Page 1 Hardware Maintenance Service for Service Level A For Micro Tower Models Machine Type 2193, 2194 and 6345 For Desktop Models Machine Type 2196, 2197 and 6344...
Page 2 Note Before using this information and the product it supports, be sure to read the general information under on page 5. Second Edition (Feburary 2001) The following paragraph does not apply to any state or country where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION "AS IS"...
Page 3: Table Of Contents
Contents Notices ................................... 5 Voltage Supply Switch Settings ..........................5 Safety Information..............................6 Laser Compliance Statement..........................31 Trademarks................................32 Preface..................................33 General Information .............................. 35 Introduction ................................36 Product Overview..............................37 Hardware Interfaces..............................40 CMOS Reset................................41 Flash (BIOS) Update Procedure ..........................42 BIOS-contained Model Number and Serial Number ....................
Page 4 Removals and Replacements of machine type 2196, 2197, and 6344..............99 Identifying the Parts of the System Unit ........................100 Top Cover ..............................102 Adapter Cards..............................103 Diskette Drive..............................104 CD-ROM Drive ............................... 105 Hard Disk Drive.............................. 106 System Board ..............................107 Power Supply..............................
Page 5: Notices
Notices References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only IBM’s product, program, or service may be used.
Page 6: Safety Information
Safety Information DANGER To avoid a shock hazard, do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. To avoid shock hazard: The power cord must be connected to a properly wired and grounded receptacle.
Page 7 Caution: When replacing the battery, use only IBM Part Number 36L9077 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer.
Page 8 PERIGO Para evitar choques elétricos, não conecte ou desconecte nenhum cabo, nem efetue instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. Para evitar choques elétricos: O cabo de alimentação deve ser conectado a um receptáculo corretamente instalado e aterrado. Todos os equipamentos aos quais este produto será...
Page 9 cuidado: Ao substituir a bateria, utilize apenas o Número de Peça IBM 33F8354 ou um tipo de bateria equivalente recomendado pelo fabricante. Se seu sistema possuir um módulo com uma bateria de lítio, substitua-o apenas pelo mesmo tipo de módulo, produzido pelo mesmo fabricante. A bateria contém lítio e pode explodir se não for utilizada, manuseada e descartada de forma adequada.
Page 10 telecomunicação, redes e modems antes de abrir as tampas, a menos que receba outras instruções nos procedimentos de instalação e configuração.
Page 16 DANGER Pour éviter tout risque de choc électrique, ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration de ce produit au cours d'un orage. Pour éviter tout risque de choc électrique: Les cordons d'alimentation du présent produit et de tous les appareils qui lui sont connectés doivent être branchés sur des socles de prise de courant correctement câblés et mis à...
Page 17 attention: Remplacez la pile usagée par une pile de référence identique exclusivement - voir la référence IBM - ou par une pile équivalente recommandée par le fabricant. Si votre système est doté d'un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant.
Page 18 DANGER Certaines unités de CD-ROM contiennent une diode laser de classe 3A ou 3B. Prenez connaissance des informations suivantes : Rayonnement laser lorsque le carter est ouvert. Évitez de regarder fixement le faisceau ou de l'observer à l'aide d'instruments optiques. Évitez une exposition directe au rayon.
Page 19 VORSICHT Aus Sicherheitsgründen bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen. Aus Sicherheitsgründen: Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt anschließen. Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit ordnungsgemäß geerdetem Schutzkontakt anschließen. Signalkabel möglichst einhändig anschließen oder lösen, um einen Stromschlag durch Berühren von Oberflächen mit unterschiedlichem elektrischem Potential zu vermeiden.
Page 20 achtung: Eine verbrauchte Batterie nur durch eine Batterie mit der IBM Teilenummer 33F8354 oder durch eine vom Hersteller empfohlene Batterie ersetzen. Wenn Ihr System ein Modul mit einer Lithium-Batterie enthält, ersetzen Sie es immer mit dem selben Modultyp vom selben Hersteller. Die Batterie enthält Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder Entsorgung explodieren.
Page 21 VORSICHT Manche CD-ROM-Laufwerke enthalten eine eingebaute Laserdiode der Klasse 3A oder 3B. Die nachfolgend aufgeführten Punkte beachten. Laserstrahlung bei geöffneter Tür. Niemals direkt in den Laserstrahl sehen, nicht direkt mit optischen Instrumenten betrachten und den Strahlungsbereich meiden. 32 Kg 55Kg achtung: Beim Anheben der Maschine die vorgeschriebenen Sicherheitsbestimmungen beachten.
Page 22 PERICOLO Per evitare il pericolo di scosse elettriche durante i temporali, non collegare o scollegare cavi, non effettuare l'installazione, la manutenzione o la riconfigurazione di questo prodotto. Per evitare il pericolo di scosse elettriche: collegare il cavo di alimentazione ad una presa elettrica correttamente cablata e munita di terra di sicurezza;...
Page 23 ATTENZIONE: Quando si sostituisce la batteria, utilizzare solo una batteria IBM o batterie dello stesso tipo o di tipo equivalente consigliate dal produttore. Se il sistema di cui si dispone è provvisto di un modulo contenente una batteria al litio, sostituire tale batteria solo con un tipo di modulo uguale a quello fornito dal produttore.
Page 24 PERICOLO Alcune unità CD-ROM contengono all'interno un diodo laser di Classe 3A o Classe 3B. Prestare attenzione a quanto segue: Aprendo l'unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici ed evitare l'esposizione diretta al fascio.
Page 28 PELIGRO Para evitar una posible descarga eléctrica, no conecte ni desconecte los cables ni lleve a cabo ninguna operación de instalación, de mantenimiento o de reconfiguración de este producto durante una tormenta eléctrica. Para evitar una posible descarga: El cable de alimentación debe conectarse a un receptáculo con una instalación eléctrica correcta y con toma de tierra.
Page 29 caution: Al cambiar la batería, utilice únicamente la batería IBM Número de pieza 33F8354 o un tipo de batería equivalente recomendado por el fabricante. Si el sistema tiene un módulo que contiene una batería de litio, sustitúyalo únicamente por el mismo tipo de módulo del mismo fabricante. La batería contiene litio y puede explotar si no se utiliza, manipula o desecha correctamente.
Page 30 PELIGRO Algunas unidades de CD-ROM tienen incorporado un diodo de láser de Clase 3A o de Clase 3B Tenga en cuenta la siguiente información. Cuando la unidad está abierta se generan emisiones de rayos láser. No dirija la mirada al haz, no lo observe directamente con instrumentos ópticos y evite la exposición directa.
