User's guide - ibm pc300 (6344) (swedish) (194 pages)
Summary of Contents for IBM 2193
Page 1
Hardware Maintenance Service for Service Level A For Micro Tower Models Machine Type 2193, 2194 and 6345 For Desktop Models Machine Type 2196, 2197 and 6344...
Page 2
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. References to IBM products, programs, or services do not imply that IBM intends to make them available outside the United States. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein;...
Mouse................ 93 Power Supply............. 96 Monitor............... 99 Undetermined Problems ..........101 Diagnostic Aids .............. 103 Introduction ..............104 Power-On Self Test............104 Diagnostics Tools............. 105 Using Diagnostics Program from Recovery CD..105 Diagnostics Program Features........106 Copyright IBM Corp. 2000...
Page 4
(US/Canada/LA)............144 Connectors and Functions of System Board of the Machine Type 6344 (US/Canada/LA) ........145 Layout of System Board of the Machine Type 2193 and 2196................. 146 Jumper Settings of the System Board of the Machine Type 2193 and 2196 ..........147 Connectors and Functions of System Board of the Machine Type 2193 and 2196........
Page 5
Safety Inspection Guide ..........169 General Guidelines ............170 Parts Catalog..............171 Part Catalog of machine type 2193, 2194, and 6345 ..172 Assembly 1: System Unit ..........172 Assembly 2: Diskette Drive, Hard Disk Drive ....176 Assembly 3: CD-ROM, Modem Card......177 Assembly 4: Keyboard and Mouse ......
References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only IBM’s product, program, or service may be used.
Safety Information DANGER To avoid a shock hazard, do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. To avoid shock hazard: The power cord must be connected to a properly wired and earthed receptacle.
Page 8
To Connect To Disconnect 1. Turn Everything OFF. 1. Turn Everything OFF. 2. First, attach all cables to 2. First, remove power devices. cord(s) from outlet 3. Attach signal cables to 3. Remove signal cables receptacles. from receptacles. 4. Attach power cord(s) to 4.
Page 9
Caution: When replacing the battery, use only IBM Part Number 36L9077 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.
Page 10
DANGER Some CD-ROM drives contain an embedded Class 3A or Class 3B laser diode. Note the following. Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. ≥...
Page 11
PERIGO Para evitar choques elétricos, não conecte ou desconecte nenhum cabo, nem efetue instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. Para evitar choques elétricos: O cabo de alimentação deve ser conectado a um receptáculo corretamente instalado e aterrado. Todos os equipamentos aos quais este produto será...
Page 12
Para Conectar Para Desconectar 1. DESLIGUE tudo. 1. DESLIGUE tudo. 2. Conecte primeiro todos os 2. Remova primeiro o(s) cabos nos dispositivos. cabo(s) de alimentação das tomadas. 3. Conecte os cabos de sinal nos receptáculos. 3. Remova os cabos de sinal dos receptáculos.
Page 13
Ao substituir a bateria, utilize apenas o Número de Peça IBM 33F8354 ou um tipo de bateria equivalente recomendado pelo fabricante. Se seu sistema possuir um módulo com uma bateria de lítio, substitua-o apenas pelo mesmo tipo de módulo, produzido pelo mesmo fabricante.
Page 14
PERIGO Algumas unidades de CD-ROM contém um diodo de laser da Classe 3A ou da Classe 3B. Observe o seguinte. Radiação de laser quando aberto. Não olhe diretamente para o feixe de laser, não olhe diretamente com instrumentos óticos, e evite exposição direta ao raio. ≥...
Page 20
DANGER Pour éviter tout risque de choc électrique, ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration de ce produit au cours d'un orage. Pour éviter tout risque de choc électrique : Les cordons d'alimentation du présent produit et de tous les appareils qui lui sont connectés doivent être branchés sur des socles de prise de courant correctement câblés et mis à...
Page 21
Remplacez la pile usagée par une pile de référence identique exclusivement - voir la référence IBM - ou par une pile équivalente recommandée par le fabricant. Si votre système est doté d'un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant.
Page 22
DANGER Certaines unités de CD-ROM contiennent une diode laser de classe 3A ou 3B. Prenez connaissance des informations suivantes : Rayonnement laser lorsque le carter est ouvert. Évitez de regarder fixement le faisceau ou de l'observer à l'aide d'instruments optiques. Évitez une exposition directe au rayon.
Page 23
Le courant électrique circulant dans les câbles de communication et les cordons téléphoniques et d'alimentation peut être dangereux. Pour votre sécurité et celle de l'équipement, avant de retirer les carters, mettez celui-ci hors tension et déconnectez ses cordons d'alimentation, ainsi que les câbles qui le relient aux réseaux, aux systèmes de télécommunication et aux modems (sauf instruction contraire mentionnée dans les procédures d'installation et de configuration).
Page 24
5. Gerät einschalten. achtung: Eine verbrauchte Batterie nur durch eine Batterie mit der IBM Teilenummer 33F8354 oder durch eine vom Hersteller empfohlene Batterie ersetzen. Wenn Ihr System ein Modul mit einer Lithium-Batterie enthält, ersetzen Sie es immer mit dem selben Modultyp vom selben Hersteller. Die Batterie enthält Lithium und kann bei unsachgemäßer...
Page 25
achtung: Wenn ein CD-ROM-Laufwerk installiert ist, beachten Sie folgendes. Steuer- und Einstellelemente sowie Verfahren nur entsprechend den Anweisungen im vorliegenden Handbuch einsetzen. Andernfalls kann gefährliche Laserstrahlung auftreten. Das Entfernen der Abdeckungen des CD-ROM-Laufwerks kann zu gefährlicher Laserstrahlung führen. Es befinden sich keine Teile innerhalb des CD-ROM-Laufwerks, die vom Benutzer gewartet werden müssen.
