprint Sensor Troubleshooting
Troubleshooting Procedures 2.18 Fingerprint sensor Troubleshooting CAUTION: To delete the account for confirming the fingerprint operation, it is necessary to log on by the account with the management authority. If the password has been set to log on, ask the Log-ON password to the user. To check if the Fingerprint sensor works correctly or not, follow the troubleshooting procedures below as instructed.
Page 103 Troubleshooting Procedures Procedure 1 Setting Windows Log-ON password 1. Open [User Account] from [Control Panel]. 2. Click [User Account]. 3. Click the icon of the account (user’s name) that you want to set the password. 4. Click “Create Account”. 5. Type a password in “Type a new password”. 6.
Page 104 Troubleshooting Procedures 7. When the Store to Sensor screen is displayed, check Store fingerprint to Sensor. Click Finish to complete fingerprint registration. Procedure 3 Authentication of fingerprint 1. Turn on the computer to start up Windows. 2. In the Windows logon window, put lightly the first joint of your finger registered and slide your finger sideways.
Page 105 Troubleshooting Procedures Procedure 4 Connector Check and Replacement Check The connection of the cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the cables are firmly connected to the Finger/pad board and system board.
Page 106: Web Camera Troubleshooting
Troubleshooting Procedures 2.19 Web camera Troubleshooting To check if the computer’s web camera is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Check on Windows OS Procedure 2: Connector Check and Replacement Check 2.19.1 Procedure 1 Check on Windows OS Use the software, Camera Assistant Software, which is originally prepared in the computer to check if the web camera can record/replay still images and moving images (including sound) without problems.
Page 107 Troubleshooting Procedures Check 2 If web camera does not work properly(the image from a web camera cannot be displayed. ), web camera may be faulty. Replace it with a new one following the steps in Chapter 4, Replacement Procedures. If the problem still occurs, perform Check 3 Check 3 System board may be faulty.
Page 108: Chapter 3 Tests And Diagnostics
Tests and Diagnostics Chapter 3 Tests and Diagnostics TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 109 Tests and Diagnostics 3-2 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 110 Tests and Diagnostics Chapter 3 Contents The Diagnostic Test ....................3-7 3.1.1 Diagnostics menu ................. 3-7 3.1.2 H/W (Hardware) initial information setting tool........3-8 3.1.3 Heatrun test program................3-9 Executing the Diagnostic Test ................. 3-10 3.2.1 Diagnostics menu (T&D) ..............3-13 3.2.2 H/W initial information setting tool ...........
Page 111 3.32.1 . Outline ....................3-94 3.32.2 Outline of Specification ..............3-94 3.33 . Starting TOSHIBA Test & Diagnostic ..............3-95 3.33.1 Starting from CD ................3-95 3.34 . Windows PE T&D ....................3-97 3-4 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 112 Tests and Diagnostics 3.34.1 Equipment Configuration for Test ............. 3-97 3.34.2 Starting T&D..................3-98 3.34.3 System Information Menu..............3-99 3.34.4 Test Menu..................3-103 3.34.5 System Utility Menu ................ 3-110 3.34.6 Details of Each Test Function ............3-116 3.35 DOS T&D ......................3-143 3.35.1 Configuration of Test Equipment.............
Page 113 Tests and Diagnostics Tables Table 3-1 Subtest names (1/2) .................... 3-20 Table 3-2 Error codes and error status names (1/3)............3-41 Table 3-3 Hard disk controller status register contents ............3-44 Table 3-4 HDC Error register contents................3-45 3-6 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 114: The Diagnostic Test
Tests and Diagnostics The Diagnostic Test This chapter explains how to use the Diagnostic Test programs to test the functions of the computer’s hardware modules. The Diagnostics Programs are stored on some Diagnostic Disks. There are Service Program Modules (DIAGNOSTIC MENU) and the Test Program Modules (DIAGNOSTIC TEST MENU) on the Diagnostic Disk.
Page 115: H/W (Hardware) Initial Information Setting Tool
 A cleaning kit to clean the floppy disk drive heads (Head Cleaning)  An external display supporting monitor ID (Expansion test)  A CD test media TOSHIBA CD-ROM TEST DISK or ABEX TEST CD-ROM (Sound test)  A DVD test media (DVD-ROM TEST DISK TSD-1) (Sound test) ...
Page 116: Heatrun Test Program
Tests and Diagnostics  The Diagnostics Disk (Main T&D) 3.1.3 Heatrun test program The heatrun test starts automatically after the selection. You will need the following equipment to perform this program.  The Diagnostics Disk (Main T&D) TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 117: Executing The Diagnostic Test
Tests and Diagnostics Executing the Diagnostic Test To start the Repair test program, follow these steps: 1. Insert the Repair test program disk in the USB floppy disk drive or Optical disk drive. 2. Turn on the computer while pressing U key. The following menu appears. The following menu is an example when Repair test program is performed from NOTE: the floppy disk.
Page 118 Tests and Diagnostics Step 3 The next message screen is displayed. * Re-push (NUMLOCK) key and any other key press key to continue. Check 1: According to a message, the [NumLock] key of a ten key is pressed and then the any other key is pressed.
Page 119 Tests and Diagnostics Step 6 The next message screen is displayed. * KB type Un mach KB..change KB configuration or retry (c: change KB configuration) (r: retry) Check 1: The KB configuration data saved at PC is rewritten. [c}key is pushed and [Enter] key is pushed.
Page 120: Diagnostics Menu (T&D)
Set the highlight bar to 3, and press Enter. The following DIAGNOSTIC TEST MENU will appear: TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTICS MENU : 1 - DIAGNOSTIC TEST 2 – ONLY ONE TEST...
Page 121 Set the highlight bar to 1, and press Enter. The following DIAGNOSTIC TEST MENU will appear: TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTIC TEST MENU : 1 - SYSTEM TEST 2 - MEMORY TEST...
Page 122 Tests and Diagnostics Select the option you want to execute and press Enter. When you select 1- SYSTEM TEST, the following message will appear: SYSTEM TEST NAME XXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST : XX PASS COUNT : XXXXX...
Page 123: H/W Initial Information Setting Tool
Tests and Diagnostics Use the up and down arrow keys to move the cursor to “ERROR STOP”. Use the right and left arrow keys to move the cursor to the desired option and press Enter. Selecting YES of ERROR STOP stops the test program when an error is found and displays the operation guide on the right side of the display screen as shown below: ERROR STATUS NAME [[ HALT OPERATION ]]...
Page 124: Setting Of The Hardware Configuration
Tests and Diagnostics Setting of the hardware configuration To execute this program, input 1 in the startup menu. Then press Enter to select the (2)- . The H/W initial information setting tool consists of four subtests. Initial config set Input the number you want to execute and press Enter. NOTE: Connect USB FDD, when you perform the Repair test program from the CD- ROM.
Page 125 Tests and Diagnostics 7. “Create DMIINFO TXT (Y/N)?” is displayed. Press Y, then the DMI information (text data) is written to the Floppy disk, etc. Setting of the HWSC Setting of the UUID Display of the DMI information (including UUID) After completion of the above settings, H/W configuration &...
Page 126: Heatrun Test
Tests and Diagnostics Heatrun Test To execute this program, press 2, Repair Heatrun and press Enter in the startup menu, press Enter. After selecting this test, the same subtests as 3.23 RUNNING TEST is executed successively. For more details on the procedure and test content, refer to RUNNING TEST. When the heatrun test ends, following message appears in the display.
Page 127: Subtest Names
Tests and Diagnostics Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/2) Test Name Subtest No. Subtest Name SYSTEM ROM checksum Fan ON/OFF Geyserville Quick charge DMI read Conventional memory MEMORY Protected Mode...
Page 128 Tests and Diagnostics Table 3-1 Subtest names (2/2) Test Name Subtest No. Subtest Name PRINTER Ripple pattern [Not supported] Function Wraparound FIR/SIR Point to point (send) ASYNC [Not supported] FIR/SIR Point to point (receive) Wraparound (board) HARD DISK Sequential read Address uniqueness Random address/data Cross talk &...
Page 129: System Test
Tests and Diagnostics System Test To execute the System Test select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 ROM checksum This subtest executes a checksum test of the BIOS ROM (range: F0000h to...
Page 130 Tests and Diagnostics If the CPU supports Gerserville (SpeedStep), this Subtest checks that the CPU operating clock speed can be changed. If the CPU does not support Gerserville (SpeedStep), the following message is displayed and the test is ended. This chip is not supported Subtest 04 Quick Charge This subtest checks the status for the quick charge.
Page 131: Memory Test
Tests and Diagnostics Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Conventional memory This subtest writes a constant data to conventional memory (0 to 640 KB),...
Page 132: Keyboard Test
Tests and Diagnostics Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Pressed key code display When a key is pressed, the scan code, character code, and key top name are...
Page 133: Display Test
Tests and Diagnostics Display Test To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 VRAM read/write for VGA This subtest writes the constant data (AAAAh and 5555h) to the video RAM.
Page 134 Tests and Diagnostics Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for following modes. To change the mode, press Enter. [Mode 12] [Mode 13] [Mode 3] [Mode 111 640*480 64K] [Mode 112 640*480 16M] [Mode 114 800*600 64K] [Mode 115 800*600 16M]...
Page 135 Tests and Diagnostics Subtest 06 “H” Pattern Display This subtest displays a full screen of “H” patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH To exit this subtest and return to the DISPLAY TEST menu, press Enter. NOTE: The last row may not be completely filled.
Page 136: Floppy Disk Test
Tests and Diagnostics 3.10 Floppy Disk Test CAUTION: Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD. The contents of the floppy disk will be erased. To execute the Floppy Disk Test, select 5 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen.
Page 137 Tests and Diagnostics Select the number of the subtest you want to execute and press Enter. The following message will appear during the floppy disk test. xxx DIAGNOSTIC TEST VX.XX FLOPPY DISK IN PROGRESS XXXXXXX [Ctrl]+[Break] : test end [Ctrl]+[C] key stop SUB-TEST : XX...
Page 138: Printer Test
Tests and Diagnostics 3.11 Printer Test CAUTION: Printer Test is not supported for this model. To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. NOTE: An IBM compatible printer must be connected to the system to execute this test. Also, printer port wraparound connector must be connected.
Page 139 Tests and Diagnostics Subtest 02 Function This subtest is for IBM compatible printers, and tests the following functions: Normal print Double-width print Compressed print Emphasized print Double-strike print All characters print This subtest prints the various print types shown below: Subtest 03 Wraparound NOTE: To execute this subtest, a printer wraparound connector must be connected to the...
Page 140: Async Test
Tests and Diagnostics 3.12 Async Test To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen.
Page 141: Hard Disk Test
Tests and Diagnostics 3.13 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter, and follow the directions on the screen. CAUTION: The contents of the hard disk will be erased when subtest 02, 03, 04, 06, 08 or 09 is executed.
Page 142 Tests and Diagnostics 4. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter. The following message will appear during each subtest. XXX DIAGNOSTIC TEST VX.XX HARD DISK TEST XXXXXXX [Ctrl]+[Break] :...
Page 143 Tests and Diagnostics Subtest 04 Cross talk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder, then reads the data while moving from cylinder to cylinder. (Test the data interference in the neighbor track) Worst pattern data Cylinder ‘B5ADAD’...
Page 144: Real Timer Test
Tests and Diagnostics 3.14 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Real time A new date and time can be input during this subtest.
Page 145 Tests and Diagnostics Subtest 03 Real time carry CAUTION: When this subtest is executed, the current date and time are erased. This subtest checks the real time clock increments, making sure the date and time are displayed in the following format: Current date : 12-31-1999 Current time : 23:59:58 The real time increments are automatically executed and the following is...
Page 146: Ndp Test
Tests and Diagnostics 3.15 NDP Test To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. CAUTION: Judge the existence of high-speed operation processor by 1bit of the composition byte. If exists, the bit is “1”. Test only when the high-speed operation processor exists.