Page 31: Laser Compliance Statement
Laser Compliance Statement The CD/DVD-ROM drive in the computer is a laser product. The CD/DVD-ROM drive's classification label (sample shown below) is located on the drive CLASS 1 LASER PRODUCT APPAREIL A LASER CLASSE LASER KLASSE 1 LUOKAN 1 LASERLAITE PRODUIT LASER CATEGORIE 1 The CD/DVD-ROM drive is certified in the U.S.
Page 32: Trademarks
Trademarks The following are trademarks of the IBM Corporation in the United States or other countries or both: Operating System/2 OS/2 Personal System/2 HelpCenter PS/1 PS/2 Intel, Pentium, MMX, EtherExpress, and LANDesk are trademarks or registered trademarks of Intel Corporation. Microsoft, MS-DOS, Windows, and Windows NT are trademarks or registered trademarks of Microsoft Corporation.
Page 33: Preface
Preface This manual contains service information for the Service Level A (SL-A) model of the IBM Personal Computer, worldwide. This manual is intended to be used as a stand-alone document to service Machine types 2193, 2194, 2196, 2197, 6344 and 6345 product.
Page 35: General Information
General Information General Information .............................. 35 Introduction ................................36 Product Overview..............................37 Hardware Interfaces..............................40 CMOS Reset................................41 Flash (BIOS) Update Procedure ..........................42 BIOS-contained Model Number and Serial Number ....................43 BIOS Setup Utility ..............................44 Working with the Setup Menus ........................44 Start Options ..............................
Page 36: Introduction
Introduction This chapter gives a general overview of Machine Types 2193, 2194, 2196, 2197, 6344 and 6345, describes the standard and optional features, and details functional and environmental specifications. Machine Types 2196, 2197 and 6344 are desktop models and 2193, 2194 and 6345 are micro tower models.
Page 37: Product Overview
Product Overview All machine types mentioned above contain three PCI slots, and the system board support the AMD K6-2 and Intel Pentium III processors. Listed below are system features: Processors (Machine Types 2193 and 2196) Processor with the capabilities of 3D Now™! technology Socket-7 Zero Insertion Force (ZIF) connector.
Page 38 Digital Flat Panel port (only supported in some models) Microphone-in jack Line-out jack Line-in jack Diskette Drive AT-type 3.5-in. 1.44MB slimline diskette drive. Hard Disk Drive 3.5-in, 1-in. height IDE AT drive. 512 KB cache buffer in hard disk drive. Average and minimum 11.1 ms seek time, access time varies for the hard disk drive and the hard disk drive manufacturer.
Page 39 Modem 56.6 Kbps PCI Plug and Play modem adapter card with data/fax features. Telephone line-out (RJ-11) connector (Not available for all models). Telephone line-in (RJ-11) connector. IBM Monitor Super video graphics array (SVGA) monitor. Compliant to VESA power saving mode. Connector for a detachable grounded 3-wire power cord.
Page 40: Hardware Interfaces
Hardware Interfaces The following peripheral interfaces for adapters, options, and drives are supported in the system unit. Table 1-1 System Board Hardware Interfaces Item Interface Expansion slot Three PCI (peripheral component interconnect) v2.1 compatible for I/O adapter expansion slots that operate at 33 MHz bus speed. PCI slot 1 can cards hold a short (175mm) PCI adapter card.
Page 41: Cmos Reset
CMOS Reset This system does not deny access to the BIOS Setup Utility. Execute “Load BIOS Default Settings” in BIOS Setup to clear the corrupted CMOS data. See “Load Default Settings” on page 45.
Page 42: Flash (Bios) Update Procedure
Flash (BIOS) Update Procedure NOTE: The flash update procedure does not change the model number and serial number information in BIOS. Prepare a bootable DOS diskette with AWDFLASH.EXE and VXXYYZZ.BIN files NOTE: The AWDFLASH.EXE is flash utility programs. The VXXYYZZ.BIN is a BIOS source code binary file. Insert the diskette and boot from drive A.
Page 43: Bios-Contained Model Number And Serial Number
BIOS-contained Model Number and Serial Number The model number and serial number information is stored in BIOS ROM and displayed in the “Model Information” of BIOS Setup main menu. If a repair is completed by replacing the system board or installing a new BIOS ROM, then you need to enter the original system model number and serial number in the new BIOS ROM.
Page 44: Bios Setup Utility
BIOS Setup Utility The Setup Utility lets you review and change important information about the computer and its hardware. Working with the Setup Menus Starting the Setup Utility Follow these steps to enter Setup when the computer is off: 1. Turn on your monitor. 2.
Page 45: Changing Parameter Settings
The following table lists specific keys on the keyboard that will help you move through the Setup menus: Keys Function Down- or up- Use these arrow keys to highlight an option on the menu. arrow key (Press the Enter key to choose the option.) Left- or right- Use these arrow keys to make a selection and change an arrow key...
Page 46: Start Options
Start Options Setup automatically updates this menu when you do either of the following: Add or change hardware on your computer Make changes to other menus in Setup and save those changes To view the computer information such as the model number, serial number, and BIOS version and date, select the Product Data option from the Setup main menu.
Page 47: Advanced Setup
Report No FDD for Win 95 Select YES to release IRQ6 (Interrupt Request) when the system contains no floppy drive for compatibility with Windows 95 logo certification. Also select Disabled for the Onboard FDC Control Field in the Devices and I/O Ports menu. Halt on Determines under what conditions the power-on self test (POST) will halt when errors are detected.
Page 48: Usb Keyboard Support
USB Keyboard Support Select enabled to use a USB keyboard. The USB Controller must also be set to enabled. IDE Drives Setup PIO (Programmed Input/Output) IDE device driver controllers can support up to two separate drives. These drives have a master/slave relationship which is determined by the cabling configuration used to attach them to the controller.
Page 49: Power Management Setup
ONBOARD FDC CONTROLLER Allows you to enable or disable the diskette drive (floppy disk drive) controller. Game Port Address Determines the game port I/O address. Midi Port Address Determines the game port I/O address. Midi Port IRQ Determines the midi port IRQ (Interrupt Request) number. Power Management Setup The Power Management Setup allows you to configure your system to most effectively save energy while operating in a manner consistent with your own style of computer use.