Page 26
VORSICHT Manche CD-ROM-Laufwerke enthalten eine eingebaute Laserdiode der Klasse 3A oder 3B. Die nachfolgend aufgeführten Punkte beachten. Laserstrahlung bei geöffneter Tür. Niemals direkt in den Laserstrahl sehen, nicht direkt mit optischen Instrumenten betrachten und den Strahlungsbereich meiden. ≥ ≥ ≥ ≥ 32 Kg ≥...
Page 27
PERICOLO Per evitare il pericolo di scosse elettriche durante i temporali, non collegare o scollegare cavi, non effettuare l'installazione, la manutenzione o la riconfigurazione di questo prodotto. Per evitare il pericolo di scosse elettriche: collegare il cavo di alimentazione ad una presa elettrica correttamente cablata e munita di terra di sicurezza;...
Page 28
ATTENZIONE: Quando si sostituisce la batteria, utilizzare solo una batteria IBM o batterie dello stesso tipo o di tipo equivalente consigliate dal produttore. Se il sistema di cui si dispone è provvisto di un modulo contenente una batteria al litio, sostituire tale batteria solo con un tipo di modulo uguale a quello fornito dal produttore.
Page 29
PERICOLO Alcune unità CD-ROM contengono all'interno un diodo laser di Classe 3A o Classe 3B. Prestare attenzione a quanto segue: Aprendo l'unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici ed evitare l'esposizione diretta al fascio. ≥...
Page 33
PELIGRO Para evitar una posible descarga eléctrica, no conecte ni desconecte los cables ni lleve a cabo ninguna operación de instalación, de mantenimiento o de reconfiguración de este producto durante una tormenta eléctrica. Para evitar una posible descarga: El cable de alimentación debe conectarse a un receptáculo con una instalación eléctrica correcta y con toma de tierra.
Page 34
Al cambiar la batería, utilice únicamente la batería IBM Número de pieza 33F8354 o un tipo de batería equivalente recomendado por el fabricante. Si el sistema tiene un módulo que contiene una batería de litio, sustitúyalo únicamente por el mismo tipo de módulo del mismo fabricante.
Page 35
PELIGRO Algunas unidades de CD-ROM tienen incorporado un diodo de láser de Clase 3A o de Clase 3B Tenga en cuenta la siguiente información. Cuando la unidad está abierta se generan emisiones de rayos láser. No dirija la mirada al haz, no lo observe directamente con instrumentos ópticos y evite la exposición directa.
Laser Compliance Statement The CD/DVD-ROM drive in the computer is a laser product. The CD/DVD-ROM drive's classification label (sample shown below) is located on the drive. CLASS 1 LASER PRODUCT APPAREIL A LASER CLASSE 1 LASER KLASSE 1 LUOKAN 1 LASERLAITE PRODUIT LASER CATEGORIE 1 The CD/DVD-ROM drive is certified in the U.S.
Trademarks The following are trademarks of the IBM Corporation in the United States or other countries or both: Operating System/2 OS/2 Personal System/2 HelpCenter PS/1 PS/2 Intel, Pentium, MMX, EtherExpress, and LANDesk are trademarks or registered trademarks of Intel Corporation.
A (SL-A) model of the IBM Personal Computer, worldwide. This manual is intended to be used as a stand-alone document to service Machine type 2193, 2194, 2196, 2197, 6344 and 6345 product. It is divided into the following chapters: Notices contains important safety information and notices required to service this computer.
BIOS Setup Utility ............48 Working with the Setup Menus........48 Start Options.............. 50 Advanced Setup ............52 Power Management Setup......... 56 ISA Legacy Resource ..........58 Set Password............. 58 Specifications..............59 Operating Requirements ..........60 Special Tools ..............61 Copyright IBM Corp. 2000...
2193, 2194, 2196, 2197, 6344 and 6345, describes the standard and optional features, and details functional and environmental specifications. The machine type 2196, 2197 and 6344 are desktop models. The machine type 2193, 2194 and 6345 are micro tower models. Product Overview...
Page 42
Hard Disk Drive • 3.5-in., 1-in. height IDE AT drive. • 512 KB cache buffer in hard disk drive. • Average and minimum 11.1 ms seek time, access time varies for the hard disk drive and the hard disk drive manufacturer.
Page 43
• Auto-sensing power input for 100 V ac to 240 V ac. Keyboard • PS/2 104-key rubber dome IBM Keyboard with 1.8-m (5.8-ft) cable. Keyboard is Geography/Model dependent. Mouse • 2 button mouse connected to the mouse port with 1.8-m...
Photo-CD (both single and multi- session) format. Diskette Drive AT diskette interface Video Physical interface is compatible with the IBM Personal System/2 (PS/2) VGA interface. SiS540, SIS 630 and Intel 810e VGA on board. Modem One 56.6 Kbps PCI plug and play modem adapter card with data/fax features.(not standard in 6344 and...
Page 45
EPP (IEEE 1284 compliance), ECP (IEEE 1284 compliance) interface. Game port Game port interface for joystick. It also supports MIDI. Ethernet Port Only 2194 and some 2193 models do not have Ethernet on board USB controller integrated in core logic chip set.
CMOS Reset This system does not deny access to BIOS Setup Utility. Execute “Load BIOS Default Settings” in BIOS Setup to clear the corrupted CMOS data. See “Loading the Default Settings” on page 49.
Flash (BIOS) Update Procedure NOTE: The flash update procedure does not change the model number and serial number information in BIOS. 1. Prepare a bootable DOS diskette with AWDFLASH.EXE and VXXYYZZ.BIN files NOTE: The AWDFLASH.EXE is flash utility programs. The VXXYYZZ.BIN is a BIOS source code binary file.
BIOS-contained Model Number and Serial Number The model number and serial number information is stored in BIOS ROM and displayed in the “Model Information” of BIOS Setup main menu. If a repair is completed by replacing the system board or installing a new BIOS ROM, then you need to enter the original system model number and serial number in the new BIOS ROM.