Page 147: Expansion Test
Tests and Diagnostics 3.16 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 PCMCIA wraparound [It is not supported] CAUTION: PCMCIA wraparound test is not supported for this model. NOTE: To execute this subtest, the PC card wraparound connector is required.
Page 148 Tests and Diagnostics Subtest 02 RGB monitor ID NOTE: To execute this subtest, monitor supporting EDID (Extended Display Identification Data) is required. Connect a wraparound connector to CRT monitor for the test of ID acquisition. This subtest is executed by using VESA command. CAUTION: It becomes NG because the priority is given to the internal monitor in a simultaneous display mode.
Page 149: Cd-Rom/Dvd-Rom Test
To execute the CD-ROM/DVD-ROM test, select 12 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE: For the subtest 01, 02 and 03, use the TOSHIBA CD-ROM TEST DISK TDY-01 or ABEX TEST CD-ROM TCDR-702 and DVD-ROM TEST DISK TSD-1. For the subtest 04, use a CD-RW on the market.
Page 150: Error Code And Error Status Names
Tests and Diagnostics 3.18 Error Code and Error Status Names Table 3-2 lists the error codes and error status names for the Diagnostic Test. Table 3-2 Error codes and error status names (1/3) Device name Error code Error status name (Common) Data Compare Error ROM - CHECKSUM ERROR...
Page 151 Tests and Diagnostics Table 3-2 Error codes and error status names (2/3) Device name Error code Error status name FDD - BAD COMMAND ERROR FDD - ADDRESS MARK NOT FOUND FDD - WRITE PROTECTED FDD - RECORD NOT FOUND FDD - DMA OVERRUN ERROR FDD - DMA BOUNDARY ERROR FDD - CRC ERROR FDD - FDC ERROR...
Page 152 Tests and Diagnostics Table 3-2 Error codes and error status names (3/3) Device name Error code Error status name (HDD) HDD - WRITE FAULT HDD - STATUS ERROR HDD - BAD SECTOR HDD - ACCESS TIME ERROR HDD - NO HDD HDD - DMA CRC ERROR NDP - NO CO-PROCESSOR NDP - CONTROL WORD ERROR...
Page 153: Hard Disk Test Detail Status
Tests and Diagnostics 3.19 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on the screen by an eight-digit number.
Page 154 Tests and Diagnostics Table 3-4 HDC Error register contents Name Description “0” … Not used (Bad block mark) “1” … A bad block mark is detected. “0” … There is no uncorrectable data error. (Uncorrectable) “1” … Uncorrectable data error has been detected. ——...
Page 155: Only One Test
Tests and Diagnostics 3.20 ONLY ONE TEST 3.20.1 Program Description This program tests the unique functions of this model. 3.20.2 Operations Select test 2 from the DIAGNOSTIC MENU and press Enter. The following menu appears in the display. ################################################################ ######## ONLY ONE TEST Menu (QOSMIO G20) ######## ################################################################...
Page 156 Tests and Diagnostics Subtest 01 Pressed Key Display (Main key) When you execute this subtest, the keyboard layout is drawn on the display as shown below. When any key is pressed, the corresponding key on the screen changes to the key character that was pressed. Holding a key down enables the auto-repeat function that causes the key’s display character to blink.
Page 157 Tests and Diagnostics Subtest 02 Pressed Key Display (Ten key) When you execute this subtest, the keyboard layout is drawn on the display as shown below. When any key is pressed, the corresponding key on the screen changes to the key character that was pressed. Holding a key down enables the auto-repeat function that causes the key’s display character to blink.
Page 158 Tests and Diagnostics Subtest 03 Touch Pad This subtest checks the functions of the touch pad as shown below. A) Direction and parameter B) Switching function check. This test displays the response from the touch pad and touch pad switch. When moving your finger on the touch pad towards the upper left, the <POINTING>...
Page 159 Tests and Diagnostics Subtest 04 Wireless communication Switch This subtest checks if the Wireless communication switch works properly. If the test is started with the switch ON, following message appears in the display. Wireless communication Switch is set to a start position (OFF) Slide the switch to OFF position.
Page 160 Tests and Diagnostics NG message appears in the display if a defective is found during the test. Confirm the connection of cable, then execute the test again. Press 9 and return to ONLY ONE TESST menu. Subtest 06 This subtest checks if each LED lights properly. The following message appears in the display in order.
Page 161 Tests and Diagnostics Subtest 07 Button This subtest checks the moving of the of the front operation panel button. Press the eco button after the following message appears. Step 1 Press Function button (Assist button ) OK message appears in the display if the test ends without an error. Press any key return to each Steps if NG! or Press any key message apprears.
Page 162 Tests and Diagnostics Subtest 08 Acceleration sensor This subtest detects and corrects the each axis (X, Y, Z). NOTE: Make sure that this subtest is executed on the following condition: 1. Flat desk with vertical plane to get the stability of machine. 2.
Page 163 Tests and Diagnostics When this subtest is selected, the following message appears in the display. The heaven surface establishes in the upper direction Press [Enter] key NOTE: Be sure to execute the test with the display panel opened. Set the machine on the flat desk. Then press Enter to detect the data on this setting of machine.
Page 164 Tests and Diagnostics Subtest 09 Docker Dock/Undock This subtest is executed with an Slim Port Replicator II. installed. Press Enter while pushing the eject button of the Slim Port Replicator II. the following message appears. Pushing Eject-SW, and press [Enter] Key Press Enter without pushing the eject button of the Slim Port Replicator II.
Page 165 Tests and Diagnostics Subtest 0B Volume This subtest checks if control dial works properly. Volume Step1 The following message appears in the display. Volume button test Press Volume [ Down(-) ] Please press volume down button. Step2 The following message appears in the display. Volume button test Press Volume [ Up(+) ]...
Page 166: Head Cleaning
Tests and Diagnostics 3.21 Head Cleaning 3.21.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.21.2 Operations 1. Selecting test 4 from the DIAGNOSTIC MENU and pressing Enter displays the following messages: DIAGNOSTICS - FLOPPY DISK HEAD CLEANING : VX.XX Mount cleaning disk(s) on drive(s).
Page 167: Log Utilities
Tests and Diagnostics 3.22 Log Utilities 3.22.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk or output the data to a printer. Connect USB FDD, when you perform the DIAGNOSTIC PROGRAM from the NOTE: DVD-ROM.
Page 168: Operations
Tests and Diagnostics 3.22.2 Operations Select 5 and press Enter in the DIAGNOSTIC MENU, logs error information into RAM or onto a floppy disk. The error information is displayed in the following format: XXXXX ERRORS TS-NO PASS STS ADDR WD RD HSTS [ERROR STATUS NAME] FDD 02 0000 103 00001 00 00 0000 FDD-WRITE PROTECTED...
Page 169: Running Test
Tests and Diagnostics 3.23 Running Test 3.23.1 Function Description This function automatically executes the following tests in sequence: 1. System test (subtest 01) 2. Memory test (subtests 01, 02) 3. Display test (subtest 01) 4. Real timer test (subtest 02) 5.
Page 170: Floppy Disk Drive Utilities
1. FORMAT NOTE: This program is only for testing a floppy disk drive. The option is different from the Toshiba MS-DOS FORMAT command. This program can format a floppy disk in the following formats: (a) 2DD: Double-sided, double-density, double-track, 96/135 TPI, MFM mode, 512 bytes, 9 sectors/track.
Page 171: Operations
Tests and Diagnostics 3.24.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message: [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 – HDD-ID READ 9 - EXIT TO DIAGNOSTICS MENU 2.
Page 172 Tests and Diagnostics 3. COPY program (a) When COPY is selected, the following message appears: FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will display a message similar to the one below: Insert source disk into drive A: Press any key when ready.
Page 173 Tests and Diagnostics 4. DUMP program (a) When DUMP is selected, the following message appears: DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) Select a drive type. If is selected, the display will go to step (h). If 2:HDD is selected, the following message will appear: 1:FDD...
Page 174 Tests and Diagnostics (k) The following message will appear. To finish the dump, select 3. Press number key (1:up,2:down,3:end) ? (l) The following message will appear. Selecting 2 returns to the FDD UTILITIES MENU. Another dump (1:Yes,2:No) ? HDD ID READ program Selecting HDD ID displays the following HDD ID configuration: [HDD ID Read (VX.XX)] [Drive #1] [Drive #2]...
Page 175: System Configuration
Tests and Diagnostics 3.25 System Configuration 3.25.1 Function Description The System Configuration program contains the following configuration information for the computer: 1. Processor Type [Code/L2 cache] 2. Chip set [VRAM] 3. BIOS ROM version [1st ID, 2nd ID] 4. Boot ROM version 5.
Page 176: Operations
Tests and Diagnostics 3.25.2 Operations Select 8 from the DIAGNOSTIC MENU and press Enter. Then, the following system configuration appears in the display. System Configuration Display: Ver X.XX [Machine Name???] - Processor Type = XXXXXX-XXXXXMHz Code = XX L2 Cache = XXXXXKB - Chip set = XXXXXX VGA Chip =...
Page 177: Wireless Lan Test Program (Atheros)
1. Slide the wireless communication switch to “ON” position. 2. Check the card type according to the following procedure: Click [Start] -> [All Programs] -> [TOSHIBA] -> [Utilities] -> [PC Diagnostic Tool]. Check the “Network”. If the “ ” , “...
Page 178 Tests and Diagnostics Check of the antenna connection 1. Confirm that the icon for wireless LAN appears at the lower right of the screen under the circumstances the wireless LAN communication is available. (It is no problem if a cross is shown on the icon.) 2.
Page 179: Wireless Lan Test Program (Intel-Made A/B/G/N Setting Up Of Ref Pc)
Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel-made a/b/g/n Setting up of REF PC) For the test of Intel-made wireless LAN cards, configure the test environment as shown below with the following equipment. ・ AP （which can operate on Windows XP and is corresponding to access point 11a, 11b and 11g）...
Page 180 Tests and Diagnostics Open “My Computer” window and click “My Network places” on the left column. Click “View network connections” on the left column. The “Network Connections” window appears. Double-click “Local Area Connection”. Network Connections window TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 3-71...
Page 181 Tests and Diagnostics Click “Install…” button on the “Local Area Connection Properties” window. Local Area Connection Properties window Select “Protocol” on the “Select Network Component Type” window and click “Add…” button. Select Network Component Type window Click “Have Disk…” button on the “Select Network Protocol” window. Select Network Protocol window 3-72 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 182 Tests and Diagnostics When “Install From Disk” window appears, click “Browse…” and specify the created “Clx_Res” folder. Then Click “OK”. (For the test, “PACKET.INF” file is used.) Install From Disk window The “Select Network Protocol” window appears again. In the “Network Protocol”, “DDK PACKET Protocol”...
Page 183 Tests and Diagnostics After the completion of REF PC setup, restart the WINDOWS. Then perform the Responder test program for Windows (WTWINSVR.EXE) in the Clx_Res folder. ・WTWINSVR.EXE Function : Transmitting/receiving of data to/from DUT via AP OS available : Windows XP only How to start : Double-click WTWINSVR icon.
Page 184: Wireless Lan Test Program On Dut Pc (Intel-Made)
Tests and Diagnostics 3.28 Wireless LAN Test Program on DUT PC (Intel-made) 3.28.1 Wireless LAN Test Program (Intel-made : Shirley Peak) on DUT PC This section describes how to perform the wireless LAN transmitting-receiving test (Intel- made 802.11 a/b/g). To execute the wireless LAN test, use the Diagnostics disk for wireless LAN test.
Page 185 Tests and Diagnostics To execute the subtest, input the subtest number and press Enter. Subtest01 Communication test of 11a mode for 5100/5150 module (Two antenna type) This subtest execute transmitting/receiving test in 802.11a mode using the main antenna. If a defective is not found during the test, OK message will appear in the display.
Page 186 Tests and Diagnostics Subtest03 Communication test of 11g mode for 5100/5150 module (Two antenna type) This subtest execute transmitting/receiving test in 802.11g mode using the main antenna. If a defective is not found during the test, OK message will appear in the display.
Page 187 Tests and Diagnostics Subtest06 Communication test of 11b mode for 5100/5150 module (Three antenna type) This subtest execute transmitting/receiving test in 802.11b mode using the main antenna. If a defective is not found during the test, OK message will appear in the display.
Page 188: Lan/Modem/Bluetooth/Ieee1394 Test Program
Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program This section describes how to perform the LAN/Modem/Bluetooth/IEEE1394 test with the test program. Insert the test program disk for LAN/Modem/Bluetooth/IEEE1394 test in FDD and turn on the power. The following message will appear: Microsoft Windows XX Startup Menu ---------------------------------- Modem...
Page 189 Tests and Diagnostics Subtest01 (i82562 + ICHx) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. The following message will appear: [LAN transmit & receive test !] COMPLETED Repeat count = 00000 Error count 00000 LOOPBACK TEST 100Mbps Auto-negotiation TxRx Test...
Page 190 Tests and Diagnostics Subtest02 (GbE) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. Select 2 to execute and press Enter. The following message will appear: Testing adaptor...hit <ESC> to abort. External Loopback Test...PASSED Testing completed.
Page 191: Modem Test
Tests and Diagnostics 3.29.2 Modem test For this subtest, connect the modem PCB and RJ11 connector with a harness. Use the dedicated “FAT-MODE inspection device (product code: QE2000P01 made by Nitto Denki Seisakusyo)” for the tests. ################################################################## ###### AC97' Modem Controller Diagnostics program ####### ################################################################## 1 ....
Page 192: Bluetooth Test
(A mobile phone with the Bluetooth function is also available.) ・ A Bluetooth card should be installed on the target computer. Install the Bluetooth function by clicking [All Programs] -> [TOSHIBA] -> [Bluetooth] -> [Bluetooth Settings]. Test procedure 1.
Page 193 Tests and Diagnostics 5. Select “Diagnostics” tab and click “Run”. 6. Check the “Log” to confirm the test result. BT address of test computer BT address of responder device 7. When the BT (Bluetooth) address of the responder device appears, the Bluetooth card and antenna connection are OK.
Page 194: Ieee1394 Test (Not Used)
Tests and Diagnostics 3.29.4 IEEE1394 test (Not Used) To execute this test, input 4 and press Enter. NOTE: Use another computer that can communicate by IEEE1394 (i. Link) cable as a reference machine to perform this test. The following menu will appear: ******************************************************************** ******** IEEE1394[XXXXX] Diagnostics program...
Page 195: Sound Test Program
Therefore, please test the sound on Windows OS. 1) Play a music file. 2) click TOSHIBA-> utility -> "PC diagnostic tool." to test the sound Please check operation of speakers by one of methods. 3-86 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 196: Setup
Tests and Diagnostics 3.31 SETUP 3.31.1 Function Description This program displays the current system setup information as listed below: Main menu 1. System Time（System time ） 2. System Date（System date ） 3. CPU Type 4. CPU Speed 5. HDD1/SSD1 6. ODD 7.
Page 197: Power Management Menu
Tests and Diagnostics Power Management menu 18. Wake-up on LAN 19. Wake-up on LAN on Battery 20. Wake on Keyboard 21. Critical Battery Wake-up 22. Dynamic CPU Frequency Mode 23. Core Multi-Processing 24. Intel Turbo boosts 25. eSATA 26. SATA Interface setting 27.
Page 198: Accessing The Setup Program
Tests and Diagnostics 3.31.2 Accessing the SETUP Program Turn on the power SW. then press F2. The following display appears. Main menu screen TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 3-89...
Page 199 Tests and Diagnostics Security menu screen Power Management menu screen 3-90 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 200: Exit Menu Screen
Tests and Diagnostics Advanced menu screen Exit menu screen TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 3-91...
Page 201 Tests and Diagnostics Moving Within the SETUP Menu and Changing Values 1. Press  and  to move between the two columns. Press  and  to move between items in a column. 2. Press either the [Enter]Key to change the value. Accepting Changes and Exiting the SETUP Window 1.
Page 202 Tests and Diagnostics How to change setup Options Since a help is displayed on the right-hand side of each menu screen, it is referred to. TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 3-93...
Page 203: Maintenance (Winpe&Freedos) Test Program Operation
Tests and Diagnostics 3.32 Maintenance (WinPE&FreeDos) Test Program Operation 3.32.1 . Outline This document explains how to operate T&D that is released through TOSHIBA Test & Diagnostic CD. 3.32.2 Outline of Specification The TOSHIBA Test & Diagnostic CD already released includes WindowsPE T&D (hereafter, referred as WinPE T&D) and Freedos T&D (hereafter, referred as Fdos T&D) and...
Page 204: Starting Toshiba Test & Diagnostic
3.33 . Starting TOSHIBA Test & Diagnostic 3.33.1 Starting from CD 1. Load the TOSHIBA Test & Diagnostic Discs into the optical disc drive and turn off the computer's power. 2. While holding down F12 key on the keyboard, turn on your computer - when the logo screen appears, release the F12 key.
Page 205 Tests and Diagnostics NOTE: After [winpe] is selected, the following message is displayed on the screen. At this time, ”Press any key to boot from CD or DVD..” is displayed, but only [ENTER] key is valid. ress the Enter key again on this screen. If the Enter key is pressed, WindowsPE will start. The key different from an Enter key is pressed.
Page 206: Windows Pe T&D
Tests and Diagnostics 3.34 . Windows PE T&D 3.34.1 Equipment Configuration for Test The following table indicates equipment configuration necessary for conduction of the tests items shown below using WinPE T&D. Test Item Equipment required Remarks USB flash memory Free space : More than 12MB (When you start WinPE T&D from a USB memory, use 512MB or more of USB memory.) Media containing test data...
Page 207: Starting T&D
After the startup of the OS, unless CD volume name is WINTDCD or USB volume name is WINTDUSB, WinPE T&D does not start automatically. Note: If the system starts up from the TOSHIBA Test & Diagnostic CD, WinPE T&D in the USB memory starts when the USB memory created in section 3-5-2 is connected.
Page 208: System Information Menu
Tests and Diagnostics 3.34.3 System Information Menu If you set the TOSHIBA Test & Diagnostic CD to the ODD drive and run WinPE T&D, the following test selection screen is displayed. (For further details, refer to Chapter 2.) Hereinafter, System Information will be described in detail.
Page 209 Tests and Diagnostics 3.34.3.2 Details of the system information displayed on an information tree The details of the system information item displayed on each information tree are shown below. ● BIOS The following items display DMI and BIOS information of the PC. Item Description Manufacturer...
Page 210 Tests and Diagnostics ● MEMORY The following item displays memory information of the PC. Item Description Physical Memory Displays the capacity (GB) of the physical memory on the PC ● NETWORK The following items displays network card information of the PC. If more than one network card is connected, the information of up to 4 network cards are displayed.
Page 211 Tests and Diagnostics ● ODD The following item displays ODD information of the PC. If more than one ODD is connected, the information of up to 4 ODDs are displayed. Item Description ODD0 - 3 Displays the name and the media type of the ODD connected to the PC.
Page 212: Test Menu
Tests and Diagnostics 3.34.4 Test Menu This section explains the Diagnostics screen. 3.34.4.1 Explanation of each item ▼ [Multitask] check box Checking this box activates each test as multi-task. ▼ [CPU Stress] check box Checking this box applies any stress to the CPU during the test. Restriction: If the test is conducted, uncheck Multitask in the Simple mode before the test because of too much stress to be applied to the CPU.
Page 213 Tests and Diagnostics ▼ Testing time Updates the testing time and displays it in real time during the execution of the test. ▼ Test setting and Result This will be explained in section 3-4-2. 3.34.4.2 Test setting and Result ▼ TEST Item Checks the check box of the item to be tested. ▼...
Page 214 Tests and Diagnostics Status Description Device not connected Peripheral device necessary for the test is not connected. USB flash memory, FDD and others may be connected to the PC. Device has a problem Failure occurred in the device driver. This Device is disabled The device has been removed.
Page 215 Tests and Diagnostics 3.34.4.3 Test Procedure This section describes operation procedure of WinPE T&D. 1) Select the test item to run from Test Item and check it. (If you put a check mark in the ALL Item Check check box, all test items are checked.) 2) Select the test mode of each test.
Page 216 Tests and Diagnostics 3.34.4.4 Display of Test Result If the test ends successfully or the [STOP] button is clicked, the following Result screen is displayed. After confirming the result, click the [CLOSE] button to close the screen. After the display of the test result screen, the test result logs are saved to X drive. Note: WinPE is extracted on the RAM disk on drive X.
Page 217 Tests and Diagnostics 2) How to save log files The following is the procedure to save log files to an external media Test logs in the text format and HTML log files are saved to the external media. 2-1) Click the check box of the log file to save. If you click the [ALL Select] button, all the check boxes of the log files are checked.
Page 218 Tests and Diagnostics 2-3) If a destination confirmation message is displayed, click the [OK] button. 2-4) If the log file is successfully saved to the destination, the following confirmation screen is displayed and click the [OK] button. 2-5) After saving the log files, click the [Close] button to close the Management screen. TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 3-109...
Page 219: System Utility Menu
Tests and Diagnostics 3.34.5 System Utility Menu This section explains System Utility screen. 3.34.5.1 Explanation of Each Item ▼ Utility Item … A list of the utilities that this T&D supports ▼ Detail … Explanation of each utility is described. If you point to the utility which you wish to execute and click it, the utility starts.
Page 220 Tests and Diagnostics 3.34.5.2 USB Memory Creation Tool If the system is booted using the USB memory created in 3-5-2, the following screen is displayed. Press the arrow keys to operate on the multi-boot screen. Move the cursor to the desired item and press the Enter key. [WindowsPE T&D]: Starts up WindowsPE and then starts WinPE T&D.
Page 221 Tests and Diagnostics This utility extracts the contents of TOSHIBA Test & Diagnostic to the specified USB memory to provide the environment which allows you to start the test from the USB memory and conduct it. If the utility is executed, the following screen is displayed.
Page 222 Tests and Diagnostics 3.34.5.3 Display of SMART Information This utility lists the SMART information on the screen. Attribute and Worst values for each ID are also displayed. Since some HDDs do not have ID, these information are not displayed in that case. The following screen displays the SMART information of the first HDD.
Page 223 Tests and Diagnostics Each ID and its details are listed in the following table. Attribute Name Description Raw read error rate Read error rate Rate of errors which occur when the HDD reades data. Throughput performance Throuput performance Spin up time Start-up time of spindle mortor Averate time from turning the power on to starting spinning...
Page 224 Tests and Diagnostics UltraDMA CRC error count Number of CRC errors occurred during data transference in the UltraDMA mode DFh Load/Unload retry count Number of reloads of more than a certain amount of times TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 3-115...
Page 225: Details Of Each Test Function
Tests and Diagnostics 3.34.6 Details of Each Test Function 3.34.6.1 HDD Physical Test 1) Test content This test handles the HDDs to the PC as physical unit and conducts read test to the target HDD to check whether it works or not. Up to first four HDDs connected to the PC can be the target of the test.
Page 226 Tests and Diagnostics ■ In the case of FAIL The Error Count on the test screen is zoomed in and (NG) is displayed in the Result field on the WinPE T&D screen. The detail of the error is printed to the log of WinPE T&D. Move details are as shown below. Message Explanation Remarks...
Page 227 Tests and Diagnostics 3.34.6.2 HDD Logical Test 1) Test content This test first verifies that the files which exist on the drive recognized as the built-in HDD are read normally. During the verification operation, the status update is performed sequentially (display of file names in File Name) and when the verification reaches the last file, it is terminated.
Page 228 Tests and Diagnostics 3.34.6.3 Memory Test 1) Test content This test reserves free memory area in the main memory and performs Write, Read and Compare operation to the area to verify data validity. A test using burst transfer is also performed.
Page 229 Tests and Diagnostics 3) Result judgment ■In the case of PASS The PASS Count on the test screen is zoomed in and (OK) is displayed in the Result field on the WinPE T&D screen. ■In the case of FAIL The PASS Count on the test screen is zoomed in and (NG) is displayed in the Result field on the WinPE T&D screen.
Page 230 Tests and Diagnostics 3.34.6.4 USB Test 1) Test content This test accesses a file on the disk in the USB device (USB Flash Memory) to verify the file validity. Create a file with the specified size in the USB device and delete the file after creating it. ■...
