1. Manuals
  2. Brands
  3. Garland Manuals
  4. Ranges
  5. SRW286A
  6. Installation & operating instructions manual

Garland SRW286A Installation & Operating Instructions Manual

Starfire sentry combination range
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION & OPERATING
GARLAND® STARFIRE SENTRY COMBINATION
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER
FLAMMABLE VAPORS OR LIQUIDS IN THE
VICINITY OF THIS OR ANY OTHER APPLIANCE.
KEEP APPLIANCE AREA FREE AND CLEAR
FROM COMBUSTIBLES.
THIS APPLIANCE IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR YOUR PROTECTION
AGAINST SHOCK HAZARD. IT SHOULD BE PLUGGED DIRECTLY INTO A PROPERLY GROUNDED THREE-
PRONG RECEPTACLE. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THIS PLUG
DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION AIR TO THIS APPLIANCE.
PLEASE READ ALL SECTIONS OF THIS MANUAL AND RETAIN FOR FUTURE REFERENCE.
THIS PRODUCT HAS BEEN CERTIFIED AS COMMERCIAL COOKING EQUIPMENT AND MUST BE INSTALLED BY
PROFESSIONAL PERSONNEL AS SPECIFIED.
For Your Safety:
Post in a prominent location, instructions to be followed in the event the user smells gas.
This information shall be obtained by consulting your local gas supplier.
Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent using genuine
Garland replacement parts. Garland will have no obligation with respect to any product that has been improperly installed,
adjusted, operated or not maintained in accordance with national and local codes or installation instructions provided
with the product, or any product that has its serial number defaced, obliterated or removed, or which has been modified
or repaired using unauthorized parts or by unauthorized service agents. For a list of authorized service agents, please refer
to the Garland web site at http://www.garland-group.com. The information contained herein, (including design and parts
specifications), may be superseded and is subject to change without notice.
Continuous product improvement is a Garland policy, therefore design and specifications are subject to change without notice.
GARLAND COMMERCIAL INDUSTRIES
185 East South Street
Freeland, Pennsylvania 18224
Phone: (570) 636-1000
Fax: (570) 636-3903
4517957 Rev. 2 (06/05)
4517957 Rev. 2 (06/05)
INSTRUCTIONS FOR THE
RANGE,
MODEL STW286A
WARNING: ELECTRICAL GROUNDING INSTRUCTIONS
GARLAND COMMERCIAL RANGES,
LTD.
1177 Kamato Road, Mississauga, Ontario L4W 1X4
CANADA
Phone: 905-624-0260
Fax: 905-624-5669
WARNING:
IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE CAN
CAUSE PROPERTY DAMAGE, INJURY OR DEATH.
READ THE INSTALLATION, OPERATION AND
MAINTENANCE INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR SERVICING
THIS EQUIPMENT.
Enodis UK LTD.
Swallowfield Way, Hayes, Middlesex UB3 1DQ ENGLAND
Telephone: 081-561-0433
Fax: 081-848-0041
© 2005 Garland Commercial Industries, Inc.
Page 1

Advertisement

Table of Contents
loading

Related Manuals for Garland SRW286A

Summary of Contents for Garland SRW286A

  • Page 1 This information shall be obtained by consulting your local gas supplier. Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent using genuine Garland replacement parts. Garland will have no obligation with respect to any product that has been improperly installed,...
  • Page 2 Page 2 4517957 Rev. 2 (06/05)

  • Page 3: Table Of Contents

    TABLE OF CONTENTS DIMENSIONS ......4 Cleaning Burners ..... . 14 Griddle / Solid Hot Plate.

  • Page 4: Dimensions

    DIMENSIONS 10' POWER CORD 3/4" NPT REAR AT REAR [120V] GAS INLET GUARD 10 1/2" 1 1/2" [267mm] [38mm] 3 3/4" [95mm] 3 1/2" [83mm] 39 1/2" 28" [1003mm] [711mm] 5" [127mm] 12" 24" [305mm] [610mm] 36" [915mm] 45 1/2" [1156mm] 31 3/4"...

  • Page 5: Specifications

    It is in your own interests and that of safety to ensure must also be removed. that the law is complied with. Your Garland Dealer is 3. All ranges are shipped from the factory with casters well qualified to provide this service.