Follow these steps to enter Setup when the computer is off: 1. Turn on your monitor. 2. Turn on the system unit. 3. When you see the IBM logo, press F1 to enter Setup and display the Main Menu. Refer to the Setup Utility Main Menu below.
Page 50
Loading the Default Settings (Setup Defaults) When you purchase an IBM personal computer, it is already configured for use. The original configuration settings, also called factory or default settings, are stored in the CMOS. Setup includes an option Load Optimized Default Settings that allows you to reload the original configuration at any time.
You must load the Setup default settings in the following instances: − When you replace the system battery − When you customize your system configuration settings and some resource assignments conflict causing the computer to hang. Exiting Setup (Save & Exit Setup/Exit Without Saving) Press Esc to return to the main menu when you have finished viewing settings and making changes.
Page 52
Virus Warning Determines if the BIOS will monitor the boot sector and partition table of the hard disk drive for any attempt at modification. If any attempt is made, the BIOS will halt the system and an error message will appear. Afterwards, if necessary, you will be able to run an anti-virus program to locate and remove the problem before any damage is done.
Typematic Delay (Msec) When the typematic rate is enabled, you can select the delay between when the key was first depressed and when the acceleration begins. Security Option Determines the access limitation to the system and Setup, or just Setup. Report No Diskette Drive for Win 95 Select YES to release IRQ6 (Interrupt Request) when the system contains no floppy drive for compatibility with Windows...
Page 54
ROM Shadowing Video BIOS Shadowing option determines whether video BIOS will be copied to RAM. However, it is optional depending on chipset design. Video Shadow will increase the video speed. C8000- DFFF Shadowing option determines if the option ROMs will be copied to RAM. Devices and I/O ports The options in this menu item are used to configure the devices and the I/O ports that this system has.
Page 55
USB Setup The options in this menu item are used to enable the USB (Universal Serial Bus) functions. USB Controller Select enabled if you will use USB device. USB Keyboard Support Select enabled to use a USB keyboard. Also the USB Controller must be set to enabled.
Page 56
Ultra DMA (Direct Memory Access) This setting allows you to speed up data transfer between the IDE devices and your system. Select the Auto option to enable it or select disabled to disable it. IDE Brust Mode Determines the acceleration of data transfer for IDE devices. IDE Data Port Post write Determines the data transfer in the manner of “post write”...
Onboard FDD Control Allows you to enable or disable the diskette drive (floppy disk drive) controller. Game Port Address Determines the game port I/O address. Midi Port Address Determines the game port I/O address. Midi Port Address Determines the midi port IRQ (Interrupt Request) number. Power Management Setup The Power Management Setup allows you to configure your system to most effectively save energy while operating in a...
Page 58
Activity Monitor MODEM Use IRQ Allows you to select the IRQ to be used by the modem. HDD Port Activity When set to enabled, any activity taking place at the hard disk or diskette drive will awaken the computer from a powered- down/stndby state.
ISA Legacy Resource ISA legacy resources (DMA, Interrupts, Memory) are resources that used by ISA adapters which are not Plug-and-Play adapters. Don’t use this setting due to the computer only support pci adapter cards. CLOCK Generator Configation This setting allows you to change the clock rate of CPU, SDRAM, DIMM and PCI bus.
Specifications Dimensions (width x depth x height): • System unit: For machine type 2193, 2194 and 6345: − 190 mm (7.48 in.) x 370 mm (14.57 in.) x 380 mm (14.96 in.) For machine type 2196, 2197 and 6344: −...
Operating Requirements All machines require two power inputs: one on the system unit and one on the monitor display. The system unit comes with a voltage selector switch, allowing selection of either 115 V ac or 230 V ac. This switch must be in the 230 V ac position when the machine is plugged into a 230 V ac electrical outlet.
Special Tools The following special tool is required to service this system when running the diagnostics program (PC-Doctor): • Wrap plug, P/N 72X854...
Introduction This chapter contains the check procedures used to diagnose the causes of product failures. The diagnostic information consists of: Start: This is the starting point for any diagnostic action. Based on high-level symptoms, the check procedure directs you to more detailed procedures to help resolve machine failures. Index of Symptoms, Messages, Error Codes, or Beeps: The tables for BIOS Error Messages, Codes, Beeps, and Error Symptoms list symptoms along with their probable causes, and...
Page 65
POST error codes and error messages are displayed on the screen after the IBM logo. A beep will precede each error code or message. Please refer to “Index of Symptoms, Messages, Error Codes, or Beeps” on page 69 for additional help.
Power off the system unit before moving it or when replacing FRUs. Remove all adapter cards, except for the factory-installed modem adapter card and any other IBM factory-installed adapter cards. Disconnect any drives except: 3.5-in. diskette drive...
Page 67
Note any symptoms, messages, error codes, or beeps. Make sure that there are no diskettes or CDs in the drives. 002 - DOES AN IBM LOGO SCREEN APPEAR? (YES, READ AHEAD. NO, GO TO STEP 004.) Insert the diagnostics diskette in the diskette drive.
Page 68
005 - If the keyboard responds incorrectly, go to "Keyboard" on page 92. 006 - DOES THE SYSTEM CONFIGURATION REPORT CORRECTLY IDENTIFY THE DEVICES INSTALLED IN SYSTEM? (YES, READ AHEAD. NO, GO TO STEP 007.) Select Diagnostics from the diagnostics program menu. Select and execute All Tests.
Page 69
008 - DOES THE DIAGNOSTICS FINISH WITHOUT ANY ERRORS? (YES, READ AHEAD. NO, GO TO STEP 009.) If the Diagnostics \ All Tests did not detect a failure but the system still indicates a failure: Check all adapter card jumper settings. Check all adapter cards switch settings.
Index of Symptoms, Messages, Error Codes, or Beeps How to Use Error Messages: Use the messages, error codes, and beeps combinations that occur to diagnose failures. If more than one failure occurs, diagnose from the first failure that appears. The cause of the first failure can result in false messages, error codes, or beeps.