Page 231 Tests and Diagnostics 3) Result judgment This test is regarded as 1PASS when every access to the files in all of the devices connected to the PC is successful. If an error occurs even in a device, the error count is incremented. ■...
Page 232 Tests and Diagnostics 3.34.6.5 ODD Test 1) Test content This test reads the test data in the CD inserted on the CD drive (External CD driver is also possible) to verify the data integrity. During the verification operation, update of the read address is performed (displayed on the right side of the Addressing Data) and when the verification reaches the end of the data, it is terminated.
Page 233 Tests and Diagnostics ■ In the case of PASS The PASS Count on the test screen is zoomed in and (OK) is displayed in the Result field on the WinPE T&D screen. ■ In the case of FAIL The Error Count on the test screen is zoomed in and (NG) is displayed in the Result field on the WinPE T&D screen.
Page 234 Tests and Diagnostics 3.34.6.6 WIRED LAN Test 1) Test content This test checks that normal communication can be performed with the built-in LAN card. To execute the test, it is necessary that Mac address for the LAN card should have been set and IP address should have been given to the machine.
Page 235 Tests and Diagnostics ■ In the case of FAIL The Error Count on the test screen is zoomed in and (NG) is displayed in the Result field on the WinPE T&D screen. The detail of the error is printed to the log of WinPE T&D. More details are as shown below. Message Explanation Remarks...
Page 236 Tests and Diagnostics 3.34.6.7 CPU Test 1) Test content This test performs arithmetic operation test to the CPU to verify the CPU operation. The test processes ALU and FPU operations and allows you to check that the results are correct. ■Simple Mode / Detail Mode Conduct the same test in both Simple mode and Detail mode.
Page 237 Tests and Diagnostics The detail of the error is printed to the log of WinPE T&D. More details are as shown below. Message Explanation Remarks The ALU test made an An error occurred error. duringprocessing of ALU. The FPU test made an An error occurred error.
Page 238 Tests and Diagnostics 3.34.6.8 VIDEO Test 1) Test content This test displays red, green, blue, white and black colors, circles, line gradation, ASCII characters and H pattern full screen. ■ Simple Mode This test mode displays red, green, blue, white and black colors, circles, line gradation, ASCII characters and H pattern full screen.■Detail Mode This test mode performs display of test items in the Simple mode as well as random drawing of circles, squares and lines.
Page 239 Tests and Diagnostics 3.34.6.9 FDD Test 1) Test content This test accesses a file on a floppy disk and verifies that the access can be made correctly. Create a file with the specified size on a floppy disk and delete the file after creating it Perform the test after inserting a floppy disk to the drive.
Page 240 Tests and Diagnostics Message Explanation Remarks Space Size Error. There is no sufficient free space This message also appears Code(xx) for the file with the specified size. when no floppy disk is in the xx indicates error code. floppy disk drive. Open File Error.
Page 241 Tests and Diagnostics 3.34.6.10 IEEE1394 Test 1) Test content This test accesses a file in the IEEE1394 device and verifies that the access can be made correctly. Create a file with the specified size in the IEEE1394 device and delete the file after creating ■...
Page 242 Tests and Diagnostics the WinPE T&D screen. The detail of the error is printed to the log of WinPE T&D. More details are as shown below. Message Explanation Remarks File Access Failed the file access Error.xx: xx indicates drive name. Space size There is no sufficient free space Error.Code(xx:)
Page 243 Tests and Diagnostics 3.34.6.11 TIMER Test 1) Test content Execute the test after adjusting the internal time and verify the accuracy of the timer after it passes the year 2000. ■ Simple Mode / Detail Mode Simple Mode tests at intervals of order 5 seconds. Detail Mode tests at intervals of order 10 seconds.
Page 244 Tests and Diagnostics 3) Result judgment Both of PASS and FAIL are not displayed anywhere on the TIMER screen. The result is reflected to the log on the WinPE T&D screen. ■ In the case of PASS The PASS Count display on the test screen is zoomed in and (OK) is displayed in the Result field on the WinPE T&D screen.
Page 245 Tests and Diagnostics 3.34.6.12 KEYBOARD Test 1) Test content The keyboard of PC is a test which judges whether it operates normally. ■Simple Mode / Detail Mode The same operation is carried out whichever it chooses. 2) Test screen The arrangement of a keyboard is displayed on the display of PC. 3-136 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 246 Tests and Diagnostics 1) If the press of a key is recognized correctly, the object key on a display will be eliminated. 2) When redoing a keyboard test, the "Refresh" button arranged at the screen lower left is pressed. Next, it returns to the state immediately after starting. Note: The check of the "FN"...
Page 247 Tests and Diagnostics The keyboard which can be tested is two kinds, "US Keyboard A4 Mode" and "US Keyboard A4 Mode+10Key Mode." When you test a keyboard with a ten key, choose "US Keyboard A4 Mode+10Key Mode" by the combo box of the keyboard layout upper left stage. 3-138 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 248 Tests and Diagnostics 3) Result judgment It is normal, if a keyboard test is done and all the keyboard layouts are eliminated. Press the "Pass" button with the judgment button at the upper right of a keyboard layout. Press the "Fail"...
Page 249 Tests and Diagnostics 3.34.6.13 Mouse Test 1) Test content The Mouse of PC is a test which judges whether it operates normally. ■Simple Mode / Detail Mode The same operation is carried out whichever it chooses. 2) Test screen If a mouse test start is carried out, the above-mentioned screen will be displayed. 3-140 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 250 Tests and Diagnostics 1) There is a test item to 1-9 of a mouse test screen. If applicable mouse operation is performed, a test item will disappear. Moreover, it is simultaneously displayed on the corresponding section of a right-hand side mouse illustration by coloring. 2) Press the "Refresh"...
Page 251 Tests and Diagnostics 3) Result judgment When all the test items of a mouse test disappear and it is normal, Please push the "Pass" button of a mouse test screen. Press the "Fail" button, when abnormal. A warning message is displayed, when the "Pass" button is pressed before the mouse test items 1-9 were all completed.
Page 252: Dos T&D
Tests and Diagnostics 3.35 DOS T&D 3.35.1 Configuration of Test Equipment The configuration of test equipment required for executing FreeDOS T&D is as follows: Note: Start the machine after connecting the FDD. If the FDD is connected to the machine after FreeDOS T&D started, it does not recognize the FDD. 3.35.1.1 Test device configuration Devices to be tested and Test devices (Abbreviated names)
Page 253 Tests and Diagnostics HDD ： Hard disk drive KB ： Keyboard FDD ： Floppy disk drive 3.35.1.2 Test program configuration This test program is configured as below: 3-144 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 254 Tests and Diagnostics 3.35.1.3 Test program list The following table lists test items included in each test. Test name Test No. Sub No. Test item SYSTEM DMI read MEMORY Conventional memory Protected mode Cache memory(on/off) Stress test KEYBOARD Pressed key code display DISPLAY VRAM read/write for VGA Gradation for VGA...
Page 255: How To Start T&D
3.35.2 How to start T&D 3.35.2.1 Diagnostics main menu Set the TOSHIBA Test & Diagnostic CD to the ODD drive and turn the power of the system If you select Freedos on the BOOT selection screen then the test program is loaded and the following test selection screen is displayed.
Page 256 Tests and Diagnostics 3.35.2.2 Diagnostics test menu If you select [1] in the main menu, the following test screen is displayed. Use the Up or Down cursor key to select your desired test item and press the [Enter] key. [1] - [9]: Select the subtest menu described in section 4-2-3. [88］: Specifies the number of error retries.
Page 257 Tests and Diagnostics 2) HARD DISK TEST The following message will appear. Select the Hard Disk DRIVE to be tested, then press Enter. ［1］：Drive 1 ［2］：Drive 2 ［3］：Drive 3 ［4］：Drive 4 ［0］：Drives 1 to 4 This message is used to select the error dump operation when a data compare error is detected.
Page 258 Tests and Diagnostics 3.35.2.3 Sub test menu If you select any test item from “DIAGNOSTICS TEST MENU”, the following sub menu is displayed. Use the Up or Down cursor key to select your desired item and press the [Enter] key. When you select any subtest item, you are taken to the test mode described in the detail of each test function in section 4-6.
Page 259: Test Operating Procedure
Tests and Diagnostics 3.35.3 Test Operating Procedure If you select any test item from the subtest menu and execute it, you are required to set the test mode. Set the test mode according to the following procedure. Use the Up and Down cursor keys to select an option for TEST LOOP and ERROR SOPT.
Page 260 Tests and Diagnostics ［［ HALT OPERATION ］］１：Test end …The test ended. Select a subtest. ２：Continue …The next step will be executed. ３：Retry …The error step will be retried. 3) Discontinuing a test If you press the [Ctrl] + [Alt] + [Break] keys during a test, the test is discontinued and the screen returns to the subtest menu described in section 3-31-4.2.3.
Page 261: Error Code Status
Tests and Diagnostics 3.35.4 Error Code Status If an error occurs during any test, one of the following error codes is displayed. Device Name Code Status Common DATA COMPARE ERROR SYSTEM ROM - CHECKSUM ERROR ROM - SERIAL ID WRITE ERROR ROM - NOT SUPPORTED PS-SYSTEM ROM - SENSING ERROR(AC-ADAPT) ROM - SENSING ERROR(1st Batt)
Page 262 Tests and Diagnostics FDD - RECORD NOT FOUND FDD - DMA OVERRUN ERROR FDD - DMA BOUNDARY ERROR FDD - CRC ERROR FDD - FDC ERROR FDD - SEEK ERROR FDD - TIME OUT ERROR FDD - NOT DRIVE ERROR FDD - MEDIA REMOVED FDD - WRITE BUFFER ERROR HDD - HDC NOT RESET ERROR...
Page 263: Task Function
Tests and Diagnostics 3.35.5 Task Function This T&D has three tasks, each of which has the following function. 3.35.5.1 Log Utilities（Task #5） This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk or USB memory The operation guide is displayed at the bottom of the screen and the error status names are displayed on the right side of the screen.
Page 264 Tests and Diagnostics 3.35.5.2 Running Test（Task #6） This test is a continuous test to be applied to the devices capable of unattended operation. The name of test device and the number of subtest being tested are displayed on the screen during a test.
Page 265 Tests and Diagnostics 3.35.5.3 FD & HD Utilities（Task #7） Run the utility on the floppy disk. If you select task No. [7], the following FDD utility selection menu is displayed. Use the Up and Down cursor keys to select your desired item and press the [Enter] key. If you press the [Esc] key or select [9], the screen returns to the main menu described in section 4.2.1.
Page 266: Detail Of Each Test Function
Tests and Diagnostics 3.35.6 Detail of Each Test Function 3.35.6.1 System Test 1) DMI data read This subtest displays the information in the Flash-ROM in the following format Model Name ： XXXXXXXX Version Number ： XXXXXXXX Serial Number ： XXXXXXXX Model Number ：...
Page 267 Tests and Diagnostics Test data = CCAA5533H, 8000000H Step 2: Byte Enable Test Write the data byte by byte to the initial address of the data in 64KB units and the initial data + 4, then read double words of the written data and compare the result with the original data.
Page 268 Tests and Diagnostics With regard to the test memory content, save the data to the test memory before the test and restore it to the former address after the test. (Coincidence assurance of the memory content) Details of Test Step 1: Sequential Write (Fixed pattern 1 MMX version 00005555AAAAFFFFh） : Sequential Read and Compare Step 3: Sequential Write (Fixed pattern 2 MMX version FFFFAAAA55550000h）...
Page 269 Tests and Diagnostics : JMP + Read and Compare Step 7: JMP＋Write (Address pattern 2) 1/4. 3/4 increment 0, 1/2 decrement : JMP＋Read and Compare Step11: Dword Transfer ( Data is an 32-bit shift data) : Step 11 bit-reversed pattern 3-160 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 270 Tests and Diagnostics 3.35.6.3 Keyboard Test 1) Pressed key code display When a key is pressed, the scan code, character code, and key top name are displayed on the screen in the format shown below. The 88 key (compatible with the 106 key) is not tested because this key operating in overseas mode uses the different character code table (Not for Japan model).
Page 271 Tests and Diagnostics 3.35.6.4 Display test Move the highlight bar to the subtest you want to execute and press Enter. 1) VRAM Read / Write for VGA This subtest writes the constant data (AAAAh and 5555h) to the video RAM. The data is read and compared to the original data.