  • Page 6: Rating Plate

    A preset gas pressure regulator is supplied with will deliver sufficient pressure to operate the unit GARLAND Restaurant Series Equipment. It may properly. be necessary to adjust the regulator to deliver fuel at •...

  • Page 7: Clearances

    INSTALLATION continued • In Canada, the installation must comply with local Location codes, or in the absence of local codes, with the The range should be installed on a firm, smooth and Installation Codes for Gas Burning Appliances and level floor designed to withstand the weight of the fully Equipment CAN/CGA-B149.1 and CAN/CGA laden appliance.

  • Page 8: Gas Connection

    INSTALLATION continued Gas Connection: which is 3/4” NPT. An isolating valve is recommended to be close to the appliance to allow shut down during The gas pipe connection is made at the rear right hand an emergency or routine servicing. After installation, the side of the equipment.

  • Page 9: Commissioning

    INSTALLATION continued Commissioning: 3. With a flat screwdriver, turn the adjuster on the body of the tap clockwise to reduce the pressure or The whole of the gas installation, including the meter, anti-clockwise to increase pressure. Set the pressure should be inspected, purged and tested for leakage in to correspond with table D.

  • Page 10: Operation

    OPERATION Safety concerns OVEN/GRIDDLE TOP It is the responsibility of the supervisor or equivalent person to ensure that users of this equipment wear suitable protective clothing and draw attention to the fact that some parts will by necessity become very hot and will cause burns if touched accidentally.

  • Page 11: Lighting The Griddle

    OPERATION continued Lighting The Griddle The recommended pre-heat time is 30 minutes. This will thoroughly saturate the plate. Pots must have flat NOTE: Ensure that the gas and electrical supply to the bottoms for maximum contact with the hot surface. appliance are turned “ON”.

  • Page 12: Convection Oven

    OPERATION continued PREHEAT TIME – Allow at least 45 minutes after 4. Wait five minutes and repeat steps 1 and 2. If a turning the oven on from cold, with the thermostat at problem persists have the unit checked by a the desired temperature before loading the oven with competent technician.

  • Page 13: Exhaust Filter

    MAINTENANCE & CLEANING continued Use only stainless steel, wood or plastic tools to scrape 1. Using a traditional 2.5”-3” (64mm-76mm) scraper off heavy deposits of grease or oil. Do not use ordinary or spatula scrape the griddle surface (to remove food steel scrapers or knives as particles of iron my become particles and oil residues) towards the grease trough embedded and rust.

  • Page 14: Cleaning Burners

    MAINTENANCE & CLEANING continued 2. Do not allow metal utensils (Spatula, scraper, etc.) 6. Clean the burner with a stiff scrubbing brush and to nick and/or dent the surface of the griddle, The shake the burner well to ensure that ports are clear edges of these utensils are sharp and will create of any debris.

  • Page 15: Griddle

    MAINTENANCE & CLEANING continued 3. Check the temperature reading just when the TOP VIEW control cycles “OFF” as indicated by cycling pilot 12.0 24.0 lamp. If the temperature does not read within 15°F of the dial setting, recalibrate as follows: ref.

  • Page 16: Miscellaneous

    Injector fittings ( One required for each main burner & one required for each pilot) b. Regulator, (one per unit ) If any of the required parts are missing, contact your Garland dealer before attempting to carry out the conversion. Page 16 4517957 Rev. 2 (06/05)

  • Page 17: Fault Finding

    FAULT FINDING PROBLEM POSSIBLE CAUSES SOLUTION No power to oven. Check power supply. Defective Cook/Cool Down switch Replace switch. Cook/Cool Down switch set to “Cook” position. Light off. Motor not working. Faulty wiring. Check condition of all wires & connections Defective door switch.

  • Page 18: Replacement Of Parts

    REPLACEMENT OF PARTS WARNING: Turn off the gas supply to the appliance 2. Slide out the control drawer to access the switch. at the service cock and the electrical mains before 3. Disconnect the wires from the taps on the switch. commencing any servicing work.

  • Page 19: Front Cooling Fan

    REPLACEMENT OF PARTS continued 4. Break the pipe union connection at the inlet of the Ignition Control gas control and the 7/16” union connection located 1. Remove the fastener securing the control at the outlet of the control. compartment access panel. 5.