Page 71
NOTES: If an error message and incorrect audio response occur, diagnose the error message first. If you cannot run the diagnostics program tests but did receive a POST error code, diagnose the POST error message. If you did not receive any error message, look for a description of your error symptoms in “Error Symptoms List”...
Page 72
Table 2-1 BIOS Error Codes, Messages, and Beeps List Action/FRU BIOS Error Codes, Messages, beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
Page 73
Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
Page 74
Table 2-1 BIOS Error Codes, Messages, and Beeps List Action/FRU BIOS Error Codes, Messages, beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
Page 75
Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
Page 76
Table 2-2 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
Page 77
Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 78
Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 79
Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 80
Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 81
Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 82
Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 83
Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 84
Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Troubleshooting Failing Parts or Assemblies: The check procedures generally help you trace a problem to one part or assembly. The last step of the specific check procedure you are using indicates that a part or assembly is failing. You should inspect the part or assembly before you decide to replace it.
Factory-Installed Storage Devices Use this check procedure to test any factory-installed drives. ATTENTION: The customer may have customized settings in the Setup Utility (other than default settings) on the computer you are servicing. Running the Setup Utility might alter those settings. Take note of the current settings and verify that the customer settings are in place when service is complete.
Page 87
IDE Primary Channel Master and Slave Drives in BIOS Setup should be connected to the system board primary IDE connector. (Please refer to the connectors and functions illustrated in chapter 5.) IDE Secondary Channel Master and Slave Drives in BIOS Setup should be connected to the system board secondary IDE connector.
Factory-Installed Modem Card 001 - START Power off the system unit. In Windows 98 Device Manager, make sure that the modem is not configured with a conflicting COM port and IRQ setting. Make sure that the communication software is configured with the correct COM and IRQ settings (same as COM port and IRQ as the modem).
Page 89
004 - CAN THE MODEM DIAL OUT AND CONNECT TO ANY BBS SUCCESSFULLY? (YES, READ AHEAD. NO, GO TO STEP 005.) The modem adapter functions normally. End. 005 - Make sure that Windows 98 is properly installed, then power off the system unit. Plug the modem adapter card into a different PCI slot.
Audio (Not Supported by Diagnostics Program) NOTE: Audio tests for the sound card cannot be carried out in the PC Doctor DOS diagnostics program. It is, however, possible to carry out a dial tone test for the modem. While performing this check, you may need to enter and exit Microsoft Windows 98 several times.
004 - Perform the following under Windows 98. NOTE: If an operating system other than Microsoft Windows 98 is installed, the program screens and icons may differ from these instructions. 1. Start Microsoft Windows 98. 2. Select the Start icon. 3.
Page 92
Insert the diagnostics diskette into the diskette drive and make sure that there is no CD in the CD-ROM drive. Select Interactive Tests menu, then select and execute CD-ROM Test. 002 - DO YOU SEE A MESSAGE “NO CD-ROM DRIVE OR MSCDEX DEVICE DRIVER INSTALLED.”...
Memory 001 - START Power off the system unit. Insert the diagnostics diskette into the diskette drive. Make sure that all DIMMs are installed correctly. Power on the system unit. Take note of any messages, error codes, or symptoms. 002 - DO YOU RECEIVE POST MEMORY ERROR MESSAGE? (YES, READ AHEAD.
Insert the diagnostics diskette into the diskette drive and power on the system unit. Select Interactive Tests menu, then execute Keyboard test. 003 - DOES THE KEYBOARD FUNCTION CORRECTLY? (YES, READ AHEAD. NO, GO TO STEP 004.) Keyboard is functioning normally. End.
Page 95
Insert the diagnostics diskette into the diskette drive. Power on the system unit. Select Interactive Tests menu, then execute Mouse test. 003 - DO YOU SEE THE MOUSE CURSOR IN THE DIAGNOSTICS PROGRAM? (YES, READ AHEAD. NO, GO TO STEP 011) Test right (left) button and check if right (left) button works.
Power Supply 001 - START Power off the system unit. Check the power cord for continuity. Replace if necessary. Check for the correct line voltage from the power outlet, and verify that the voltage selector switch is set to the correct voltage.
Page 97
Power Supply Connectors (Bottom View) Hard Drive or CD-ROM End of Power Cable 3.5-In. Diskette Drive End of Power Cable...
Page 98
006 - ARE THE VOLTAGES CORRECT AND DOES THE FAN RUN? (YES, READ AHEAD. NO, GO TO STEP 009) The power supply is working normally. If you suspect the on/off switch cable assembly, see Step 003. If the fan continues to run when all connectors are plugged back in, go to “Undetermined Problems”...
Monitor First, set the system to VGA mode. To do this in Windows 98, press the F8 function key during startup. Safe mode (VGA) will be set for Windows 98. Use the operating system's video setup to change the monitor resolution. If the monitor type is set to the power saving mode, the screen remains black and the LED lights or flashes in amber color.
Page 100
002 - IS THE SCREEN READABLE? (YES, READ AHEAD. NO, GO TO STEP 004) NOTE: If the screen shows a blinking cursor with no memory count running, answer this question "No". Select Interactive Tests from the Main Menu. Select and execute Video test from the menu. Follow the prompts and perform the video test.
Check all cables and connectors for proper installation. If the jumpers, switch, and voltage settings are correct, return here and continue: 3. Remove or disconnect the following, one at a time: Non-IBM devices External devices Any adapters Modem card, if installed...
Diagnostic Aids Diagnostic Aids .............. 103 Introduction ..............104 Power-On Self Test............104 Diagnostics Tools............. 105 Using Diagnostics Program from Recovery CD..105 Diagnostics Program Features........106 Copyright IBM Corp. 2000...
BIOS version and system memory tested. 3. If an error is detected during POST, the IBM logo screen will automatically switch to the text-based screen and display the error message or code with a beep. Depending on the criticality of the POST error, the system may halt and/or display the message “Press F1 to go to the Setup or...