Page 272 Tests and Diagnostics 3.35.6.5 Floppy Disk Test This subtest tests floppy disks. 1) Sequential read This subtest performs a Cyclic Redundancy Check (CRC) that continuously reads all the tracks (track: 0 to 39/0 to 79) on a floppy disk. 2) Sequential read / write This subtest continuously writes data pattern B5ADADh to all the tracks (track: 0 to 39/0 to 79) on a floppy disk.
Page 273 Tests and Diagnostics ［ FDC Status ］ XX XX XX XX XX FDC Status 0 ： Result Status 0 1 ： Result Status 1 2 ： Result Status 2 3 ： Cylinder Address 4 ： Head Address 5 ： Sector Address 6 ：...
Page 274 Tests and Diagnostics ［ Result Status 1 ］ EN ： End of Cylinder DE ： Data error OR ： Over run (DMAC) ND ： No data NW ： Not writable MA ： Missing address mark ［ Result Status 2 ］ CM ：...
Page 275 Tests and Diagnostics 3.35.6.6 Hard Disk Test 1) Sequential read This subtest performs a forward read operation (0 to Maximum) by 63 sectors. 2) Address uniqueness This subtest writes unique address data to each sector of the HDD track-by-track. The data written to each sector is then read and compared with the original data.
Page 276 Tests and Diagnostics 5) Partial read This subtest reads 1GB data that is in minimum, middle and maximum address of the HDD area. 6) Write specified address This subtest writes specified data to a specified cylinder and head on the HDD. 7) Read specified address This subtest reads data, which has been written to a specified cylinder and head on the HDD.
Page 277 Tests and Diagnostics [HDC Status] : P – 1F7h Name Function 0: HDC is ready. BSY（busy） 1: HDC is busy. 0: HDD does not accept the command. DRY（drive ready） 1: HDD is ready. 0: Write is successful DWF（write fault） 1: Write error 0: Seek error DSC（seek complete）...
Page 278 Tests and Diagnostics [Error register] Ｐ – 1F1h Name Function BBK（BadBlockMark） 0: Not used 1: Defective block mark detection. 0: No uncorrectable data error UNC（uncorrectable） 1: Uncorrectable data occurrence - - - 0: Not used 1: No ID field （identification） - - - 0: Not used ABT（about）...
Page 279 Tests and Diagnostics 3.35.6.7 Real timer test 1) Real time This subtest sets and displays the calendar or clock function. 2) Backup memory This subtest writes the data for 1bit ON (01, 02, 04…80h) and 1bit OFF (FE, FB, FB…7Fh) and AAh, 55h to 114 bytes of addresses from 0E to 7Fh, reads the written data and compares the result with the original data.
Page 280: Maintenance (Winpe&Freedos) Test Program Supplementary Information
Tests and Diagnostics 3.36 Maintenance (WinPE&FreeDos) Test Program Supplementary Information 3.36.1 Details of HTML Log File This section provides details of the HTML log file stored in the storage. 3.36.1.1 System Information The following table lists system information of the PC that Item Name Description Manufucture r...
Page 281 Tests and Diagnostics Physical Memory Capacity (MB) of memory which is installed in PC NetWork0 Name of LAN card. Only the first LAN card is displayed on the screen. MAC address Mac address of LAN card IDE HDD Name of the first IDE HDD and its capacity (GB) IDE HDD Name of the second IDE HDD and its capacity (GB) 1394 Disk...
Page 282 Tests and Diagnostics 3.36.1.3 Test Result The following table lists the test results. If an error occurs during a test, the line of the test on the screen is displayed in red color. Item Name Description Test Name Name of test Test Information Brief explanation of each test Pass Count...
Page 283: Maintenance (Winpe&Freedos) Test Program Supplementary Information
Tests and Diagnostics 3.37 Maintenance (WinPE&FreeDos) Test Program Supplementary Information 3.37.1 Outline Describes notices and restrictions on using this program 3.37.2 Notices and Restrictions (Win PE T&D) 1) CPU Stress When the CPU stress checkbox is checked, it is recommended that this test be conducted in the Simple mode.
Page 284: Notices And Restrictions (Freedos)
Tests and Diagnostics 6) Boot Media If the system is booted from the CD when both the CD and the USB memory that contain WinPE T&D are connected to the PC, T&D in the USB memory starts up. Also, when a bootable CD is not inserted in the CD drive when the system is booted from the USB memory, the ODD test fails with an error because the ODD test file is only contained in this CD.
Page 285: Chapter 4 Replacement Procedures
Chapter 4 Replacement Procedures [CONFIDENTIAL]...
Page 286 4 Replacement Procedures 4-ii [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 287 4 Replacement Procedures Chapter 4 Contents Overview........................4-1 Battery pack ......................4-11 PC card/ExperssCard/Bridge media/Smart card............4-13 4.3.1 PC card ....................4-13 4.3.2 ExperssCard ..................4-14 4.3.3 Bridge media(SD/SDHC memory card, miniSD/microSD Card, Memory Stick (PRO/PRO Duo), xD-PictureCard and MultiMediaCard)................. 4-15 4.3.4 Smart card ..................
Page 288 4 Replacement Procedures 4.25 LCD unit ........................4-86 4.26 Camera module/Wireless LAN antenna/3G antenna..........4-95 Figures Figure 4-1 Removing the battery pack ................4-11 Figure 4-2 Removing the PC card ................. 4-13 Figure 4-3 Removing the ExpressCard................4-14 Figure 4-4 Removing the Bridge media ................
Page 289 4 Replacement Procedures Figure 4-29 Removing the Bluetooth module ..............4-51 Figure 4-30 Removing the smart card slot ..............4-53 Figure 4-31 Removing the smart card holder ..............4-54 Figure 4-32 Removing the USB/sound board ..............4-56 Figure 4-33 Removing the microphone harness.............. 4-58 Figure 4-34 Removing the system board.................
Page 290 4 Replacement Procedures 4-vi [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 291: Overview
Replacement Procedures Overview This chapter describes the procedure for removing and replacing the field replaceable u nits (FRUs) in the PC. It may not be necessary to remove all the FRUs in order to replace on The chart below provides a guide as to which other FRUs must be removed before a particular FRU can be removed.
Page 292 Please pre pare re quired p arts in adv ance, when replacing the following ite Parts List ITEM PART NAME Quantity ITEM No COVER ASSY COVER ASSY TOUCH PAD Parts List ITEM PART NAME Quantity ITEM No LCD COVER ASSY LCD COVER CAMERA MODULE ASSY...
Page 293 m ain parts in this ma nual are indicate d in the part list by the following names. Parts List Manu al NAME PART NAM ITEM No System board PCB ASSY FG5INx Switch board PCB ASSY FG5SWx USB board PCB ASSY FG5USx Sound board PCB ASSY FG5SNx Pad b...
Page 294 DANGER: 1) Always use the genuine battery that is authorized by Toshiba or compatible with the unit. Since other battery packs have different specifications, they may be incompatible with the unit, and may burst or explode.
Page 295 Before You Begin Take note of the following points before starting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure f or removing the battery pack is described in section “4.2. Battery Pack”. 1.
Page 296 Disassembly Procedure Four main types of cable connector are used.  Pressure plate connector  Spring connector  Back flip connector  Normal pin connector For pressure plate connectors, slide the pressure plate holding tags on both sides of the plastic pressure plate on the connector and pull the cable out from the connector.
Page 297 Assembly Procedures After the computer has been disassembled and the part that caused the faul t has been repaired or replaced, the computer must be reassembled. Take note of the following general points when assembling the computer.  Take your time and follow the instructions carefully. Hurrying the assem bly work will only introduce new problems.
Page 298 CAUTION: Overtightening can damage components and screws; undertightening can result in electrical shorts or other damage if screws or components come loose. NOTE: Toshiba recommends that you use an electric screw driver for quick and easy operations.  M2 (2mm) 0.167 N·m (1.7 kgf·cm)
Page 299 Grip Color Some screws have a colored grip area to help you determine the length of the screw. [Normal grip]  Even numbered length screws: Brown  Odd numbered length screws : White Grip area  Special length screw: Blue [Special grip] ...
Page 300 Screw Notation To make maintenance of the computer easier, markings of the kinds of the screws including the types and lengths of the screws are indicated on the computer body. Format Screw type + Screw length (mm) ew shape B: Bind screw F: Flat head screw S: Super thin head screw T: Tapping screw...
Page 301: Battery Pack
Battery pack Removing the Battery pack o remove the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: Take care not to short circuit the terminals when removing the battery pack. Similarly, do not drop, knock, scratch, disassemble, twist, or bend the battery pack.
Page 302 Dispose always the used battery pack in accordance with the laws and ordinances of your local authority. Use only the batteries approved by Toshiba. NOTE: Check the battery’s terminals visually. If they are dirty, wipe them clean with a dry cloth.
Page 303: Pc Card/Expersscard/Bridge Media/Smart Card
PC card/ExperssCard/Bridge media/Smart card 4.3.1 PC card Removing the PC card o remove the PC card, follow the steps below and refer to Figure 4-2. CAUTION: Insert or remove a PC card in accordance with any instructions in their manual or the manuals of the computer system you are using. 1.
Page 304 4.3.2 ExpressCard Removing the ExpressCard o remove the ExpressCard, follow the steps below and refer to Figure 4-3. CAUTION: Insert or remove an ExpressCard in accordance with any instructions in the ExpressCard manual or the manuals of the computer system you are using. 1.
Page 305: Bridge Media
4.3.3 Bridge media (SD/SDH C memory card, miniSD/microSD Card, Memory Stick (PRO/PRO Duo), xD-PictureCard and MultiMediaCard) Removing the Bridge media o remove the Bridge media, follow the steps below and refer to Figure 4-4. CAUTION: Insert or remove a Bridge media in accordance with any instructions in each Bridge Media manual or the manuals of the computer system you are using.
Page 306: Smart Card
4.3.4 Smart Card Removing the Smart Card o remove the Smart Card, follow the steps below and refer to Figure 4-5. CAUTION: Insert or remove a Smart Card in accordance with any instructions in the Smart Card manual or the manuals of the computer system you are using. 1.
Page 307: Memory Module
Memory module Removing the Memory module To remove the memory module, confirm that the computer is shut down. Then follow the teps below and refer to Figure 4-6 and 4-7. CAUTION: When removing the m emory module, make sure the computer is powered off. Removing a memory module with the power on might damage the module or the computer itself.
Page 308 4. Open the left and right latches outside and remove the memory module(s). Latch Latch Slot B Slot A Memory module Figure 4-7 Removing the memory module 4-18 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 309 Installing the Memory module To install the memory module, confirm that the computer is shut down. Then follow the steps elow and refer to Figure 4-6 and 4-7. CAUTION: When installing the m emory module, make sure the computer is powered off. Inserting a memory module with the power on might damage the module or the computer itself.
Page 310: Sim Card
SIM card Removing the SIM card To remove the SIM card, follow the steps below and refer to Figure 4-8 and 4-9. 1. Slide the SIM card release latch in the direction as shown in the figure below. 2. Turn up the SIM card holder in the direction as shown in the figure below. SIM card holder SIM card release latch Figure 4-8 Removing the SIM card (1)
Page 311 3. Remove the SIM card from the SIM card holder. SIM card Figure 4-9 Removing the SIM card (2) Installing the SIM card To install the SIM card, follow the steps below and r efer to Figure 4-8 and 4-9. 1.
Page 312: Fin Cover
Fin cover NOTE: When repairing the PC, turn up the plastic film and clean the cooling fin with a vacuum cleaner or other cleaning tool. Plastic film Do not use cotton sticks and tweezers to remove dusts. It may cause the cooling module problem or dusts stuffed.
Page 313: Hdd
Removing the HDD To remove the HDD, follow the steps below and refer to Figure 4-11 and 4-12. CAUTION: Take care not to press on the top or bottom of a HDD. Pressure may cause the data loss or damage to the device. 1.
Page 314 4. Remove the following screws and separate the HDD and HDD holder.  4 M3.04C FLAT HEAD screw M3.04C FLAT HEAD M3.04C FLAT HEAD HDD Holder M3.04C FLAT HEAD Figure 4-12 Removing the HDD 4-24 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 315 Installing the HDD To install the HDD, follow the steps below and refer to Figure 4-11 and 4-12. 1. Set the HDD to the HDD Holder and secure them with the following screws.  4 M3.04C FLAT HEAD screw NOTE: When replacing the HDD holder with a new one, stick the gasket to the HDD holder in place.
Page 316: Optical Disk Drive (Dvd-Rom/Dvd-Super Multi Drive)
Optical disk drive (DVD-ROM/DVD-Super Multi drive) Removing the Optical disk drive o remove the optical disk drive, follow the steps below and refer to Figure 4-13 and 4-14. CAUTION: When the optical disk inside the optical disk drive can not be ejected because of some failure, open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole near the eject button.