Page 50: Specifications
Specifications Dimensions (width x depth x height): System unit: For Machine types 2193, 2194 and 6345: 190 mm (7.48 in.) x 370 mm (14.57 in.) x 380 mm (14.96 in.) For Machine types 2196, 2197 and 6344: 305 mm (12.45 in.) x 380.4 mm (14.97 in.) x 88 mm (3.46 in.) Weight: System unit: For Machine types 2193, 2194 and 6345:...
Page 51: Operating Requirements
Operating Requirements All machines require two power inputs: one on the system unit and one on the monitor display. The system unit comes with a voltage selector switch, allowing selection of either 115 V ac or 230 V ac. This switch must be in the 230 V ac position when the machine is plugged into a 230 V ac electrical outlet.
Page 52: Special Tools
Special Tools The following special tool is required to service this system when running the diagnostics program (PC-Doctor): Wrap plug, P/N 72X854...
Page 53: Checkprocedures
CheckProcedures Check Procedures ..............................53 Introduction ................................54 Start ..................................55 Index of Symptoms, Messages, Error Codes, or Beeps ..................57 Troubleshooting ..............................67 Factory-Installed Storage Devices ......................... 68 Factory-Installed Modem Card........................70 Audio (Not Supported by Diagnostics Program) .................... 71 CD-ROM Drive ...............................
Page 54: Introduction
Introduction This chapter contains the check procedures used to diagnose the causes of product failures. The diagnostic information consists of: Start: This is the starting point for any diagnostic action. Based on high-level symptoms, the check procedure directs you to more detailed procedures to help resolve machine failures.
Page 55: Start
Start This is the entry point for all check procedures. The check procedures use failure symptoms, Power-On Self Test (POST) error codes, or beeps to help determine the defective field replaceable unit (FRU). Follow the suggested check procedures or use the diagnostics diskette to determine the problem FRU. IMPORTANT: Replace FRUs ONLY when it is determined that the error is not a result of software, loose contacts, or dirty component surfaces.
Page 56 Make sure that the monitor refresh rate is correct. Note any symptoms, messages, error codes, or beeps. Make sure that there are no diskettes or CDs in the drives. 002 - DOES AN IBM LOGO SCREEN APPEAR? (YES, READ AHEAD. NO, GO TO STEP 004.) Insert the diagnostics diskette in the diskette drive.
Page 57: Index Of Symptoms, Messages, Error Codes, Or Beeps
Index of Symptoms, Messages, Error Codes, or Beeps How to Use Error Messages: Use the messages, error codes, and beeps combinations that occur to diagnose failures. If more than one failure occurs, diagnose from the first failure that appears. The cause of the first failure can result in false messages, error codes, or beeps.
Page 58 Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
Page 59 Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
Page 60 Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
Page 61 Table 2-2 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Action/FRU Messages, beeps NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure.
Page 62 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 63 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 64 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 65 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 66 Table 2-3 Error Symptoms List Error Symptoms Action/FRU NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
Page 67: Troubleshooting
Troubleshooting Failing Parts or Assemblies: The check procedures generally help you trace a problem to one part or assembly. The last step of the specific check procedure you are using indicates that a part or assembly is failing. You should inspect the part or assembly before you decide to replace it.
Page 68: Factory-Installed Storage Devices
Factory-Installed Storage Devices Use this check procedure to test any factory-installed drives. ATTENTION: The customer may have customized settings in the Setup Utility (other than default settings) on the computer you are servicing. Running the Setup Utility might alter those settings. Take note of the current settings and verify that the customer settings are in place when service is complete.
Page 69 005 – Select Diagnostics from the PC-Doctor diagnostics program main menu. Select and execute Floppy Disk Test if you want to test the diskette drive. Select and execute Hard Disk Test if you want to test the hard disk drive. Select Interactive Tests from the PC-Doctor diagnostics program main menu, then select and execute CD-ROM/DVD Test if you want to test the CD-ROM drive.
Page 70: Factory-Installed Modem Card
Factory-Installed Modem Card 001 - START Power off the system unit. In Windows 98 Device Manager, make sure that the modem is not configured with a conflicting COM port and IRQ setting. Make sure that the communication software is configured with the correct COM and IRQ settings (same COM port and IRQ as the modem).
Page 71: Audio (Not Supported By Diagnostics Program)
Audio (Not Supported by Diagnostics Program) NOTE: Audio tests for the sound card cannot be carried out in the PC Doctor DOS diagnostics program. It is, however, possible to carry out a dial tone test for the modem. While performing this check, you may need to enter and exit Microsoft Windows 98 several times. When instructed to select an icon or button, double-click on the item with the mouse.
Page 72 008 - Make sure that the volume control is not turned low. Make sure that the speaker and its adapter are not damaged. Make sure that the speaker is plugged into speak-out jack. Refer to Parts/Test Point Locations on page 111 If the error cannot be resolved, replace the system board.
Page 73: Cd-Rom Drive
CD-ROM Drive 001 - START Insert the diagnostics diskette into the diskette drive and make sure that there is no CD in the CD-ROM drive. Select Interactive Tests menu, then select and execute CD-ROM Test. 002 - DO YOU SEE A MESSAGE “NO CD-ROM DRIVE OR MSCDEX DEVICE DRIVER INSTALLED.” ? (YES, READ AHEAD.
Page 74: Memory
Memory 001 - START Power off the system unit. Insert the diagnostics diskette into the diskette drive. Make sure that all DIMMs are installed correctly. Power on the system unit. Take note of any messages, error codes, or symptoms. 002 - DO YOU RECEIVE POST MEMORY ERROR MESSAGE? (YES, READ AHEAD. NO, GO TO STEP 003) Enter BIOS Setup Utility then reboot the system.
Page 75: Keyboard
Keyboard 001 - START Power off the system unit and make sure that the keyboard plug is connected properly. 002 - Insert the diagnostics diskette into the diskette drive and power on the system unit. Select Interactive Tests menu, then execute Keyboard test. 003 - DOES THE KEYBOARD FUNCTION CORRECTLY? (YES, READ AHEAD.
Page 76: Mouse
Mouse NOTE: A sticking key button can cause the mouse to operate incorrectly. If you suspect this, go to "Keyboard" on page 75. 001 - START Make sure that the mouse ball turns freely. Make sure that the mouse plug connects properly. 002 - Power off the system unit.
Page 77: Power Supply
Power Supply 001 - START Power off the system unit. Check the power cord for continuity. Replace if necessary. Check for the correct line voltage from the power outlet, and verify that the voltage selector switch is set to the correct voltage.