This version of PC-Doctor diagnostics program, developed by Watergate for IBM, is the primary method of testing the computer. You can use it to test the IBM components of the system and some external devices. The amount of time required to test components depends on the number of components installed and selected.
Diagnostics Program Features Diagnostics program (PC-Doctor for DOS) includes the following features: Table 3-1. Diagnostics Program Features Main Menu Selections Submenu Selections • System Test Diagnostics • Memory Test • Hard Disk Test • Floppy Disk Test • All Tests •...
Page 107
• Onboard Ethernet Hardware Info • USB Port • System Configuration • Memory Contents • IRQ and DMA Use • Device Drivers • COM and LPT Ports • Physical Disk Drives • Logical Disk Drives • VGA Information • Software Interrupts •...
Page 109
Repair Information Repairing Information ............ 109 Removals and Replacements of machine type 2193, 2194, and 6345 ..............110 Identifying the Parts of the System Unit......111 Top Cover ................ 113 Adapter Cards............114 Diskette Drive ............116 CD-ROM Drive............118 Hard Disk Drive............
Removals and Replacements of machine type 2193, 2194, and 6345 BEFORE REMOVING ANY FRU, POWER-OFF THE COMPUTER UNPLUG ALL POWER CORDS FROM ELECTRICAL OUTLETS, THEN DISCONNECT ANY INTERCONNECTING CABLES. ATTENTION: The System board, processors, adapter cards, DIMMs, and upgrade processors can be damaged by electrostatic discharge.
This system has 3 interface cards slots for adapter card expansion. All of them are Peripheral Component Interconnect (PCI) interfaces. Only 2194 and some 2193 models do not have a 10/100 Mbps Ethernet port on board. 2193 system can support DFP (Digital Flat Panel) function.
Page 112
1. Power Supply This is a 95-watt switching power supply. 2. CD-ROM Drive This machine has a factory-installed 40 X CDROM drive. 3. Bay 2 This drive can accommodate a 5.25-inch device. 4. Hard Disk Drive This machine has a factory-installed 3.5” (10 or 15) GB hard disk drive.
Top Cover To remove the top cover of this system unit: Remove the 4 screws that secure the top cover at the back of the system unit. Hold both sides of the system unit cover and push it backward about 25 mm. Lift the top cover up to remove it completely.
Adapter Cards Installing Adapter Cards Remove the screw that secures the adapter card retainer and slot cover. Then remove the card retainer and slot cover. Align and insert the adapter card into the adapter card connector. Secure the card with the screw that you removed in the first step.
Page 115
Removing Adapter Cards Follow these steps to remove an adapter card: Position the system unit so that the card is accessible to you. If the adapter card has cables, disconnect them. Be sure to take note of where the cable is connected. You will have to reconnect these cables when you reinstall the card.
Diskette Drive To remove the diskette drive: Disconnect the power and signal cables from the back of the diskette drive. Remove the diskette mounting tray from the chassis as following illustration : Pivot the latch that secures the lower drive-mounting tray. Slide the drive-mounting tray toward the rear of the computer and remove it.
Page 117
Remove the four screws (two on each side) that hold the diskette drive to the mounting tray .Pull the diskette drive from the mounting tray to remove it.
CD-ROM Drive To remove CD-ROM Drive: Disconnect the power, sound and signal cables from the CD-ROM. Remove the four screws (two on each side) that hold the CD-ROM drive to the chassis. Open the door on the front of the computer. Slide the CD-ROM drive forward through the front opening and remove it.
Hard Disk Drive To remove or replace the hard disk drive: Make sure to disconnect the power and signal cables from the CD-ROM drive and the diskette drive. Pivot the latch that secures the lower drive-mounting tray. Slide the drive-mounting tray toward the rear of the computer and remove it.
Remove the four screws (two on each side) that hold the hard disk drive to the mounting tray. Pull the hard disk drive from the mounting tray to remove it. System Board To remove the system board from the system: To remove the system board.
Layout of system board of the machine type 2193 1.DIMM 11. PCI SLOT 1 2.Power Switch connector 12. PCI SLOT 2 3.CPU Fan Connector 13. PCI SLOT 3 4.Hard Disk Drive Led and 14. USB Power Led 5.Primary IDE Connector 15.
Page 122
Layout of system board of the machine type 2194 and 6345 1. DIMM 11. PCI SLOT 2 2. Power Switch connector 12. PCI SLOT 3 3. CPU Fan Connector 13. USB 4. Hard Disk Drive LED and 14. CD-ROM audio signal Power LED connector 5.
Power Supply This system has a 95-watt switching power supply. 1. To remove the power supply. You must remove the top cover first. 2. Disconnect the power cable from the riser board and all drives. 3. Remove the screws in the machine rear that secure the power supply.
Removals and Replacements of machine type 2196, 2197, and 6344 BEFORE REMOVING ANY FRU, POWER-OFF THE COMPUTER UNPLUG ALL POWER CORDS FROM ELECTRICAL OUTLETS, THEN DISCONNECT ANY INTERCONNECTING CABLES. ATTENTION: The System board, processors, adapter cards, DIMMs, and upgrade processors can be damaged by electrostatic discharge.
Identifying the Parts of the System Unit This computer system has 3 bays, each bay has a factory- installed drive in it. The devices are 3.5” Diskette, 40X CD- ROM drive and 5.0 GB hard disk (some models may have hard disk of 10 or 15 GB capacity).
Page 126
1. Power Supply This is a 95-watt switching power supply. 2. Expansion slots On the rear panel of the system unit are 3 slot openings for installation of adapter card. 3. Modem card This system may include a V.90 Data/Fax modem. For 6344 systems will use the Ethernet card.
Top Cover To remove the top cover of this system unit: Remove the screws that secure the top cover at the back of the system unit. Hold both sides of the system unit top cover and push it forward about 25 inch. Lift the top cover up to remove it completely.