Page 317 1. Remove the following screw securing the optical disk drive assembly.  1 M2.55B FLAT HEAD screw 2. Remove the optical disk drive assembly from the slot while pushing it in the direction as shown in the figure below. M2.55B FLAT HEAD Optical disk drive assembly Figure 4-13 Removing the optical disk drive assembly TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-27...
Page 318 3. Remove the following screws and ODD rear bracket from the optical disk drive.   2 M2.0 3C BIND screw ODD rear bracket Optical disk drive M2.03C BIND Figure 4-14 Removing the optical disk drive 4-28 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 319 Installing the Optical disk drive To install the Optical disk drive, follow the steps below and refer to Figure 4-13 to 4-15. 1. When installing a new optical disk drive, set the OD D bezel to the op tical disk drive while securing the latches.
Page 320: Keyboard
Keyboard Removing the Keyboard o remove the keyboard, follow the steps below and refer to Figure 4-16 to 4-19. CAUTION: As the keytop may fall out, when handling the keyboard always hold it by the frame and do not touch the keytop. 1.
Page 321 4. Remove the following screws securing the keyboard.  4 (with 10 key model) M2.03C BIND screw  2 (without 10 key model) 03C BIND screw Latch M2.03C BIND M2.03C BIND Latch Latch Figure 4-17 Removing the keyboard (with 10key model) (1) TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-31...
Page 322 Latch M2.03C BIND M2.03C BIND Latch Latch Figure 4-18 Removing the keyboard (without 10key model) (2) 4-32 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 323 5. Lift the top edge of the keyboard while releasing the latches and turn the keyboard face down on the palm rest. 6. Disconnect the keyboard flexible cable from the connector CN3230 on the system board and remove the keyboard. CN3230 Keyboard Keyboard flexible cable...
Page 324 Installing the Keyboard To install the keyboard, follow the steps below and refer to Figure 4-16 to 4-19. 1. Place the keyboard face down on the palm rest and connect the keyboard flexible cable to the connector CN3230 on the system board. 2.
Page 325: Sw Board
4.10 SW board Removing the SW board To remove the SW board, follow the steps below and refer to Figure 4-20. 1. Disconnect the SW board FFC from the connector CN9500 on the system board. 2. Push down the hook and slide the SW board in the direction as shown in the figure below to remove it.
Page 326 Installing the SW board o install the SW board, follow the steps below and refe r to Figure 4-20. 1. Slide the SW board into the guide to set it. 2. Connect the SW board FFC to the connector CN9500 on the system board. NOTE: Arrange the SW board FFC under the guide.
Page 327: Wireless Lan Card
4.11 Wireless LAN card Removing the Wireless LAN card To remove the wireless LAN card, follow the steps below and refer to Figure 4-21. 1. Disconnect the wireless LAN antenna cables from the wireless LAN card (white cable from “A” or “1” and black cable from “B” or “2”) using an antenna coaxial cable disconnector.
Page 328 Installing the Wireless LAN card To install the wireless LAN card, follow the steps below and refer to Figure 4-21. 1. Insert the wireless LAN card to the connector on the system board slantwise and press it to connect firmly. 2.
Page 329: Card
4.12 3G card Removing the 3G card To remove the 3G card, follow the steps below and refer to Figure 4-22. 1. Disconnect the 3G antenna cables from the connectors on the 3G card using an antenna coaxial cable disconnector. 2.
Page 330 Installing the 3G card To install the 3G card, follow the steps below and refer to Figure 4-22. 1. Insert the 3G card to the connector on the system board slantwise and press it to connect firmly. 2. Push down the 3G card and secure it with the following screws. ...
Page 331: Cover Assembly And Base Assembly
Replacement Procedu es 4.13 Cover assembly and Base assembly Removing the Cover assembly and Base assembly To remove the cover assembly and base assembly, follow the steps below and refer to Figure 4-23 to 4-25. 1. Close the display and turn over the computer. 2.
Page 332 4. Turn over the computer and open the display. 5. Turn up the insulator (LCD CONN INSULATOR) and disconnect the LCD harness from the connector CN5300 on the system board. 6. Disconnect the FS board FFC and camera harness from the connector CN9550 and CN9540 on the system board.
Page 333 8. Separate the cover assembly and base assembly while releasing the latches. Cover assembly Base assembly Figure 4-25 Removing the cover assembly and base assembly (3) CAUTION: When separating the cover assembly and base assembly, lift the cover assembly up right above. Otherwise, the computer may be damaged. TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-43...
Page 334 Installing the Cover assembly and Base assembly To install the cover assembly and base assembly, follow the steps below and refer to Figure 4-23 to 4-25. 1. Place the cover assembly on the base assembly and secure them with the following screws.
Page 335: Touch Pad/Fingerprint Sensor Board
4.14 Touch pad/Fingerprint sensor board Removing the Touch pad/Fingerprint sensor board To remove the touch pad/fingerprint sensor board, follow the steps below and refer to Figure 4-26 to 4-28. 1. Turn up the insulator (TPAD LOW INSULATOR) and remove the following screws. ...
Page 336 4. Remove the touch pad plate (with the fingerprint sensor board). 5. Remove the following screws and separate the fingerprint sensor board and touch pad plate.  2 M2.03C S-THIN HEAD screw Touch pad plate Fingerprint sensor board M2.0x3C S-THIN HEAD Figure 4-27 Removing the fingerprint sensor board 4-46 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 337 6. Peel off the touch pad. NOTE: Do not reuse the removed touch pad. Be sure to use a new touch pad. Touch pad Figure 4-28 Removing the touch pad (2) Please prepare required parts in advance, when replacing the following item. Parts List ITEM PART NAME...
Page 338 Installing the Touch pad/Fingerprint sensor board To install the touch pad/fingerprint sensor board, follow the steps below and refer to Figure 4-26 to 4-28. 1. Connect the touch pad button FFC to the connector on a new touch pad and stick the touch pad in place.
Page 339 3. Set the touch pad plate (with the fingerprint sensor board) in place. 4. Connect the dual button FFC to the connector on the touch pad. NOTE: When replacing the touch pad plate with a new one, stick the insulator (INSU TPAD LOW) to the touch pad plate in place.
Page 340 7. Stick the acetate tape in place. NOTE: Stick the acetate tape as shown in the figure below. <Normal KB model> <10key KB model> 4-50 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 341: Bluetooth Module
4.15 Bluetooth module Removing the Bluetooth module To remove the Bluetooth module, follow the steps below and refer to Figure 4-29. 1. Disconnect the Bluetooth harness from the connector CN4440 on the system board. 2. Remove the Bluetooth module from the guides. 3.
Page 342 Installing the Bluetooth module To install the Bluetooth module, follow the steps below and refer to Figure 4-29. 1. Connect the Bluetooth harness to the connector on the Bluetooth module. 2. Set the Bluetooth module along/under the guides and arrange the Bluetooth harness along/under the guides.
Page 343: Smart Card Slot
4.16 Smart card slot Removing the Smart card slot To remove the smart card slot, follow the steps below and refer to Figure 4-30 and 4-31. 1. Disconnect the smart card FPC from the connector CN9530 on the system board. 2.
Page 344 3. Remove the following screw securing the smart card holder.  1 M2.55C Tapping screw 4. Lift up the hook of the smart card holder in the direction as shown in the figure below to remove the smart card holder from the slot. M2.5x5C Tapping Smart card holder Hook...
Page 345 Installing the Smart card slot To install the smart card slot, follow the steps below and refer to Figure 4-30 and 4-31. 1. Slide the smart card holder into the slot until the hook is engaged. 2. Secure the smart card holder with the following screw. ...
Page 346: Usb/Sound Board
4.17 USB/Sound board Removing the USB/Sound board To remove the USB/sound board, follow the steps below and refer to Figure 4-32. 1. Disconnect the USB/sound harness from the connector CN9530 on the system board and connector CN9630 on the USB/sound board. 2.
Page 347 Installing the USB/Sound board To install the USB/sound board, follow the steps below and refer to Figure 4-32. 1. Set the USB/sound board into the slot of the base assembly. 2. Connect the USB/sound harness to the connector CN9530 on the system board and connector CN9630 on the USB/sound board.
Page 348: Microphone Harness
4.18 Microphone harness Removing the Microphone harness To remove the microphone harness, follow the steps below and refer to Figure 4-33. 1. Turn up the insulator (INSU SP HNS) and disconnect the microphone harness from the connector CN6070 on the system board. 2.
Page 349: System Board
4.19 System board CAUTION: When replacing with a new system board, the following procedures must be executed. (1) Before replacing the system board, execute subtest02 “DMI ggginformation save” in 3.3 Setting of the hardware configuration of gggChapter 3 Test program in order to save the DMI information from gggsystem board to floppy disk.
Page 350 Removing the System board To remove the system board, follow the steps below and refer to Figure 4-34. 1. Disconnect the speaker harness from the connector CN6150 on the system board. 2. Take out the DC-IN harness from the slot. 3.
Page 351 Installing the System board To install the system board, follow the steps below and refer to Figure 4-34. 1. Connect the DC-IN harness to the connector CN8800 on the back of the system board. 2. Set the system board on the base assembly in place and secure them with the following screws.
Page 352: Speaker
4.20 Speaker Removing the Speaker To remove the speaker, follow the steps below and refer to Figure 4-35. 1. Turn up the insulator (INSU SP HNS). 2. Remove the speakers (left and right) from the speaker slots and the speaker harness from the guides.
Page 353 Installing the Speaker To install the speaker, follow the steps below and refer to Figure 4-35. 1. Install the speakers (left and right) to the speaker slots. 2. Turn up the insulator (INSU SP HNS) and arrange the speaker harness into the guides.
Page 354 4.21 RGB harness/Serial port unit Removing the RGB harness/Serial port unit To remove the RGB harness/serial port unit, follow the steps below and refer to Figure 4-36. 1. Turn up the insulator (RGB SERIAL INSULATOR). 2. Remove the following screw and take out the RGB harness from the slot of the base assembly.
Page 355: Rgb Harness/Serial Port Unit
M2.5x5C Tapping RGB harness M2.5x5B FLAT HEAD Serial port unit Serial port FFC Insulator (RGB SERIAL INSULATOR) Figure 4-36 Removing the RGB harness/serial port unit TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-65 TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-65...
Page 356 Installing the RGB harness/ Serial port unit To install the RGB harness/serial port unit, follow the steps below and refer to Figure 4-36. 1. Connect the serial port FFC to the connector on the serial port unit. 2. Set the serial port unit into the slot of the base assem bly and secure it with the following screw.
Page 357 4. Turn up the insulator (RGB SERIAL INSULATOR) and arrange the serial port FFC and RGB harness in place. NOTE: In models without a serial port unit, stick the RGB HNS INSULATOR in place. TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-67...
Page 358 NOTE: When replacing a base assembly with a new one, set the following parts as shown in the figure below. (Docking port model) (Docking port model) 4-68 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 359 (Without docking port model) (3G antenna model) TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-69...
Page 360 (ODD model) (Wireless LAN antenna model) (Wireless LAN antenna model) 4-70 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 361 (TECRA S11 model) (TECRA S11 model) TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-71...
Page 362: Rtc Battery
.22 RTC battery CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the laws and ordinances of your local authority. Removing the RTC battery To remove the RTC battery, follow the steps below and refer to Figure 4-37. 1.
Page 363 Installing the RTC battery To install the RTC battery, follow the steps below and refer to Figure 4-37. 1. Set the RTC battery into the insulator (RTC BATT INSULATOR). 2. Stick the insulator (RTC BATT INSULATOR) on the system board. NOTE: Stick the RTC BATT INSULATOR on the system board as shown in the figure below.
Page 364: Cpu/Fin/Dc Fan
4.23 CPU/Fin/DC fan Removing the CPU/Fin/DC fan To remove the CPU/fin/DC fan, follow the steps below and refer to Figure 4-38 to 4-41. 1. Disconnect the fan harness from the connector CN3380 o n the system board. 2. Remove the following screws and fin (with the DC fan). ...
Page 365 M2.0x4B BIND M2.0x4B BIND Fan harness Fin (with DC fan) CN3380 Figure 4-39 Removing the fin/DC fan (external VGA model) (2) TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-75...