Page 78 006 - ARE THE VOLTAGES CORRECT AND DOES THE FAN RUN? (YES, READ AHEAD. NO, GO TO STEP 009) The power supply is working normally. If you suspect the on/off switch cable assembly, see Step 003. If the fan continues to run when all connectors are plugged back in, go to “Undetermined Problems” on page 80. If the fan stops running when a drive connector is plugged back in, go to "Start"...
Page 79: Monitor
Monitor First, set the system to VGA mode. To do this in Windows 98, press the F8 function key during startup. Safe mode (VGA) will be set for Windows 98. Use the operating system's video setup to change the monitor resolution. If the monitor type is set to the power saving mode, the screen remains black and the LED lights or flashes in amber color.
Page 80: Undetermined Problems
Undetermined Problems If an error code is present, go to “Index of Symptoms, Messages, Error Codes, or Beeps” on page 57. If no error code is present, continue with this check. Check the power supply voltages (see “Power Supply Cable Connector Specifications" on page 127).
Page 81: Diagnostic Aids
Diagnostic Aids Diagnostic Aids ..............................81 Introduction ................................82 Power-On Self Test..............................83 Diagnostics Tools..............................84 Using Diagnostics Program from Recovery CD ..................... 84 Diagnostics Program Features........................84 Copyright IBM Corp. 2000...
Page 82: Introduction
Introduction This section explains the diagnostic aids, power-on self test (POST) and diagnostics program (PC-Doctor), that are available for troubleshooting problems on the system.
Page 83: Power-On Self Test
Power-On Self Test Each time you power-on the system, the power-on self test (POST) is initiated. Several items are tested during POST, but is for the most part transparent to the user. POST checks the following: System Board Mouse Memory Parallel Port(s) SVGA Controller Serial Port(s)
Page 84: Diagnostics Tools
Diagnostics Tools IMPORTANT: This manual is intended to test the IBM Machine Types 2193, 2194, 2196, 2197, 6344 and 6345 only. Testing devices which are not included with the original product package, including other IBM products, prototype cards, or modifying hardware settings may give false errors and invalid system responses. The diagnostics not specifically made for this model may also report incorrect errors and information.
Page 85 Table 3-1 Diagnostics Program Features Onboard Ethernet Hardware Info USB Port System Configuration Memory Contents IRQ and DMA Use Device Drivers COM and LPT Ports Physical Disk Drives Logical Disk Drives VGA Information Software Interrupts SCSI Devices I/O Use IDE Drive Info Network Information PCMCIA Information PCI Information...
Page 87: Repairing Information
Repair Information Repairing Information ............................87 Removals and Replacements of Machine types 2193, 2194, and 6345 ..............88 Identifying the Parts of the System Unit ........................89 Top Cover ..............................91 Adapter Cards..............................91 Diskette Drive..............................93 CD-ROM Drive ............................... 94 Hard Disk Drive..............................
Page 88: Removals And Replacements Of Machine Types 2193, 2194, And 6345
Removals and Replacements of Machine types 2193, 2194, and 6345 BEFORE REMOVING ANY FRU, POWER-OFF THE COMPUTER, UNPLUG ALL POWER CORDS FROM ELECTRICAL OUTLETS, THEN DISCONNECT ANY INTERCONNECTING CABLES. ATTENTION: The System board, processors, adapter cards, DIMMs, and upgrade processors can be damaged by electrostatic discharge.
Page 89: Identifying The Parts Of The System Unit
Identifying the Parts of the System Unit This computer system has 4 bays, each bay has a factory-installed drive in it. The devices are 3.5” Diskette, 40X CD-ROM drive (For 6345 system only some models have) and 5.0 GB hard disk (some models may have hard disk of 10 or 15 GB capacity).
Page 90 1.Power Supply This is a 95-watt switching power supply. 2.CD-ROM Drive This machine has a factory-installed 40 X CDROM drive. 3.Bay 2 This drive can accommodate a 5.25-inch device. 4.Hard Disk Drive This machine has a factory-installed 3.5” (10 or 15) GB hard disk drive. 5.Diskette Drive This machine has a factory-installed 3.5”...
Page 91: Top Cover
Top Cover To remove the top cover of this system unit: Remove the 4 screws that secure the top cover at the back of the system unit. Hold both sides of the system unit cover and push it backward about 25 mm. Lift the top cover up to remove it completely.
Page 92: Adapter Cards
Adapter Cards Installing Adapter Cards Remove the screw that secures the adapter card retainer and slot cover. Then remove the card retainer and slot cover. Align and insert the adapter card into the adapter card connector. Secure the card with the screw that you removed in the first step. Reinstall all hardware (except for the slot cover, which cannot be reinstalled) and screws that you removed prior to the installation of the adapter card.
Page 93: Diskette Drive
Diskette Drive To remove the diskette drive: Disconnect the power and signal cables from the back of the diskette drive. Remove the diskette mounting tray from the chassis as following illustration : Pivot the latch that secures the lower drive-mounting tray. Slide the drive-mounting tray toward the rear of the computer and remove it.
Page 94: Cd-Rom Drive
CD-ROM Drive To remove CD-ROM Drive: Disconnect the power, sound and signal cables from the CD-ROM. Remove the four screws (two on each side) that hold the CD-ROM drive to the chassis. Open the door on the front of the computer. Slide the CD-ROM drive forward through the front opening and remove it.
Page 95: Hard Disk Drive
Hard Disk Drive To remove or replace the hard disk drive: Make sure to disconnect the power and signal cables from the CD-ROM drive and the diskette drive. Pivot the latch that secures the lower drive-mounting tray. Slide the drive-mounting tray toward the rear of the computer and remove it.
Page 96: System Board
System Board To remove the system board from the system: To remove the system board, you must remove the adapter cards first. Disconnect the power cable, CD-ROM cable, Diskette Drive cable, Hard Disk Drive cable, audio cable, power switch cable, speaker cable and LED cable from system board. Remove the eight screws on system board.
Page 97: Power Supply
Power Supply This system has a 95-watt switching power supply. To remove the power supply, you must remove the top cover first. Disconnect the power cable from the riser board and all drives. Remove the screws in the machine rear that secure the power supply.
Page 98: Memory (Dimm)
Memory (DIMM) This system has 2 system memory module sockets, DIMM 0 and DIMM 1. These sockets hold dual in line memory modules (DIMM) that contains 3.3V single or double-sided synchronous DRAM (SDRAM). The maximum memory size is 512MB total.