Adapter Cards Installing Adapter Cards Remove the screw that secures the adapter card retainer and slot cover. Then remove the card retainer and slot cover. Align and insert the adapter card into the adapter card connector. Secure the card with the screw that you removed in the first step.
Page 129
Removing Adapter Cards Follow these steps to remove an adapter card: Position the system unit so that the card is accessible to you. If the adapter card has cables, disconnect them. Be sure to take note of where the cable is connected. You will have to reconnect these cables when you reinstall the card.
Diskette Drive To remove the diskette drive: Disconnect the power and signal cables from the back of the diskette drive. Pull up the latch that secures the drive-mounting tray. Slide the drive-mounting tray toward from the front of the computer and remove it. Remove the four screws (two on each side) that secure the bay holder.
CD-ROM Drive To remove CD-ROM Drive: Disconnect the power, sound and signal cables from the CD-ROM. Pull up the latch that secures the CD-ROM drive-mounting tray. Slide the drive-mounting tray toward the back of the computer and remove it. Remove four screws (two on each side) that secure the bay holder.
Hard Disk Drive To remove or replace the hard disk drive: Follow the above steps to remove the CD-ROM. Make sure to disconnect the power cord and signal cables from the hard disk drive and the diskette device. Remove the screws that secure the bay holder that holds the hard diskette drive.
System Board To remove the system board from the system: To remove the system board. You must remove the adapter cards first. Disconnect the power cable, CD-ROM cable, Diskette Drive cable, Hard Disk Drive cable, audio cable, power switch cable, speaker cable and LED cable from system board.
Page 134
Layout of system board of machine type 2196 1. DIMM 11. PCI SLOT 1 2. Power Switch connector 12. PCI SLOT 2 3. CPU Fan Connector 13. PCI SLOT 3 4. Hard Disk Drive LED and 14. USB Power LED 5.
Page 135
Layout of system board with SiS630 core logic chip set (machine type 2197 and 6344) 1. DIMM 11. PCI SLOT 1 2. Power Switch connector 12. PCI SLOT 2 3. CPU Fan Connector 13. PCI SLOT 3 4. Hard Disk Drive LED and 14.
Power Supply This system has a 95-watt switching power supply. 1. To remove the power supply. You must remove the top cover first. 2. Disconnect the power cable from the riser board and all drives. 3. Remove the screws in the machine rear that secure the power supply.
Memory (DIMM) This system has 2 system memory module sockets, DIMM 0 and DIMM 1. These sockets hold dual in line memory modules (DIMM) that contains 3.3V signal or double-sided synchronous DRAM (SDRAM). The maximum memory size is 512 MB total.
(US/Canada/LA)............144 Connectors and Functions of System Board of the Machine Type 6344 (US/Canada/LA) ........146 Layout of System Board of the Machine Type 2193 and 2196................. 146 Jumper Settings of the System Board of the Machine Type 2193 and 2196 ..........147 Connectors and Functions of System Board of the Machine Type 2193 and 2196........
Introduction This chapter contains system board layouts and jumper settings. It is useful when you are asked to measure voltages. Use this information to help you locate parts such as electronic boards, connectors, pin numbers, and test points. This chapter also contains jumper settings for the hard disk drive, CD-ROM (compact disc-read-only memory) drive, and the connector information for modem adapter card.
Layout of System Board of the Machine Type 2194 (Italy), 2197 and 6344 (EMEA/AP) Jumpers and Connectors Locations of System Board of the machine type 2194 (Italy), 2197 and 6344 (EMEA/AP)
Jumper Settings of the System Board of the Machine Type 2194 (Italy), 2197 and 6344 (EMEA/AP) Table 5-1.Jumper settings of the System Board of the Machine Type 2194 (Italy), 2197 and 6344 (EMEA/AP) Jumper/Settings Function Bus Frequency(MHz) JP10 JP11 JP13 CPUCLK SDRAMCLK 2-3 2-3...
Connectors and Functions of System Board of the Machine Type 2194 (Italy), 2197 and 6344 (EMEA/AP) Table 5-2. Connectors and Functions of System Board of the Machine Type 2194 (Italy), 2197 and 6344 (EMEA/AP) Connector Function BAT 1 Battery socket Floppy 1 Floppy connector CPU FAN...
Layout of System Board of the Machine Type 6344 (US/Canada/LA) Jumpers and Connectors Locations of System Board of the machine type 6344 (US/Canada/LA) Jumper Settings of the System Board of the Machine Type 6344 (US/Canada/LA).The Jumper Ratio is determining by BIOS.
Connectors and Functions of System Board of the Machine Type 6344 (US/Canada/LA) Table 5-3. Connectors and Functions of System Board of the Machine Type 6344 (US/Canada/LA) Connector Function BATT Battery socket FDD 1 Floppy connector CPUFAN CPU FAN PCI Slot 1 PCI Slot 1 PCI Slot 2 PCI Slot 2...
Jumper Settings of the System Board of the Machine Type 2193 and 2196 Table 5-4. Jumper Settings of the System Board of the Machine Type 2193 and 2196 Jumper/Settings Function Bus Frequency(MHz) JP1 JP2 JP3 JP4 CPUCLK PCICLK 1-2 1-2...
Connectors and Functions of System Board of the Machine Type 2193 and 2196 Table 5-5. Connectors and Functions of System Board of the Machine Type 2193 and 2196 Connector Function BAT 1 Battery socket ATX Power connector CPU FAN Connector...
Jumper and Connector Settings of the System Board of the Machine Type 2194 and 6345 Table 5-6. Jumper and Connector Settings of the System Board of the Machine Type 2194 and 6345 I/O Ports Connector USB port. IDE1 For Primary IDE port. IDE2 For Secondary IDE port.