Page 366 3. Peel off the fan food. 4. Remove the following screws and separate the DC fan and fin.  2 M2.03C BIND screw M2.0x3C BIND Fan food DC fan Figure 4-40 Removing the fin/DC fan (3) 4-76 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 367 5. Unlock the CPU by turning the cam counterclockwise on the CPU socket by 180 degrees with a flat-blade screwdriver. 6. Remove the CPU. Figure 4-41 Removing the CPU CAUTION: When removing the CPU, lift it up right above. Otherwise, pins of the CPU may be damaged.
Page 368 Installing the CPU/fin/DC fan To install the CPU/fin/DC fan, follow the steps below and refer to Figure 4-38 to 4-43. 1. Make sure that the cam of the CPU socket is in the unlock (OPEN) position. 2. Set the CPU to the correct position in the CPU socket. Make sure the position of the CPU (triangle mark) is correct to avoid damaging pins on the CPU.
Page 369 4. When silicon grease is already applied to the fin, wipe them off with a cloth in advance. 5. Apply new grease (Shin-Etsu Chemical Co. X-23-7921-5) on the CPU using a special syringe as shown in the following figure. Apply quarter of scale (0.25ml) of grease evenly on the CPU chip.
Page 370 6. If there are already cool sheets on the VGA, ICs or fin remove the cool sheet. Stick new cool sheets on the fin in place. (only for the external VGA m odel) NOTE: Do not reuse the cool sheet. Be sure to use a new cool sheet. Stick the cool sheets as shown in the figure below.
Page 371 7. Set the DC fan to the fin and secure them with the following screws.  2 M2.03C BIND screw 8. Set the fan food to the DC fan. NOTE: Make sure that the guide rib of the fan food is engaged securely. Fan food 9.
Page 372: Mdc/Sim Board
4.24 MDC/SIM board Removing the MDC/SIM board To remove the MDC/SIM board, follow the steps below and refer to Figure 4-44 and 4-45. 1. Disconnect the SIM board FFC from the connector CN9570 on the system board and CN9670 on the SIM board. 2.
Page 373 M2.0x6B BIND M2.0x4B BIND SIM board CN9670 SIM board FFC CN9570 RJ11 harness Figure 4-44 Removing the MDC/SIM board TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-83...
Page 374 6. Disconnect the RJ11 harness from the connector CN3010 on the system board. 7. Take out the RJ11 harness from the RJ11 harness holder. 8. Remove the following screw securing the RJ11 h arness holder.  1 M2.04B BIND screw 9.
Page 375 Installing the MDC/SIM board To install the MDC/SIM board, follow the steps below and refer to Figure 4-44 and 4-45. 1. Set the RJ11 harness holder to the system board while engaging the latches. 2. Secure the RJ11 harness holder with the following screw. ...
Page 376: Lcd Unit
Replacement Procedures 4.25 LCD unit Removing the LCD unit To remove the LCD unit, follow the steps below and refer to Figure 4-46 to 4-51. 1. Turn up the insulators (INSU ANT HLD L and INSU ANT HLD R) and release the harnesses.
Page 377 NOTE: In models with 3G antennas, insulator (3G HNS HLD INSULATOR) and spacer (3G HNS SPACER) are mounted as shown in the figure below. TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-87...
Page 378 2. Remove the following screws and separate the LCD assembly and cover assembly.  4 M2.55B FLAT HEAD screw  2 M2.512B FLAT HEAD scr M2.5x5B FLAT HEAD M2.5x12B FLAT HEAD M2.5x5B FLAT HEAD M2.5x12B FLAT HEAD LCD assembly Cover assembly Guide Figure 4-47 Removing the LCD unit (2) 4-88 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 379 3. Peel off the LCD mask cushions and remove the following screws.  2 M2.55B FLAT HEAD screw 4. Remove the LCD mask while releasing the latches. NOTE: Release the lower part of the latches first. LCD mask cushion M2.5x5B FLAT HEAD LCD mask LCD mask cushion M2.5x5B FLAT HEAD...
Page 380 5. Turn up the insulator (LCD HNS INSULATOR) 6. Remove the following screws and stand the LCD unit. Be careful that the LCD harness is connected to the connector on the back of the LCD unit.  4 M2.55C Tapping screw M2.5x5C Tapping LCD unit M2.5x5C Tapping...
Page 381 7. Release the LCD harness from the guides of the LCD cover. 8. Peel the pull tape and disconnect the LCD harness from the connector on the LCD unit. LCD unit Pull tape Guide LCD harness Figure 4-50 Removing the LCD harness TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-91...
Page 382 9. Remove the following screws and separate the LCD unit and Brake hinges.  2 M2.03C S-THIN HEAD screw M2.0x3C S-THIN HEAD Brake hinge L Brake hinge R LCD unit M2.0x3C S-THIN HEAD Figure 4-51 Removing the LCD unit (4) 4-92 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 383 Installing the LCD unit To install the LCD unit, follow the steps below and refer to Figure 4-46 to 4-51. 1. Set the brake hinges to the LCD unit and secure them with the following screws.  2 M2.03C S-THIN HEAD screw 2.
Page 384 9. Set the LCD assembly to the guides of the cover assem bly and secure them with the following screws.  4 M2.55B FLAT HEAD screw  2 M2.512B FLAT HEAD screw 10. Turn up the insulators (INSU ANT HLD L and INSU ANT HLD R) and arrange the harnesses to the guides of the cover assembly.
Page 385 4.26 Camera module/Wireless LAN antenna/3G antenna Removing the Camera module/Wireless LAN antenna/3G antenna To remove the camera module/wireless LAN antenna/3G antenna, follow the steps below and refer to Figure 4-52 and 4-53. 1. Disconnect the camera harness from the connector on the camera module. 2.
Page 386 3. Peel off the wireless LAN antennas, 3G antennas and camera harness from the LCD cover. NOTE: Do not reuse the removed wireless LAN antennas and 3G antennas. Be sure to use new wireless LAN antenna or 3G antenna. Wireless antenna (whi 3G antenna (red) Wireless antenna (black) Camera harness...
Page 387 Installing the Camera module/Wireless LAN antenna/3G antenna To install the camera module/wireless LAN antenna/3G antenna, follow the steps below and refer to Figure 4-52 and 4-53. 1. Stick new wireless LAN antennas in place. 2. Arrange the wireless LAN antenna cables in place. 3.
Page 388 6. Stick the camera cushion and square cushion on the LCD cover. NOTE: Stick the camera cushion and square cushion as shown in the figure below. 7. Connect the camera harness to the connector on the camera module and stick the camera module in place.
Page 389 CAUTION: Replacing the wireless LAN antennas, 3G antenna and camera module with care of the followings: TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-99...
Page 390 Arrange the harnesses as shown in the figure below. Stick the aluminum sheet for the 3G model only. 4-100 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 391 Arrange the harnesses as shown in the figure below. TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] 4-101...
Page 392 Arrange the harnesses as shown in the figure below. 4-102 [CONFIDENTIAL] TECRA A11/S11/P11 Satellite Pro S500 Series Maintenance Manual (960-784)
Page 393: Appendices
Appendix A Handling the LCD Module Appendices Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1.
Page 394 Appendices Appendix A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent.
Page 395 Appendix A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge.
Page 396 Appendices Appendix A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9.
Page 397 Appendix A Handling the LCD Module Appendices 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization. TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 398 Appendices Appendix A Handling the LCD Module [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 399: Appendix B Board Layout
Appendix B Board Layout Appendices Appendix B Board Layout B.1 System board (FHNSY*) Front View Figure B-1 System board (FHNSY*) layout (front) TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 400 Appendices Appendix B Board Layout Table B-1 System board (FHNSY*) connectors and ICs (front) Number Name CN2110 PC CARD interface connector CN2170 Smart Card interface connector CN2600 PCI-E MINI CARD interface connector CN3110 It is debugging port for development only CN3230 KB interface connector CN4440...
Page 401 Appendix B Board Layout Appendices B.2 System board (FHNSY*) Back View Figure B-2 System board (FHNSY*) layout (back) TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 402 Appendices Appendix B Board Layout Table B-2 System board (FHNSY*) connectors and ICs (back) Number Name CN1400 Memory A connector CN1410 Memory B connector CN1900 SATA HDD interface connector CN1910 SDD interface connector (Not used) CN1950 SATA ODD interface connector CN1970 eSATA/USB interface connector CN2300...
Page 403 Appendix B Board Layout Appendices B.3 System board (FHVSY*) Front View Figure B-3 System board (FHVSY*) layout (front) TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 404 Appendices Appendix B Board Layout Table B-3 System board (FHVSY*) connectors and ICs (front) Number Name CN2110 PC CARD interface connector CN2170 Smart Card interface connector CN2600 PCI-E MINI CARD interface connector CN3110 It is debugging port for development only CN3230 KB interface connector CN4440...
Page 405 Appendix B Board Layout Appendices B.4 System board (FHVSY*) Back View Figure B-4 System board (FHVSY*) layout (back) TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 406 Appendices Appendix B Board Layout Table B-4 System board (FHVSY*) connectors and ICs (back) Number Name CN1400 Memory A connector CN1410 Memory B connector CN1900 SATA HDD interface connector CN1910 SDD interface connector (Not used) CN1950 SATA ODD interface connector CN1970 eSATA/USB interface connector CN2300...
Page 407 Appendix B Board Layout Appendices B.5 USB/Sound- Jack board (FHNJK*/FHVJK*) View (front) (back) Figure B-5 USB/Sound- Jack board (FHNJK*/FHVJK*) layout (front/back) Table B- 5 USB/Sound- Jack board (FHNJK*/FHVJK*) connector (front/back) Number Name CN4621 USB interface connector CN4622 USB interface connector J6051 Microphone connector J6310...
Page 408 Appendices Appendix B Board Layout B.6 Finger/Pad Button board (FHNFS*/FHVFS*) View (front) (back) Figure B-6 Finger/Pad Button board (FHNFS*/FHVFS*) layout (front/back) Table B-6 Finger/Pad Button board (FHNFS*/FHVFS*) connector (front) Number Name CN3240 Dual point interface connector CN9650 System board interface connector B-10 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 409 Appendix B Board Layout Appendices B.7 SIM board (FHNSM*/FHVSM*) View: Not uued (front) (back) Figure B-7 SIM board (FHNSM*/FHVSM*) layout (front/back) Table B-7 SIM board (FHNSM*/FHVSM*) connector (back) Number Name IS2620 SIM board interface connector CN9670 System board interface connector TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] B-11...
Page 410 Appendices Appendix B Board Layout B-12 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 411: Appendix C Pin Assignments
Appendix C Pin Assignments Appendices Appendix C Pin Assignments System board (FHNSY*/FHVSY*) CN1400 Memory A connector(200-pin) Table C- 1 Memory A connector (200-pin) (1/3) Pin No. Signal Name Pin No. Signal Name MR0R75-B0V ADQ00-B1P ADQ05-B1P ADQ04-B1P ADQ01-B1P ADQS0-B1N ADM0-B1P ADQS0-B1P ADQ06-B1P ADQ03-B1P ADQ07-B1P...
Page 412 Appendices Appendix C Pin Assignments Table C-1 Memory A connector (200-pin) (2/3) Pin No. Signal Name Pin No. Signal Name ADQS3-B1N ADM3-B1P ADQS3-B1P ADQ31-B1P ADQ30-B1P ADQ26-B1P ADQ27-B1P ACKE0-B1P ACKE1-B1P 1R5-B1V 1R5-B1V AMA15-B1P ABS2-B1P AMA14-B1P 1R5-B1V 1R5-B1V AMA12-B1P AMA11-B1P AMA09-B1P AMA07-B1P 1R5-B1V 1R5-B1V AMA08-B1P...
Page 413 Appendix C Pin Assignments Appendices Table C-1 Memory A connector (200-pin) (3/3) Pin No. Signal Name Pin No. Signal Name ADQS4-B1N ADM4-B1P ADQS4-B1P ADQ38-B1P ADQ39-B1P ADQ35-B1P ADQ34-B1P ADQ41-B1P ADQ44-B1P ADQ40-B1P ADQ45-B1P ADQS5-B1N ADM5-B1P ADQS5-B1P ADQ47-B1P ADQ46-B1P ADQ42-B1P ADQ43-B1P ADQ53-B1P ADQ48-B1P ADQ49-B1P ADQ52-B1P ADQS6-B1N...
Page 414 Appendices Appendix C Pin Assignments CN1410 Memory B connector (200-pin) Table C- 2 Memory B connector (200-pin) (1/3) Pin No. Signal Name Pin No. Signal Name MRVREF-B0V BDQ00-B1P BDQ05-B1P BDQ04-B1P BDQ01-B1P BDQS0-B1N BDM0-B1P BDQS0-B1P BDQ06-B1P BDQ03-B1P BDQ07-B1P BDQ02-B1P BDQ12-B1P BDQ09-B1P BDQ13-B1P BDQ08-B1P BDQS1-B1N...
Page 415 Appendix C Pin Assignments Appendices Table C-2 Memory B connector (200-pin) (2/3) Pin No. Signal Name Pin No. Signal Name BDQS3-B1N BDM3-B1P BDQS3-B1P BDQ31-B1P BDQ30-B1P BDQ26-B1P BDQ27-B1P BCKE0-B1P BCKE1-B1P 1R5-B1V 1R5-B1V BMA15-B1P BBS2-B1P BMA14-B1P 1R5-B1V 1R5-B1V BMA12-B1P BMA11-B1P BMA09-B1P BMA07-B1P 1R5-B1V 1R5-B1V BMA08-B1P...
Page 416 Appendices Appendix C Pin Assignments Table C-2 Memory B connector (200-pin) (3/3) Pin No. Signal Name Pin No. Signal Name BDQS4-B1N BDM4-B1P BDQS4-B1P BDQ38-B1P BDQ39-B1P BDQ35-B1P BDQ34-B1P BDQ41-B1P BDQ44-B1P BDQ40-B1P BDQ45-B1P BDQS5-B1N BDM5-B1P BDQS5-B1P BDQ47-B1P BDQ46-B1P BDQ42-B1P BDQ43-B1P BDQ53-B1P BDQ48-B1P BDQ49-B1P BDQ52-B1P BDQS6-B1N...
Page 417 Appendix C Pin Assignments Appendices CN1900 SATA HDD interface connector (20-pin) Table C- 3 SATA HDD interface connector (20-pin) Pin No. Signal Name Pin No. Signal Name ZSTTHD-P1P ZSTTHD-P1N ZSTRHD-P1N ZSTRHD-P1P GND(W1900) CN1910 2 SSD interface connector (20-pin): Not used Table C- 4 2nd SSD interface connector (20-pin) Pin No.
Page 418 Appendices Appendix C Pin Assignments CN1950 SATA ODD interface connector (13-pin) Table C- 5 SATA ODD interface connector (23-pin) Pin No. Signal Name Pin No. Signal Name ZSTTOD-P1P ZSTTOD-P1N ZSTROD-P1N ZSTROD-P1P ODDDET-P3N CN1970 eSATA/USB interface connector (20-pin) Table C- 6 eSATA/USB interface connector (20-pin) Pin No.