Page 99: Removals And Replacements Of Machine Type 2196, 2197, And 6344
Removals and Replacements of machine type 2196, 2197, and 6344 Before Removing any FRU, Power-OFF The COMPUTER UNPLUG, ALL POWER CORDS FROM ELECTRICAL OUTLETS, THEN DISCONNECT ANY INTERCONNECTING CABLES. ATTENTION: The System board, processors, adapter cards, DIMMs, and upgrade processors can be damaged by electrostatic discharge.
Page 100: Identifying The Parts Of The System Unit
Identifying the Parts of the System Unit This computer system has 3 bays, each bay has a factory-installed drive in it. The devices are 3.5” Diskette, 40X CD-ROM drive and 5.0 GB hard disk (some models may have hard disk of 10 or 15 GB capacity). Diskette drives in this unit use the standard diskette advanced technology (AT) Interface.
Page 101 1. Power Supply This is a 95-watt switching power supply. 2. Expansion slots On the rear panel of the system unit are 3 slot openings for installation of adapter card. 3. Modem card This system may include a V.90 Data/Fax modem. For 6344 systems will use the Ethernet card.
Page 102: Top Cover
Top Cover To remove the top cover of this system unit: Remove the screws that secure the top cover at the back of the system unit. Hold both sides of the system unit top cover and push it forward about 25 inches. Lift the top cover up to remove it completely.
Page 103: Adapter Cards
Adapter Cards Installing Adapter Cards Remove the screw that secures the adapter card retainer and slot cover. Then remove the card retainer and slot cover. Align and insert the adapter card into the adapter card connector. Secure the card with the screw that you removed in the first step. Reinstall all hardware (except for the slot cover, which cannot be reinstalled) and screws that you removed prior to the installation of the adapter card.
Page 104: Diskette Drive
Diskette Drive To remove the diskette drive: Disconnect the power and signal cables from the back of the diskette drive. Pull up the latch that secures the drive-mounting tray. Slide the drive-mounting tray toward the front of the computer and remove it Remove the four screws (two on each side) that secure the bay holder.
Page 105: Cd-Rom Drive
CD-ROM Drive To remove CD-ROM Drive: Disconnect the power, sound and signal cables from the CD-ROM. Pull up the latch that secures the CD-ROM drive-mounting tray. Slide the drive-mounting tray toward the back of the computer and remove it. Remove four screws (two on each side) that secure the bay holder. Pull the bay holder backward and lift it up to remove it completely.
Page 106: Hard Disk Drive
Hard Disk Drive To remove or replace the hard disk drive: Follow the above steps to remove the CD-ROM. Make sure to disconnect the power cord and signal cables from the hard disk drive and the diskette device. Remove the screws that secure the bay holder that holds the hard diskette drive. Pull the bay holder right to uncouple it from the chassis completely and lift it up.
Page 107: System Board
System Board To remove the system board from the system: To remove the system board, you must remove the adapter cards first. Disconnect the power cable, CD-ROM cable, Diskette Drive cable, Hard Disk Drive cable, audio cable, power switch cable, speaker cable and LED cable from system board. Remove the eight screws on system board.
Page 108: Power Supply
Power Supply This system has a 95-watt switching power supply. To remove the power supply, you must remove the top cover first. Disconnect the power cable from the riser board and all drives. Remove the screws in the machine rear that secure the power supply.
Page 109: Memory (Dimm)
Memory (DIMM) This system has 2 system memory module sockets, DIMM 0 and DIMM 1. These sockets hold dual in line memory modules (DIMM) that contains 3.3V single or double-sided synchronous DRAM (SDRAM). The maximum memory size is 512MB total.
Page 111: Parts/Test Point Locations
Parts/Test Point Locations Parts/Test Point Locations ........................... 111 Introduction ................................112 Layout of System Board of Machine Types 2194 (Italy), 2197 and 6344 (EMEA/AP)..........113 Jumper Settings of the System Board of Machine Types 2194 (Italy), 2197 and 6344 (EMEA/AP)....114 Connectors and Functions of System Board of Machine Types 2194 (Italy), 2197 and 6344 (EMEA/AP)..
Page 112: Introduction
Introduction This chapter contains system board layouts and jumper settings. It is useful when you are asked to measure voltages. Use this information to help you locate parts such as electronic boards, connectors, pin numbers, and test points. This chapter also contains jumper settings for the hard disk drive, CD-ROM (compact disc-read-only memory) drive, and the connector information for modem adapter card.
Page 113: Layout Of System Board Of Machine Types 2194 (Italy), 2197 And 6344 (Emea/Ap)
Layout of System Board of Machine Types 2194 (Italy), 2197 and 6344 (EMEA/AP) Jumpers and Connectors Locations of System Board of Machine Types 2194 (Italy), 2197 and 6344 (EMEA/AP)
Page 114: Jumper Settings Of The System Board Of Machine Types 2194 (Italy), 2197 And 6344 (Emea/Ap)
Jumper Settings of the System Board of Machine Types 2194 (Italy), 2197 and 6344 (EMEA/AP) Table 4-1 Jumper settings of the System Board of Machine Types 2194 (Italy), 2197 and 6344 (EMEA/AP) Jumper/Settings Function Bus Frequency(MHz) JP9 JP10 JP11 JP13 CPUCLK SDRAMCLK 2-3 2-3...
Page 115: Connectors And Functions Of System Board Of Machine Types 2194 (Italy), 2197 And 6344 (Emea/Ap)
Connectors and Functions of System Board of Machine Types 2194 (Italy), 2197 and 6344 (EMEA/AP) Table 4-2 Connectors and Functions of System Board of Machine Types 2194 (Italy), 2197 and 6344 (EMEA/AP) Connector Function BAT 1 Battery socket Floppy 1 Floppy connector CPU FAN LAN and USB connector...
Page 116: Layout Of System Board Of Machine Type 6344 (Us/Canada/La)
Layout of System Board of Machine Type 6344 (US/Canada/LA) Jumpers and Connectors Locations of System Board of Machine Type 6344 (US/Canada/LA) Jumper Settings of the System Board of Machine Type 6344 (US/Canada/LA). The Jumper Ratio is determining by BIOS.
Page 117: Connectors And Functions Of System Board Of Machine Type 6344 (Us/Canada/La)
Connectors and Functions of System Board of Machine Type 6344 (US/Canada/LA) Table 4-3 Connectors and Functions of System Board of Machine Types 6344 (US/Canada/LA) Connector Function BATT Battery socket FDD 1 Floppy connector CPUFAN CPU FAN PCI Slot 1 PCI Slot 1 PCI Slot 2 PCI Slot 2 PCI Slot 3...