  • Page 20: Identification

    REPLACEMENT PARTS IDENTIFICATION 109A 23 21 SK3894 SHT. 1 OF 2 ITEM PART No DESCRIPTION STW286A 076050-87 1/4 Compression Union 076050-88 7/16 Compression Union 1005800 Door Spring 2206513 Oven Spark Ignition Pilot NAT 2206512 Oven Spark Ignition Pilot PRO Oven Pilot Orifice (Specify Gas) 4518183 Pilot Bracket, Oven 22701XX...
  • Page 21 REPLACEMENT PARTS IDENTIFICATION continued DESCRIPTION ITEM PART No STW286A M9-XX Oven Orifice Hood (Specify Gas) 2635100 Oven Orifice Support Bracket 2624900 Tube ¼ - Oven Pilot to ¼ Compression Union 2642800 Sensor Wire 2624800 Tube 7/16 – 7/16 Oven Orifice to Compression Union 4518182 Oven Burner 1390702...
  • Page 22 REPLACEMENT PARTS IDENTIFICATION continued DESCRIPTION ITEM PART No STW286A 1309022 Insulation - Oven Cavity Top Rear 2677600 LH Roll Out Shield Aupport 1472202 Insulation - Oven Cavity Rear Sides 2621199 Flue Riser Assy 3013900 Main Back 1472200 Insulation - Cavity Back 2620800 Main Bottom 2301300...
  • Page 23 REPLACEMENT PARTS IDENTIFICATION continued 165A 172 171 173 202 175 SK3894A SHT. 2 OF 2 4517957 Rev. 2 (06/05) Page 23...
  • Page 24 REPLACEMENT PARTS IDENTIFICATION continued DESCRIPTION ITEM PART No STW286A 1669101 Motor Pocket Insulation Board 3013301 Motor Mount Pocket 3013401 Motor Mount Plate G02952-01P Blower Wheel 2640700 Manifold Support Bracket 2640800 Manifold Support Clamp G01474-5 3/4” NPT Elbow G01738-14 Nipple 3/4” NPT X 2” (Domestic Model) G01518-1 Valve-Swing Type Shut Off Gas (Domestic Model) G01738-9...
  • Page 25 REPLACEMENT PARTS IDENTIFICATION continued DESCRIPTION ITEM PART No STW286A 4516887 Grease Sleeve 4517610 Thermostat - Oven 1014900 Cast Iron H-Burner 1028002 Air Shutter (Hot Top Burner) 2512100 Air Shutter (Griddle Burner) 4517190 Bulb Clamp/Shield Assy 2614500 Burner Box Bottom 4517373 Heat Shield-Tubing 2619400 Insulation Shield...
  • Page 26 REPLACEMENT PARTS IDENTIFICATION continued DESCRIPTION ITEM PART No STW286A 2198102 Valve Connector Fitting 10mm 2203400 1/8” NPT Plug G02251-1 Pressure Test Spigot G01243-1 Fitting 68-7B 1086597 Gum Valve – 3/16” Pilot 4517599 Tube (¼”) - Hot Top Valve to Hot Top Orifice Fitting 2625000 Tube (3/16”) - Hot Top Valve to Hot Top Pilot 2624700...
  • Page 27 REPLACEMENT PARTS IDENTIFICATION continued DESCRIPTION ITEM PART No STW286A 4516857 Control Panel 4517060 Overlay - Control Panel 2629000 Oven Control Cover 2628700 Oven Control Cover Support 2630200 Switch SPDT ON-OFF-ON 2146800 Illuminated Power Switch 2667200 Pilot Assy Amber 4517756* Extra 7/16” c.c. Hardware 4514749 Spark Generator - 230V, 4 outlet 4514750...

  • Page 28: Wiring Diagrams

    WIRING DIAGRAMS Page 28 4517957 Rev. 2 (06/05)
  • Page 29 WIRING DIAGRAMS 4517957 Rev. 2 (06/05) Page 29...
  • Page 30 WIRING DIAGRAMS Page 30 4517957 Rev. 2 (06/05)
  • Page 31 WIRING DIAGRAMS 4517957 Rev. 2 (06/05) Page 31...

Table of Contents