Black Horse Model Shark BH119 Instruction Manual Book
  1. Manuals
  2. Brands
  3. Black Horse Model Manuals
  4. Toy
  5. Shark BH119
  6. Instruction manual book
Black Horse Model Shark BH119 Instruction Manual Book

Black Horse Model Shark BH119 Instruction Manual Book

Hide thumbs
Table of Contents

Advertisement

Quick Links

SPECIFICATION
     Wingspan :
     Length
     Weight
     Radio
     Servo
     Engine
Electric Motor: RIMFIRE 1.20.
 Battery: 18.5 -22.2V(5-6S LIPO)
 
Propeller: 16x6

Speed control: 80A.
Instruction Manual book
1,800 mm
:
1,560 mm
:
4.8 kg
:
08 channels.
:
09 servos.
:
75
2 stroke.
20 CC Gas
70.87 in.
61.42 in.
10.56 Lbs.
Made in Vietnam.
Item code:BH119

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Shark BH119 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Black Horse Model Shark BH119

Summary of Contents for Black Horse Model Shark BH119

  • Page 1 Instruction Manual book Item code:BH119 SPECIFICATION      Wingspan : 1,800 mm 70.87 in.      Length 1,560 mm 61.42 in.      Weight 4.8 kg 10.56 Lbs.      Radio 08 channels.

  • Page 2: Parts List

    SHARK - Item code: BH119 . INSTRUCTION MANUAL This instruction manual is designed to help you build a great flying aeroplane. Please read this manual thoroughly before starting assembly of your SHARK. Use the parts listing below to identify all parts. WARNING.

  • Page 3: Safety Precaution

    SHARK - Item code: BH119 . INSTRUCTION MANUAL Caution: this model is not a toy! If you are a beginner to this type of powered model, please ask an experienced model flyer for help and support. If you attempt to operate the model without knowing what you are doing you could easily injure yourself or somebody else.
  • Page 4 SHARK - Item code: BH119 . INSTRUCTION MANUAL REPLACEMENT LARGE PARTS A. Cowling. E. Rudder B. Wing panel. F. Aluminium wing dihedral brace. C. Fuselage. G. Decal sheets. D . Horizontal stabilizer. REPLACEMENT SMALL PARTS...

  • Page 5: Installing The Aileron Servos

    SHARK - Item code: BH119 . INSTRUCTION MANUAL 1.Door mounting wheel. 2.Air retract main gear. 3. Wheels. 4. Air retract nose gear. Aileron 5.Valve control. 6.Valve one way. 7.3 way connectors. 8.4 way connector. 9. Spinner. 10. Air tank. 11.Air line sets. 12.Plastic parts for elevator and rudder pushrod.
  • Page 6 SHARK - Item code: BH119 . INSTRUCTION MANUAL Remove Electric wire Thread covering servo tray Electric wire 2x10mm. Secure. Secure Repeat the procedure for the other wing half.  3) Using the thread as a guide and using masking tape, tape the servo lead to the end INSTALLING THE AILERON CONTROL HORN.

  • Page 7: Installing The Aileron Linkages

    SHARK - Item code: BH119 . INSTRUCTION MANUAL INSTALLING THE AILERON LINKAGES. Installing the aileron linkages as pictures below. M2 lock nut 55mm A+B Epoxy PLUS glue Repeat the procedure for the other wing half. A+B Epoxy II. FLAP. PLUS glue 1.INSTALLING THE FLAP SERVOS.
  • Page 8 SHARK - Item code: BH119 . INSTRUCTION MANUAL 2x10mm. Flap control horn. Secure. 3. INSTALLING THE FLAP LINKAGES. Installing the flap linkages as pictures below. M2 lock nut 55 mm 2.INSTALLING THE FLAP CONTROL HORN. Flap control horn Bottom side Repeat the procedure for the other wing half.
  • Page 9 SHARK - Item code: BH119 . INSTRUCTION MANUAL 3x 15mm Secure. 5x30mm...
  • Page 10 SHARK - Item code: BH119 . INSTRUCTION MANUAL Drill a hole 3mm diameter Drill a hole 3mm diameter Secure 3x 6mm 3x 6 mm 3x 6mm...

  • Page 11: Option 1: Electric Motor

    SHARK - Item code: BH119 . INSTRUCTION MANUAL Secure. Remove wood Secure. Bottom side. Repeat the procedure for the other gear. THERE ARE TWO OPTIONS: 1. ELECTRIC MOTOR 2. ENGINE MOUNT. OPTION 1: ELECTRIC MOTOR INSTALLING ELECTRIC MOTOR. Push 3x 15mm...
  • Page 12 SHARK - Item code: BH119 . INSTRUCTION MANUAL Drill a hole 2mm diameter Front view. Drill hole 2mm. 3x 15mm 3x 15mm Secure. Secure. C/A glue. Battery...

  • Page 13: Option 2: Engine Mount

    SHARK - Item code: BH119 . INSTRUCTION MANUAL Drill a hole 6mm diameter. Front view. OPTION 2: ENGINE MOUNT. INSTALLING THE ENGINE MOUNT. See pictures below: 5x 70mm Secure. Rotor shaft...