Page 118: Layout Of System Board Of Machine Types 2193 And 2196
Layout of System Board of Machine Types 2193 and 2196 Jumpers and Connectors Locations of System Board of Machine Types 2193 and 2196...
Page 119: Jumper Settings Of The System Board Of Machine Types 2193 And 2196
Jumper Settings of the System Board of Machine Types 2193 and 2196 Table 4-4 Jumper Settings of the System Board of Machine Types 2193 and 2196 Jumper/Settings Function Bus Frequency (MHz) JP1 JP2 JP3 JP4 CPUCLK SDRAMCLK 1-2 1-2 2-3 1-2 2-3 2-3 2-3 1-2 1-2 1-2...
Page 120: Connectors And Functions Of System Board Of Machine Types 2193 And 2196
Connectors and Functions of System Board of Machine Types 2193 and 2196 Table 4-5 Connectors and Functions of System Board of Machine Types 2193 and 2196 Connector Function BAT 1 Battery socket ATX Power connector CPU FAN Connector Hard Disk connector (Primary IDE) CD-ROM Drive connector (Secondary IDE) Digital Flat Panel connector USB and LAN connector...
Page 121: Layout Of System Board Of Machine Types 2194 And 6345
Layout of System Board of Machine Types 2194 and 6345 Game & PS/2 COMA JP14 Audio AC97 JP19 JP11 JP18 JP20 JP21 SDRAM 8810 SDRAM JP23 GMCH 82810 810E 6WMMC7-1 ICH/ JP16 JP15 82801 FWH32 DIMM 1 JP13 JP12 JP24 DIMM 2 POWER IDE 2...
Page 122: Jumper And Connector Settings Of The System Board Of Machine Types 2194 And 6345
Jumper and Connector Settings of the System Board of Machine Types 2194 and 6345 Table 4-6 Jumper and Connector Settings of the System Board of Machine Types 2194 and 6345 I/O Ports Connector USB port. IDE1 For Primary IDE port. IDE2 For Secondary IDE port.
Page 123 SYS FAN: System FAN Connector Pin No. Function GND. +12V SENSE J9: Buzzer Enable (Optional) Pin No. Function Open Internal Buzzer Disable Close Internal Buzzer Enable J17 RING PWR ON :Internal Modem Card Ring PWR On Pin No. Function Signal JP2: Keyboard Power On Selection Pin No.
Page 124 JP3: TEL –The connector for Modem with internal voice connector. Pin No. Function Phone-in Mono-out JP1: STR Enable Pin No. Function Close STR Enable Open STR Disable (Default) JP14: Case Open Pin No. Function Signal JP13: Safe Mode/Recovery/Normal Pin No. Function 1-2 close Normal (Default)
Page 125 J19: Front Panel USB Port (Optional) Pin No. Function 1,4,5,10 3,7,9 USB P0+ USB P0- JP18: SPDIF (Optional) Pin No. Function SPDIF OUT JP19: USB Device Wake up Pin No. Function 1-2 close Disable USB Device Wake up (Default). 2-3 close Enable USB Device Wake up.
Page 126 P+P P : Power LED PIN 1: LED anode (+) PIN 2: LED cathode ( ) PIN 3: LED cathode ( ) SPKR: Speaker Connector PIN 1: VCC (+) PIN 2: NC PIN 3: NC PIN 4: Data ( ) HD: IDE Hard Disk Active LED PIN 1: LED anode (+) PIN 2: LED cathode ( )
Page 127: Power Supply Cable Connector Specifications
Power Supply Cable Connector Specifications Refer to the following figures when checking for voltages on power supply cable connectors. When checking voltages, the power supply fan must be running. To power on the power supply without using the on/off switch, use a screwdriver or other tools to short the power supply connector (with the switch cable disconnected from the connector on the system board) or use a connection (jumper) to short the black and green wires of the 20-pin connector on power supply.
Page 128: Main Output Pin Assignment
Main Output Pin Assignment Table 4-7 Main Output Pin Assignment Function Color +3.3 V Orange 3.3 V Orange COMMON BLACK +5Vdc COMMON BLACK +5Vdc COMMON BLACK POWER GOOD GRAY +5Vs PURPLE +12Vdc YELLOW 3.3V Orange -12Vdc BLUE COMMON BLACK P.S-on GREEN COMMON BLACK...
Page 129 Hard Drive or CD-ROM Power Cable Connector 3.5-In. Diskette Drive Power Cable Connector...
Page 130: Factory-Installed Modem Card Layout
Factory-Installed Modem Card Layout Factory-Installed Modem Card Layout Factory-Installed Modem Card Connector Functions Item Function Connect to… Telephone line -out Telephone set Some modem adapters may come without this jack. Telephone line-in Telephone line NOTE: Care should be taken while connecting the voice-in/speaker-out connector. The longer exposed end (approx. 15mm) of the cable should be connected to the modem card.
Page 131: 3.5-In. Hard Disk Drive Jumper Locations & Settings
3.5-In. Hard Disk Drive Jumper Locations & Settings 3.5-In. Hard Disk (Maxtor) Jumper Settings Locations Back of Drive (Quantum) AT Interface connector Jumper Configurations Slave Master Cable Select CS DS GNDGND Jumper Default DS with CS Reserved Setting Shown in for Slaves Position Parking...
Page 132: Cd-Rom Drive
CD-ROM Drive CD-ROM Front Panel NOTE: Position of CD-ROM switches and LEDs may vary from illustration. Item Description Load / eject button Headphone jack Power-on / busy indicator, lights up in green color while disc is set in ready state; lights up and flashes in amber color during data read or seek operation.
Page 133: Cd-Rom Drive Rear Panel Connectors And Features
CD-ROM Drive Rear Panel Connectors and Features CABLE SELECT SLAVE DC INPUT IDE INTERFACE AUDIO MASTER NOT USED C S M R G G L S L A CD-ROM Rear Panel Item Function Connect to… Power supply connector Power supply Configuration jumper.
Page 134: Dimm Configurations
DIMM Configurations The system board has two DIMM sockets. A maximum of 512MB memory may be installed. You can install 16MB, 32MB, 64MB, 128MB, or 256MB DIMMs in any sockets and with any combinations.