Page 151
CPU FAN : CPU cooling FAN Power Connector Pin No. Function GND. +12V SENSE PWR FAN: Power FAN Connector Pin No. Function GND. +12V SENSE SYS FAN: System FAN Connector Pin No. Function GND. +12V SENSE J9:Buzzer Enable (Optional) Pin No. Function Open Internal Buzzer Disable...
Page 152
2-3 close Normal operation (Default). J7: CD Audio Line in Pin No. Function CD_L CD_R JP11:AUX_IN Pin No. Function AUX_L AUX_R J14:Wake on LAN Pin No. Function +5VSB Signal JP3:TEL –The connector for Modem with internal voice connector. Pin No. Function Phone-in Mono-out...
Page 153
1-2-3open Recovery JP16: Top Block Lock Pin No. Function Open Top Block Lock Close Top Block Unlock (Default) JP15: Timeout Reboot Pin No. Function Open Timeout Reboot. Close No Reboot on Timeout. (Default) JP17: Onboard Sound function (Optional) Pin No. Function 1-2 close Enabled Sound.(Default)
Page 154
2-3 close Enable USB Device Wake up. JP20/JP21:Quad Speaker (Optional) Pin No. Function 1-2 close LINE_IN 2-3 close QUAD OUT JP24:FWH Write Protection Pin No. Function Open Normal (Default) Close Write Protection.
Page 155
J12 : For 2X11 Pins Jumper P+P−P− SPKR Soft PWR: Soft Power Connector Open: Normal Operation Short: Power On/Off RES: Reset Switch Open: Normal Operation Short: For Hardware Reset System P+P− − − − P− − − − : Power LED PIN 1 : LED anode (+) PIN 2 : LED cathode (−) PIN 3 : LED cathode (−)
Page 156
SPKR: Speaker Connector PIN 1 : VCC (+) − − − − PIN 2 : NC PIN 3 : NC PIN 4 : Data (−) HD: IDE Hard Disk Active LED PIN 1: LED anode (+) PIN 2: LED cathode (− − − − ) GN: Green Function Switch Open : Normal operation Short :Entering Green Mode...
Power Supply Cable Connector Specifications Refer to the following figures when checking for voltages on power supply cable connectors. When checking voltages, the power supply fan must be running. To power on the power supply without using the on/off switch, use a screwdriver or other tools to short the power supply connector (with the switch cable disconnected from the connector on the system board) or use a connection (jumper) to...
Main Output Pin Assignment Table 5-7. Main Output Pin Assignment Function Color +3.3 V Orange 3.3 V Orange COMMON BLACK +5Vdc COMMON BLACK +5Vdc COMMON BLACK POWER GOOD GRAY +5Vs PURPLE +12Vdc YELLOW 3.3V Orange -12Vdc BLUE COMMON BLACK P.S-on GREEN COMMON BLACK...
Page 159
Hard Drive or CD-ROM Power Cable Connector 3.5-In. Diskette Drive Power Cable Connector...
Factory-Installed Modem Card Layout Factory-Installed Modem Card Layout Factory-Installed Modem Card Connector Functions Item Function Connect to… Telephone line-out Telephone set Some modem adapters may come without this jack. Telephone line-in Telephone line NOTE: Care should be taken while connecting the voice- in/speaker-out connector.
3.5-In. Hard Disk Drive Jumper Locations & Settings 3.5-In. Hard Disk (Maxtor) Jumper Settings Locations Back of Drive (Quantum) AT Interface connector Jumper Configurations Slave Master Cable Select CS DS GNDGND Jumper Default Reserved DS with CS Setting Shown in for Slaves Position Parking...
CD-ROM Drive CD-ROM Front Panel NOTE: Position of CD-ROM switches and LEDs may vary from illustration. Item Description Load / eject button Headphone jack Power-on / busy indicator, lights up in green color while disc is set in ready state; lights up and flashes in amber color during data read or seek operation.
CD-ROM Drive Rear Panel Connectors and Features CABLE SELECT SLAVE DC INPUT AUDIO MASTER IDE INTERFACE NOT USED C S M R G G L S L A CD-ROM Rear Panel Item Function Connect to… Power supply connector Power supply Configuration jumper.
System Board Connector Pin Signals Monitor Port Signals Pin Signal Name Signal Name Red Video +5 V dc Green Video Synch Ground Blue Video No Connection No Connection Monitor ID Bit 1 Synch Ground Horizontal Synch Red Ground Vertical Synch Green Ground Monitor ID Bit 3 Blue Ground...
Data Bit 5 Ground Power Data Bit 6 Ground Power Data Bit 7 Ground Power Acknowledge Ground Power Busy Ground Power Paper Empty Ground Power Select Mouse Port Signals Pin Signal Name Signal Name Mouse Data +5 V dc Power No Connection Mouse Clock Ground...
Diskette Drive Cable Connector Signals Signal Name Pin Signal Name No Connection N/A 18 Direction SELECT Density Select Ground No Connection N/A 20 Step High Density Out Ground Ground N/A 22 Write Data No Connection N/A 23 Ground Ground N/A 24 Write GATE Index Ground...
IDE Cable Connector Signals Pin Signal Name Pin Signal Name Host Reset DMA Request Ground Ground Power Host Data 7 Host IOW Host Data 8 Ground Power Host Data 6 Host IOR Host Data 9 Ground Power Host Data 5 I/O Channel Ready Host Data 10 No Connection...
If any unsafe conditions are present, you must find out how serious the hazard is and if you can continue before you correct the hazard. All current IBM service supplements outlining feature/model changes, along with the machine history, should be reviewed. Check the following items: Damaged, missing, or changed parts, especially in the area of the On/Off switch and the power supply.
Parts Catalog Part Catalog of machine type 2193, 2194, and 6345 ..172 Assembly 1: System Unit ..........172 Assembly 2: Diskette Drive, Hard Disk Drive ....176 Assembly 3: CD-ROM, Modem Card......177 Assembly 4: Keyboard and Mouse ......180 Parts Catalog of machine type 2196, 219, and 6344 ..