  • Page 14: Installing The Throttle Cable

    SHARK - Item code: BH119 . INSTRUCTION MANUAL INSTALLING THE THROTTLE CABLE. Throttle servo. Throttle cable. Throttle servo. FUEL TANK. INSTALLING THE STOPPER ASSEMBLY  1. The stopper has been pre-assembled at the factory.  2. Using a modeling knife, cut one length of silicon fuel line (the length of silicon fuel line is Throttle servo.
  • Page 15 SHARK - Item code: BH119 . INSTRUCTION MANUAL When the stopper assembly is installed  8. Feed three lines through the fuel tank in the tank, the top of the vent tube should compartment and through the pre-drilled hole rest just below the top surface of the tank. in the firewall.
  • Page 16 SHARK - Item code: BH119 . INSTRUCTION MANUAL ELECTRIC COWLING. POWER  1. Slide the fiberglass cowl over the en- gine and line up the back edge of the cowl with the marks you made on the fuselage. Top side bottom side.
  • Page 17 SHARK - Item code: BH119 . INSTRUCTION MANUAL c e n t e r line 2 20mm center line 1...
  • Page 18 SHARK - Item code: BH119 . INSTRUCTION MANUAL trim and cut center line 3. trim and cut Bottom side. Right side Drill a hole 2mm c e n t e r diameter line 4...

  • Page 19: Installing The Spinner

    SHARK - Item code: BH119 . INSTRUCTION MANUAL INSTALLING THE SPINNER. Install the spinner backplate, propeller and spinner cone. The spinner cone is held in place using two 3mm x 12mm wood screws. 3 x 12mm Secure. Machine screw. Secure. Front view...
  • Page 20 SHARK - Item code: BH119 . INSTRUCTION MANUAL Secure Nose gear servo Botom side Air line set. INSTALLING AIR RETRACTABLE NOSE GEAR. 3x15mm. Secure. Nose gear servo...
  • Page 21 SHARK - Item code: BH119 . INSTRUCTION MANUAL 5x 30mm Secure...

  • Page 22: Vertical Stabilizer Installation

    SHARK - Item code: BH119 . INSTRUCTION MANUAL VERTICAL STABILIZER INSTALLATION. Rudder servo install as same as method of elevator servo. See picture below: C/A glue. C/A glue.  When you are sure that everything is a aligned correctly, mix up a generous amount of 30 minute epoxy.

  • Page 23: Rudder Pushrod Installation

    SHARK - Item code: BH119 . INSTRUCTION MANUAL Botom side A+B Epoxy PLUS glue Rudder pushrod RUDDER PUSHROD INSTALLATION.  1. Rudder pushrod install as same as the way of aileron control horn.  2. Rudder push - pull system install as same as picture below.

  • Page 24: Horizontal Stabilizer Installation

    SHARK - Item code: BH119 . INSTRUCTION MANUAL Elevator servo C/A glue. HORIZONTAL STABILIZER INSTALLATION. C/A glue. Horizontal stabilizer installation .  See picture below. Bottom side C/A glue. C/A glue. C/A glue. C/A glue. C/A glue.
  • Page 25 SHARK - Item code: BH119 . INSTRUCTION MANUAL Epoxy glue C/A glue. Top side C/A glue. R e m o v e covering Bottom side.

  • Page 26: Elevator Control Horn Installa- Tion

    SHARK - Item code: BH119 . INSTRUCTION MANUAL ELEVATOR CONTROL HORN INSTALLA- TION. Elevator control horn install as same as the way of aileron control horn. Please see pic- tures below. E p o x y PLUS Glue. Elevator pushrod Plastic parts of elevator and rudder pushrod.
  • Page 27 SHARK - Item code: BH119 . INSTRUCTION MANUAL C/A glue Elevator servo INSTALLING SERVO USING FOR VALVE CONTROL C/A glue Botom side rudder servo Valve control Elevator servo...
  • Page 28 SHARK - Item code: BH119 . INSTRUCTION MANUAL...

  • Page 29: Instruction Manual

    SHARK - Item code: BH119 . INSTRUCTION MANUAL 3 way Valve one way conector 4 w a y conector 3 way conector Air tank Air supply Valve one way Nose gear 4 way conector 4 way conector Left main gear wing Right main gear wing Valve control...

  • Page 30: Installing The Switch

    SHARK - Item code: BH119 . INSTRUCTION MANUAL switch of Receiver switch of engine INSTALLING THE RECEIVER AND BATTERY.       1. Plug the servo leads and the switch lead into the receiver. You may want to plug an aileron extension into the receiver to make plugging in the aileron servo lead easier when you are installing the wing .

  • Page 31: Wing Attachment

    SHARK - Item code: BH119 . INSTRUCTION MANUAL *** Test fit the aluminium tube dihedral brace into each wing haft. The brace should slide in easily. If not, use 220 grit sand around the edges and ends of the brace until it fits prop- battery erly.
  • Page 32 SHARK - Item code: BH119 . INSTRUCTION MANUAL See picture wing attach to fuselage. Top side. Installing the fuselage hatch as same as pic- ture below. Wing bolt. 6 x 75mm BALANCING. Wing bolt.       1) It is critical that your airplane be bal- anced correctly.

  • Page 33: Pre-Flight Check

    SHARK - Item code: BH119 . INSTRUCTION MANUAL PRE-FLIGHT CHECK.       1) Completely charge your transmitter and receiver batteries before your first day of fly- ing.       2) Check every bolt and every glue joint in your plane to ensure that everything is tight and well bonded.

Table of Contents