Page 135: System Board Connector Pin Signals
System Board Connector Pin Signals Monitor Port Signals Signal Name Signal Name Red Video +5 V dc Green Video Synch Ground Blue Video No Connection No Connection Monitor ID Bit 1 Synch Ground Horizontal Synch Red Ground Vertical Synch Green Ground Monitor ID Bit 3 Blue Ground Serial Port Signals...
Page 136: Keyboard Port Signals
Keyboard Port Signals Signal Name Signal Name Keyboard Data +5 V dc Power Mouse Data Keyboard Clock Ground Power Mouse Clock...
Page 137: Diskette Drive Cable Connector Signals
Diskette Drive Cable Connector Signals Signal Name Signal Name No Connection Direction SELECT Density Select Ground No Connection Step High Density Out Ground Ground Write Data No Connection Ground Ground Write GATE Index Ground Ground Track 0 No Connection Ground Ground Write Protect Drive Select 1...
Page 138: Ide Cable Connector Signals
IDE Cable Connector Signals Signal Name Signal Name Host Reset DMA Request Ground Ground Power Host Data 7 Host IOW Host Data 8 Ground Power Host Data 6 Host IOR Host Data 9 Ground Power Host Data 5 I/O Channel Ready Host Data 10 No Connection Host Data 4...
Page 139: Safety Inspection Guide
Safety Inspection Guide General Guidelines ..............................140...
Page 140: General Guidelines
General Guidelines The purpose of this Safety Inspection Guide is to help you identify possible unsafe conditions on machines that are being inspected for a Maintenance Agreement. Each machine has necessary functions items installed to provide the operators and service personnel with an acceptable level of safety. This guide lists only these items. Good judgment should be used to identify possible safety conditions not covered by this Safety Inspection Guide.
Page 141: Parts Catalog
Parts Catalog Parts Catalog of machine type 2193, 2194, and 6345 .................... 142 Assembly 1: System Unit ..........................142 Assembly 2: Diskette Drive, Hard Disk Drive ....................145 Assembly 3: CD-ROM, Modem Card ......................146 Assembly 4: Keyboard and Mouse ........................ 148 Parts Catalog of machine type 2196, 2197, and 6344 ....................
Page 142: Parts Catalog Of Machine Type 2193, 2194, And 6345
Parts Catalog of machine type 2193, 2194, and 6345 Assembly 1: System Unit Asm-Index FRU Number Description 19K3582 Gigabyte 810E,GA-6WMMC7/e1 System Board 24P6027 Pro283 (SiS540) AMD System Board (type 2193) 24P6026 Pro 283I System Board 10K2120 AMD K6-2-500MHz 100FSB E7 (w/o heatsink and fan) 19K3286 AMD K6-2-533MHz 100FSB E7 (w/o heatsink and fan) 19K3412...
Page 143 19K3293 64MB module (PC133) 19K3294 128MB module (PC133) 19K3308 95W Power Supply 6952301 Power Cord US/CE/CF/Taiwan 6952301 Power Cord LA-Lo Voltage 13F9978 Power Cord LA-Lo Voltage 13F9939 Power Cord Brazil 36L8879 Power Cord APU Countries 14F0032 Power Cord UK/HK/Singapore 13F9978 Power Cord Euro 14F0050 Power Cord Swiss...
Page 144 1-11 19K3315 Chassis (w/o power supply) w/USB (Chenming) 1-11 19K3594 Chassis (w/o power supply) w/o USB (Enlight) 1-11 19K3602 Chassis (w/o power supply) w USB (Enlight) 3.5" FDD/HDD (Holder) Bracket, Used w/Chenming 1-12 09N5401 Chassis 3.5" FDD/HDD (Holder) Bracket, Used w/Enlight 1-12 19K3595 Chassis...
Page 145: Assembly 2: Diskette Drive, Hard Disk Drive
Assembly 2: Diskette Drive, Hard Disk Drive Asm-Index FRU Number Description 19K3298 5 GB Hard Disk Drive, 3.5” 10K2059 10 GB Hard Disk Drive, 3.5” 19K3299 15 GB Hard Disk Drive, 3.5” 19K3355 20 GB Hard Disk Drive, 3.5” 36L9130 3.5”, Diskette Drive 19K3319 HDD IDE Cable (DMA 66 MHz)
Page 146: Assembly 3: Cd-Rom, Modem Card
Assembly 3: CD-ROM, Modem Card Asm-Index FRU Number Description 19K3360 40X CD-ROM, White 19k3300 48XCD-ROM, White 19K3301 32X CD-RW, White 19K3349 40X CD-ROM, Black Bezel 19K3358 CD-ROM IDE Cable 09N5406 CD-ROM Audio Cable (2194) 19K3337 CD-ROM Audio Cable (2193) 19K3302 40X/8X DVD-ROM, White 19K3350 40X/8X DVD-ROM, Black Bezel...
Page 147 01N1872 Modem Phone Cable Adapter Australia 01N1874 Modem Phone Cable Adapter NZ Modem Phone Cable Adapter 60H6043 Spain/Southern Ireland 60H6045 Modem Phone Cable Adapter Australia 60H6046 Modem Phone Cable Adapter Belgium 60H6047 Modem Phone Cable Adapter Denmark 60H6048 Modem Phone Cable Adapter Norway/Finland 60H6049 Modem Phone Cable Adapter FR 60H6050...
Page 148: Assembly 4: Keyboard And Mouse
Assembly 4: Keyboard and Mouse Asm-Index FRU Number Description 10L6145 Mouse, Badger 28L1865 Mouse, Scrollpoint II 37L2590 104 US ENGLISH 103P 37L2591 105 FR CANADIAN 058 (Commercial) 37L2592 105 FR CANADIAN 445 (Consumer) 37L2593 105 LA SPANISH 171 37L2594 105 BRAZILIAN/PORTUGUESE 275 37L2595 105 ARABIC 253 37L2596...
Page 149 37L2606 105 SWED/FINNISH 153 37L2607 105 SWISS 150 37L2608 105 UK ENGLISH 166 37L2609 104 US ENGLISH-EMEA 103P ANZ 37L2610 109 JAPANESE 194 37L2611 104 CHINESE/US 467 HK/TW 37L2612 105 BELGIUM FRENCH 120 37L2640 105 ICELANDIC 197 104 PALM REST US ENG 103P 37L2514 US/CHINA/ANZ/Singapore 37L0912...