Part Catalog of machine type 2193, 2194, and 6345 Assembly 1: System Unit Asm-Index FRU Number Description Gigabyte 810E,GA- 19K3582 6WMMC7/e1 System Board Pro283 (SiS540) AMD System 19K3284 Board (type 2193) AMD K6-2-500MHz 100FSB 10K2120 E7 (w/o heatsink and fan)
Page 173
19K3387 INTEL PIII 600MHz 133FSB 19K3388 INTEL, PIII 667MHz 133FSB Fansink, Supports PIII and 19K3292 Celeron 600MHz and up (PIII base) Processors Fansink, Supports K6-2 and 19K3348 Celeron (non-PIII base) Processors 19K3356 32MB module (PC100) 19K3293 64MB module (PC133) 19K3294 128MB module (PC133) 19K3308 95W Power Supply...
Page 174
14F0068 Power Cord Italy 02K0545 Power Cord China 13F9939 Power Cord ANZ 36L9015 Power Cord Japan Top Cover, Used w/Chenming 09N5397 Chassis Top Cover, Used w/Enlight 19K3593 Chassis 19K3314 Main (Bezel) Panel w/USB 09N5400 Main (Bezel) Panel 09N5398 Bezel Door (Aptiva) 19K3375 Bezel Door (PC300) Drive Bay Panels (3.5"...
Page 175
HDD-PWR LED/PWR Switch 1-15 19K3578 Cable Assembly for Gigabyte System board Y Audio Cable (for Gigabyte 1-16 19K3580 board) 1-16 19K3521 Y Audio Cable (for 2193) 1-17 19K3359 Speaker Port Bracket w/Cable CMOS Backup Battery 1-18 36L9077 (CR2032) 1-19 09N5409 Screw Pack...
Assembly 2: Diskette Drive, Hard Disk Drive Asm-Index FRU Number Description 19K3298 5 GB Hard Disk Drive, 3.5” 10K2059 10 GB Hard Disk Drive, 3.5” 19K3299 15 GB Hard Disk Drive, 3.5” 19K3355 20 GB Hard Disk Drive, 3.5” 36L9130 3.5”, Diskette Drive 19K3319 HDD IDE Cable (DMA 66 MHz)
Page 184
Norway, Netherlands, Finland, Belgium, Bosnia, Croatia, Egypt, Greece, Hungary, Poland, Portugal, Romania, Slovenia, Spain, Sweden, Turkey, LA (HI Volt), Danish, Swiss, Italy Jazz Speaker Power Adapter, TEAC-41-090400V Includes 19K3638 Scotland/England/Northern Island/Wales/GB/HK/Singapore/ United Arab Emirate (Dubai) Jazz Speaker Power Adapter, 19K3637 TEAC-41-090400V, ANZ, APU Jazz Speaker Power Adapter, 19K3641...
Part Catalog of machine type 2196, 2197, and 6344 Assembly 1: System Unit Asm-Index FRU Number Description 19K3284 Pro283 System board 19K3285 Pro286 System board Pro286 System board, for Celeron 19K3629 Processors only, w/ LAN 19K3584 MSI-6188 810E AMD K6-2-533MHz 100FSB E7 19K3286 (w/o heatsink and fan)
Page 186
Fansink, Supports K6-2 and 19K3348 Celeron Processors Fansink, Supports PIII Processors 19K3292 and Celeron 600 and up 19K3356 32MB module (PC100) 19K3293 64MB module (PC133) 19K3294 128MB module (PC133) 19K3309 95W Power Supply (LP) 95W used w/MSI-6188 810E 19K3585 Planar 6952301 Power Cord US/CE/CF/Taiwan 6952301...
Page 187
19K3330 PCMCIA Device 1-10 19K3320 Top Cover Main (Bezel) Panel 1-11 19K3321 w/USB/Audio/Volumn Main (Bezel) Panel 1-11 19K3322 wo/USB/Audio/Volumn Outer(Bezel) Panel w/FDD/CD- 1-12 19K3323 ROM slots, Blue, DT,Aptiva Outer(Bezel) Panel w/FDD/CD- 1-12 19K3324 ROM slots, Blue,DT,Aptiva Outer(Bezel) Panel w/FDD/CD- 1-12 19K3325 ROM slots, White (for PC300) Outer(Bezel) Panel w/FDD slot,...
Assembly 2: Diskette Drive, Hard Disk Drive Asm-Index FRU Number Description 19K3298 5GB Hard Disk Drive, 3.5” 10K2059 10 GB Hard Disk Drive, 3.5” 19K3299 15 GB Hard Disk Drive, 3.5” 19K3355 20 GB Hard Disk Drive, 3.5” 36L9130 3.5”, Diskette Drive 19K3341 Hard Disk Drive Cable 19K3340...
3395. The Fax-Back system file library can also be accessed through the PC Company BBS. The IBM Online Assistant will help you to diagnose and resolve technical problems by giving you access to the same tools used by IBM PC HelpCenter specialists. IBM Online Assistant guides...
Page 197
Multimedia, 40 Online Support Information, Parallel Port, 44, 53 Error Symptoms, 81 Port Signals, 165 Parts Catalog of machine type 2193, 2194 and 6345, 171 CD-ROM, Modem Card, Diskette Drive, Hard Disk Drive, 176 Keyboard and Mouse, 180 System Unit, 172...
Page 198
(Italy), 2197 and 6344 Real-Time Clock (EMEA/AP), 143 Error Symptoms 79 Error Symptoms, 76 Removals and Replacements of the machine type 2193, 2194 and 6345, 110 Adapter Cards, 114 Tools, 61 CD-ROM Drive, 118 Diskette Drive, 116 Hard Disk Drive, 119...
Page 199
Printed in U.S.A. International Business Machines Corporation Old Orchard Road, Armonk, New York 10504 Part Number: 19K2493 Pub Number: S19K-2493-00 3/00...