Page 419 Appendix C Pin Assignments Appendices CN2110 PC CARD interface connector (70-pin) Table C- 7 PC CARD interface connector (70-pin)(1/2) Pin No. Signal Name Pin No. Signal Name ACAD00-PYP ACAD01-PYP ACAD03-PYP ACAD05-PYP ACAD07-PYP ACCBE0-PYN ACAD09-PYP ACAD11-PYP ACAD12-PYP ACAD14-PYP ACCBE1-PYN ACPAR-PYP ACPERR-PYN ACGNT-PYN ACINT-PYN MCVCCA-PYV...
Page 420 Appendices Appendix C Pin Assignments CN2170 Smart Card interface connector (10-pin) Table C- 8 Smart Card interface connector (10-pin) Pin No. Signal Name Pin No. Signal Name EGATE-P3N SCC4-PYP SCIO-PYP SCCLK-PYP SCDET-P3N SCVCC-PYV SCRST-PYN C-10 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 421 Appendix C Pin Assignments Appendices CN2300 DOCKING interface connector (140-pin) Table C- 9 DOCKING interface connector (140-pin) (1/3) Pin No. Signal Name Pin No. Signal Name DCOUT DCOUT DOCDT1-S3N ZUSBDC-E3P ZUSBDC-E3N ZDVTX2-P3P ZDVTX2-P3N ZDVTX1-P3P ZDVTX1-P3N DVIDET-P3N DCOUT DCOUT DPCONF-S5P XDVTCK-P3N XDVTCK-P3P ZDVTX0-P3P ZDVTX0-P3N...
Page 422 Appendices Appendix C Pin Assignments Table C-9 DOCKING interface connector (140-pin) (2/3) Pin No. Signal Name Pin No. Signal Name ZBIDCN-EXN ZBIDCP-EXP DCOUT DCOUT PWRSW-S3N DOCVON-S3P DILSON-S3P NVBBLU-PXP NVBRED-PXP NVBSDA-P3P NVBSCL-P3P ACT-E3N －－－ ZBIDBN-EXN ZBIDBP-EXP ZBIDAN-EXN ZBIDAP-EXP DCOUT DCOUT EJCTRQ-S3N DHSYNC-P3P...
Page 423 Appendix C Pin Assignments Appendices Table C-9 DOCKING interface connector (140-pin) (3/3) Pin No. Signal Name Pin No. Signal Name DSKDC TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] C-13...
Page 424 Appendices Appendix C Pin Assignments C.10 CN2600 PCI-E Mini CARD interface connector (52-pin) Table C- 10 PCI-E Mini CARD interface connector (52-pin) Pin No. Signal Name Pin No. Signal Name PEWAKE-E3N WLAN-E3V WCHDAT-P3P WCHCLK-P3P 1R5-P1V WLXRQ-E3N XPEWL-P0N XPEWL-P0P WLRFON-S3N PLTRS1-E3N ZERWL-P1N WLAN-E3V ZERWL-P1P...
Page 425 Appendix C Pin Assignments Appendices C.11 CN2610 PCI-E Mini(3G) CARD interface connector (52-pin) Table C- 11 PCI-E Mini(3G/ROBSON) CARD interface connector (52-pin) Pin No. Signal Name Pin No. Signal Name UIMPWR-E3V UIMDAT-E3P UIMCLK-E3P UIMRST-E3P 3GRFON-S3N PLTRS0-E3N MINDET-P3N ZUSB3G-E3N ZUSB3G-E3P 3GLED-E3P TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] C-15...
Page 426 Appendices Appendix C Pin Assignments C.12 CN3230 Keyboard interface connector (34-pin) Table C- 12 Keyboard interface connector (34-pin) Pin No. Signal Name Pin No. Signal Name KBSC16-S3N / SPY-PXP SP-GND SPX-PXP / KBSC17-S3N SP-P5V KBSC14-S3N KBSC13-S3N KBSC12-S3N KBSC15-S3N KBSC07-S3N KBSC11-S3N KBSC01-S3N KBSC10-S3N KBSC08-S3N...
Page 427 Appendix C Pin Assignments Appendices C.14 CN3010 MDC module interface connector (12-pin) Table C- 14 MDC interface connector (12-pin) Pin No. Signal Name Pin No. Signal Name AZSDO1-E3P AZSYC1-E3P IC3010-1 AZRST1-E3N XAZBC1-E3P C.15 CN3011 MDC interface connector (2-pin) Table C- 15 MDC interface connector (12-pin) Pin No.
Page 428 Appendices Appendix C Pin Assignments C.17 CN4620 USB interface connector (4-pin) Table C- C- 17USB interface connector (4-pin) Pin No. Signal Name Pin No. Signal Name USB1PS-E5V ZUSBCA-E3N ZUSBCA-E3P C.18 CN4440 Bluetooth interface connector (7-pin) Table C- 18 Bluetooth2 interface connector (7-pin) Pin No.
Page 429 Appendix C Pin Assignments Appendices C.19 CN5300 LCD interface connector (40-pin) Table C- 19 LCD interface connector (40-pin) Pin No. Signal Name Pin No. Signal Name PNL-P3V PNL-P3V TSCL-P3P TSDA-P3P ZNATX0-PYN ZNATX0-PYP ZNATX1-PYN ZNATX1-PYP ZNATX2-PYN ZNATX2-PYP XNACK0-PYP XNACK0-PYN ZNATX4-PYN ZNATX4-PYP ZNATX5-PYP ZNATX5-PYN ZNATX6-PYN...
Page 430 Appendices Appendix C Pin Assignments C.20 CN6150 Speaker interface connector (4-pin) Table C- 20 Speaker interface connector (4-pin) Pin No. Signal Name Pin No. Signal Name SPOTL-PXN SPOTL-PXP SPOTR-PXP SPOTR-PXN C.21 CN6070 Int-Mic interface connector (2-pin) Table C- 21 Int-Mic interface connector (2-pin) Pin No.
Page 431 Appendix C Pin Assignments Appendices C.24 CN8810 Battery connector (10-pin) Table C- 24 Battery connector (10-pin) Pin No. Signal Name Pin No. Signal Name Q8811-1pin BTMP1 Q8811-4pin PSCL-S5P PSDA-S5P DBT1OV-S5N C.25 CN9540 WebCam interface connector (6-pin) Table C- 25 WebCam interface connector (6-pin) Pin No.
Page 432 Appendices Appendix C Pin Assignments C.27 CN5690 Displayport interface connector (20-pin) Table C- 27 Displayport interface connector (45-pin) Pin No. Signal Name Pin No. Signal Name HPDDPG-S3P ZDPTX0-P1P DPMODE-P3P ZDPTX0-P1N ZDPTX1-P1P ZDPTX3-P1P ZDPTX1-P1N ZDPTX3-P1N ZDPTX2-P1P ZDPAUX-PYP ZDPTX2-P1N ZDPAUX-PYN IC690-8 C-22 [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 433 Appendix C Pin Assignments Appendices C.28 IS2140 MEDIA BRIDGE interface connector (45-pin) Table C- 28 MEDIA BRIDGE interface connector (45-pin) Pin No. Signal Name Pin No. Signal Name FMC11-P3P FMC10-P3P FMC09-P3P FMC08-P3P FMC07-P3P FMMSCK-P3P FMC10-P3P FMCD1-P3N FMC08-P3P FMC05-P3P FMC02-P3P FMC00-P3P FMC05-P3P FMC04-P3P FMC03-P3P...
Page 434 Appendices Appendix C Pin Assignments C.29 IS2520 EXPRESS CARD interface connector (40-pin) (Case of FHNSY*) Table C- 29 EXPRESS CARD interface connector (26-pin) Pin No. Signal Name Pin No. Signal Name ZUSBEX-E3N GND ZUSBEX-E3P CPUSB-E3N CRD-E3V CRD-E3V CRD1R5-P1V CRD1R5-P1V PEWAKE-E3N CRD-E3V CRDRST-E3N CRD-P3V...
Page 435 Appendix C Pin Assignments Appendices C.30 CN9560 EXPRESS CARD interface connector (40-pin) (Case of FHVSY*) Table C- 30 EXPRESS CARD interface connector (26-pin) Pin No. Signal Name Pin No. Signal Name ZUSBEX-E3N ZUSBEX-E3P CPUSB-E3N CRD-E3V CRD-E3V CRD1R5-P1V CRD1R5-P1V PEWAKE-E3N CRD-E3V CRDRST-E3N CRD-P3V CRD-P3V...
Page 436 Appendices Appendix C Pin Assignments C.31 CN9700 FELICA interface connector (6-pin) :Not used Table C- 31 FELICA interface connector (6-pin) Pin No. Signal Name Pin No. Signal Name Q9700-1 ZUSBP5-E3N ZUSBP5-E3P C.32 CN9300 RTCVCC interface connector (3-pin) Table C- 32 RTCVCC interface connector (3-pin) Pin No.
Page 437 Appendix C Pin Assignments Appendices C.34 CN9500 P-SW interface connector (8-pin) Table C- 34 P-SW interface connector connector (8-pin) Pin No. Signal Name Pin No. Signal Name VOLUP-S3N VOLDWN-S3N SERDBG-P3N BTN5ML-P3N PNLOFF-S3N GPBTNB-S3N GPBTNA-S3N PWRSW-S3N TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] C-27...
Page 438 Appendices Appendix C Pin Assignments C.35 CN9530 FHNJK*/FHVJK* board interface connector (40-pin) Table C- 35 FHNJK*/FHVJK* board interface connector (40-pin) Pin No. Signal Name Pin No. Signal Name ZUSBP1-E3N ZUSBP1-E3P ZUSBP2-E3P ZUSBP2-E3N USBON0-E5N USBOC0-E3N EMICB-P2V DETCTA-P4N A-GND EMICIN-PXP A-GND HEADR-PXP A-GND HEADL-PXP A-GND...
Page 439 Appendix C Pin Assignments Appendices C.36 CN9550 FHNFS*/ FHVFS* board interface connector (14-pin) Table C- 36 FHNFS*/ FHVFS* board interface connector (14-pin) Pin No. Signal Name Pin No. Signal Name SP-GND SPY-PXP SPX-PXP SP-P5V IPDCLK-P5P IPDDAT-P5P ZUSBFS-E3P ZUSBFS-E3N FGSPON-S3N C.37 CN9570 FHNSM*/FHVSM* board interface connector (10-pin) Table C- C- 37 FHNSM*/FHVSM* board interface connector (10-pin) Pin No.
Page 440 Appendices Appendix C Pin Assignments USB/Sound- Jack board (FHNJK*/FHVJK*) C.38 CN9630 System board interface connector (40-pin) Table C- 38 System board interface connector (40-pin) Pin No. Signal Name Pin No. Signal Name A-GNG HEADL-PXP A-GNG HEADR-PXP A-GNG EMICIN-PXP A-GNG DETCTA-P4N EMICB-P2V USBOC0-E3N USBON0-E5N...
Page 441 Appendix C Pin Assignments Appendices C.39 CN4621 USB interface connector (4-pin) Table C- 39 USB interface connector (4-pin) Pin No. Signal Name Pin No. Signal Name USB0PS-E5V ZUSBP2-E3N ZUSBP2-E3P C.40 CN4622 USB interface connector (4-pin) Table C- 40 USB interface connector (4-pin) Pin No.
Page 442 Appendices Appendix C Pin Assignments Finger/Pad Button board (FHNFS*/FHVFS*) C.43 CN3240 Dual point interface connector (12-pin) Table C- 43 Dual point interface connector (12-pin) Pin No. Signal Name Pin No. Signal Name TPBTNL-P5N TPBTNR-P5N SP-P5V SPX-PXP SPY-PXP SP-GND IPDCLK-P5P IPDDAT-P5P C.44 CN9650 System board interface connector (14-pin) Table C- 44 System board interface connector (14-pin) Pin No.
Page 443 Appendix C Pin Assignments Appendices SIM board (FHNSM*/FHVSM*) C.45 CN9670 System board interface connector (10-pin) Table C- 45 System board interface connector (10-pin) Pin No. Signal Name Pin No. Signal Name UIMPWR-E3V UIMRST-E3P UIMCLK-E3P UIMDAT-E3P C.46 IS2620 SIM board interface connector (7-pin) Table C- 46 SIM board interface connector (10-pin) Pin No.
Page 444 Appendix D Keyboard Scan/Character Codes Appendices Appendix. D Appendix D Keyboard Scan/Character Codes Scan Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Keytop Note Make Break Make Break ‘ ~ 7 & BkSp TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)[CONFIDENTIAL]...
Page 445 Appendices Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Keytop Note Make Break Make Break Caps Lock ‘ “ Enter Shift (L) No.102 , < . > Shift (R) [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 446 Appendix D Keyboard Scan/Character Codes Appendices Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Keytop Note Make Break Make Break Ctrl Alt (L) Space ALT (R)  Home   PgUp PgDn ...
Page 447: Appendix D Keyboard Scan/Character Codes
Appendices Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Keytop Note Make Break Make Break PrintSc Pause — — — — Notes: 1. * Scan codes differ by mode. 2.
Page 448 Appendix D Keyboard Scan/Character Codes Appendices Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Make Break Make Break E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12...
Page 449 Appendices Appendix D Keyboard Scan/Character Codes Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Make Break Make Break E0 2A E0 52 E0 D2 E0 AA E0 12 70 E0 F0 E0 F0 12 E0 2A E0 53 E0 D3 E0 AA E0 12 71 E0 F0 E0 F0 12...
Page 450 Appendix D Keyboard Scan/Character Codes Appendices Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Keytop Make Break Make Break (–) Table D-6 No.124 key scan code Code set 1 Code set 2 Shift Make Break Make Break Prt Sc...
Page 451 Appendices Appendix D Keyboard Scan/Character Codes Table D-7 No.126 key scan code Shift Code set 1 Code set 2 Make Make Pause Common* E1 1D E1 F0 Ctrl* E0 46 7E E0 F0 *: This key generates only make codes. [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 452: Appendix E Key Layout
Appendix E Key Layout Appendices Appendix E Key Layout United Kingdom (UK) Keyboard (+10 key) Figure E-1 UK keyboard United States (US) Keyboard (+10 key) Figure E-2 US keyboard TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 453 Appendices Appendix E Key Layout Japan (JP) Keyboard (+10 key) Figure E-3 JP keyboard [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 454 Appendix E Key Layout United Kingdom (UK) Keyboard Figure E-4 UK keyboard United States (US) Keyboard Figure E-5 US keyboard TECRA 9100 Maintenance Manual (960-347)
Page 455 Appendices Appendix E Key Layout Japan (JP) Keyboard Figure E-6 JP keyboard [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 456: Appendix F Wiring Diagrams
Appendix F Wiring diagrams Appendices Appendix F Wiring diagrams RGB Monitor Loopback Connector Figure F-1 RGB Monitor Loopback Connector LAN Loopback Connector Figure F-2 LAN Loopback Connector TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL] F-1...
Page 457 Appendices Appendix F Wiring diagrams F-2 [CONFIDENTIAL]TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 458: Appendix Gbios Rewrite Procedures
Appendix G BIOS rewrite procedures Appendices Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool:  BIOS/EC/KBC rewriting disk Rewriting the BIOS 1.
Page 459 Appendices Appendix G BIOS rewrite procedures [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)
Page 460: Appendix Hec/Kbc Rewrite Procedures
Appendix H EC/KBC rewrite procedures Appendices Appendix H Appendix H EC/KBC Rewrite Procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. It is necessary to rewrite the EC/KBC system program when the following changes are made. 1.
Page 461: Appendix I Reliability
Appendix I Reliability Appendices Appendix I Reliability Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) in maximum configuration. Table I-1 MTBF Time (hours) 5,377.2 ｈ 10GC 5,344.8 ｈ TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784) [CONFIDENTIAL]...
Page 462 Appendices Appendix I Reliability [CONFIDENTIAL] TECRA A11/S11/P11/Satellite Pro S500 Series Maintenance Manual (960-784)

This manual is also suitable for:

Tecra s11 series Tecra p11 series Satellite pro s500 series

Toshiba TECRA A11 Series Maintenance Manual

Table of Contents

Chapter 1 Hardware Overview

Table of Contents

Chapter 2 Troubleshooting Procedures

Table of Contents

Chapter 3 Tests and Diagnostics

Table of Contents

Chapter 4 Replacement Procedures

Table of Contents

Appendix A Handling the LCD Module

Appendix B Board Layout

Appendix C Pin Assignments

Appendix D Keyboard Scan/Character Codes

Appendix E Key Layout

Appendix F Wiring Diagrams

Appendix Gbios Rewrite Procedures

Appendix Hec/Kbc Rewrite Procedures

Appendix I Reliability

Quick Links

Chapters

Troubleshooting

Related Manuals for Toshiba TECRA A11 Series

Summary of Contents for Toshiba TECRA A11 Series