Page 150 37L2532 105 PALM REST, EURO NORWEGIAN 155 37L2533 105 PALM REST POLISH 214 37L2534 105 PALM REST PORTUGUESE 163 37L2535 105 PALM REST ROMANIAN 446 37L2536 104 PALM REST RUSSIAN 443 37L2537 105 PALM REST SERBIAN/CYR 118 37L2538 105 PALM REST SLOVIC 245 37L2539 105 PALM REST, EURO SPANISH 145 37L2540...
Page 151 10K2597 Speaker Power Adapter China 10K2593 Speaker Power Adapter Japan 10K2789 Speaker Power Adapter Brazil 19K3635 Jazz Speaker J-205A, Active, PC99 Jazz Speaker Power Adapter PPI-0940-UL US, LA LoVolt), Cnada, Mexico, Peru, Colobia, Ecuador, 19K3636 Venezuela, Bolivia, Panama, EI S alvador, Honduras, Nicaragua, Dominican Republic, Guatemala, Taiwan, Saudi Arabia, Thailand Jazz Speaker Power Adapter, TEAC-41-090400V,...
Page 152: Parts Catalog Of Machine Type 2196, 2197, And 6344
Parts Catalog of machine type 2196, 2197, and 6344 Assembly 1: System Unit Asm-Index FRU Number Description 24P6027 Pro283 System board 24P6028 Pro286 System board 24P6030 Pro286 System board 19K3584 MSI-6188 810E AMD K6-2-533MHz 100FSB E7 (w/o heatsink 19K3286 and fan) AMD K6-2-550MHz 100FSB E7 (w/o heatsink 19K3412 and fan)
Page 153 19K3356 32MB module (PC100) 19K3293 64MB module (PC133) 19K3294 128MB module (PC133) 19K3309 95W Power Supply (LP) 95W Power Supply used w/MSI-6188 810E 19K3585 Planar 6952301 Power Cord US/CE/CF/Taiwan 6952301 Power Cord LA-Lo Voltage 36L8879 Power Cord APU Countries Power Cord, UK/HK/Singapore/United Arab 14F0032 Emirate (Dubai) Power Cord (Euro) France, Germany, Sweden,...
Page 154 Outer (Bezel) Panel w/FDD/CD-ROM slots, Blue, 1-12 19K3324 DT, Aptiva Outer (Bezel) Panel w/FDD/CD-ROM slots, 1-12 19K3325 White (for PC300) 1-12 19K3326 Outer (Bezel) Panel w/FDD slot, White 1-13 19K3327 FDD (Holder) Bracket 1-14 19K3328 HDD (Holder) Bracket 1-15 19K3329 CD-ROM (Holder) Bracket 1-16 19K3331...
Page 155: Assembly 2: Diskette Drive, Hard Disk Drive
Assembly 2: Diskette Drive, Hard Disk Drive Asm-Index FRU Number Description 19K3298 5GB Hard Disk Drive, 3.5” 10K2059 10 GB Hard Disk Drive, 3.5” 19K3299 15 GB Hard Disk Drive, 3.5” 19K3355 20 GB Hard Disk Drive, 3.5” 36L9130 3.5”, Diskette Drive 19K3341 Hard Disk Drive Cable 19K3340...
Page 156: Assembly 3: Cd-Rom, Modem Card
Assembly 3: CD-ROM, Modem Card Asm-Index FRU Number Description 19K3360 40X CD-ROM, White 19k3300 48XCD-ROM, White 19K3301 32X CD-RW, White 19K3413 32X CD-ROM, Black Bezel 19K3643 48X CD-ROM, Black Bezel 19K3349 40 X CD-ROM, Black Bezel 19K3342 CD-ROM Cable 09N5406 CD-ROM Audio Cable (for MSI board) 19K3337 CD-ROM Audio Cable (for Pro board)
Page 157 01N1874 Phone Cord Adapter NZ...
Page 158: Assembly 4: Keyboard And Mouse
Assembly 4: Keyboard and Mouse Asm-Index FRU Number Description 10L6145 Mouse, Badger 28L1865 Mouse, Scrollpoint II 37L2609 104 US ENGLISH-EMEA 103P 37L2610 ANZ 109 JAPANESE 194 37L2611 104 CHINESE/US 467 HK/TW 104 PALM REST US ENG 103P 37L2514 US/CHINA/ANZ/Singapore 37L0912 105 PALM REST FR CANADIAN 058 (Commercial) 37L2516 105 PALM REST LA SPANISH 171...
Page 159 37L2528 104 PALM REST HEBREW 212 37L2529 105 PALM REST HUNGARIAN 208 37L2530 105 PALM REST ICELANDIC 197 37L2531 105 PALM REST, EURO ITALY 142 37L2532 105 PALM REST, EURO NORWEGIAN 155 37L2533 105 PALM REST POLISH 214 37L2534 105 PALM REST PORTUGUESE 163 37L2535 105 PALM REST ROMANIAN 446 37L2536...
Page 160: Appendix A. Online Support Information
Appendix A. Online Support Information This section describes online technical support services available to help repair the computer. This section covers: IBM PC Company Fax-Back Service IBM useful sites on the World Wide Web (WWW) IBM Online Assistant Discussion Forums The IBM PC Company offers online resources including several Internet World Wide Web sites, the IBM Online HelpCenter support areas, and a Fax-Back service.
Page 161: Index
Index Adapter Cards Hard Disk Drive 38, 95 Installing, 92 3.5-In. Jumper Locations & Settings, 131 Removing, 92 32-bit Access, 40 Audio Check Procedure, 68 Check Procedure, 71 Error Symptoms, 63 Error Symptoms, 64 PIO Mode, 48 Hard Disk Drive, 40 Beeps, 54, 57, 57 BIOS Flash Update Procedure, 42...
Page 162 Keyboard and Mouse, 158 Error Symptoms, 62 System Unit, 152 Parts/Test Point Locations, 111 Password Tools, 52 Setting, 49 PCI, 40 PIO Mode, 48 Undetermined Problems POST, 55 Check Procedure, 80 Power Consumption, 50 USB, 40 Power Management, 38, 48 Power Supply, 38 Check Procedure, 77 Video, 37...
Page 163 Printed in U.S.A. International Business MachinesCorporation Old Orchard Road, Armonk, New York 10504 Part Number: 19K2493 Pub Number: S19K-2493-00 3/00...

This manual is also suitable for:

Aptiva Netvista a20 2193 2194 6345 2196 ... Show all

IBM PC 300 Maintenance Service Manual

Quick Links

Related Manuals for IBM PC 300

Summary of Contents for IBM PC 300

This manual is also suitable for:

Table of Contents