Advertisement
PARTS LIST CONTINUED
19 19
19 19
19
item
PARTS
no.
LIST
Description
78
BOLT CARRIAGE 5/16-18x3/4"
79
LINE PVC
80
81
82
83
CONNECTOR BAG QUICK
84
LABEL READ OWNER'S MANUAL
85
TAMPER
86
LABEL EAR/EYE BREATING
87
20
20 20
20 20
TROUBLESHOOTING
Problem
Will not vacuum or has poor vacuum perfor-
mance.
Poor chipping performance.
Engine stalls or labors when chipping.
Abnormal vibration.
Engine will not start.
Engine is locked, will not
pull over.
Engine Service and Warranty
22.1
22.1
22.1
22.1
22.1
Contact your nearest engine manufacturer's autho-
rized servicing dealer.
R
ecord your machine model, serial number
21 21
21 21
Serial Plate
21
and date-of-purchase and where purchased
L
A
R
98
Model
L
A
Unit(Weight)
p
108
lbs.
Operator
Purchase
Purchased
from
Date
Part No. 890394
( Continued from page 11 )
KD510
QTY
KD510IC
Part No.
Part No.
-
-
-
-
890176
1
890301
1
-
-
890254
1
Before Requesting Service Review These Suggestions
Possible Cause
Dirty debris bag. Nozzle height set too high or too low.
Hose kit cap missing. Clogged nozzle or exhaust.
Excessive quantity of debris.
Extremely hard wood. Dull or damaged chipper blade.
Feeding branches into chipper too rapidly. Engine
service may be required.
Loose or out of balance impeller or loose engine.
Stop switch off (Honda only). Throttle in off position.
Engine not in full choke position (Honda only). Out of
gasoline. Bad or old gasoline. Spark Plug wire
disconnected. Dirty air cleaner.Safety Interlock engaged.
Debris locked in chipper blade, hopper or inside
impeller. Engine problem.
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO
64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Serial No.
Engine Power
kg
kW
QTY
KD510H
QTY
KD510HS
Part No.
Part No.
-
-
-
-
8024039
-
-
-
-
890176
1
890176
1
890301
1
890301
1
-
-
-
-
890254
1
890254
1
890254
22 22
22 22
22
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
rpm
-1
min
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
BILLY GOAT INDUSTRIES INC.
P.O. BOX 308 (1803 S JEFFERSON) LEE'S SUMMIT, MO 64063 / USA
R
PHONE: 816-524-9666 FAX: 816-524-6983
Page 12 of 12
QTY TKD510IC
QTY TKD510H
Part No.
2
-
-
900732
1
-
-
890176
1
890176
1
890301
1
890301
1
-
-
890229
1
1
890254
1
Solution
Clean debris bag. Shake bag clean or wash. Adjust
nozzle height. Check for hose kit cap. Unclog nozzle or
exhaust (see page 5). Allow air to feed with debris.
Avoid extremely hard wood. Sharpen or replace
chipper blade (see page 8).
Feed branches at a slower rate. Service engine.
Check impeller and replace if required. Check
Engine.
Check stop switches, throttle, choke position and
gasoline. Connect spark plug wire. Clean or replace
air cleaner. Or contact a qualified service person.
Quick Disconnect not fully engaged.
See page 5, Clearing a clogged chipper hopper.
Contact an engine servicing dealer for engine
problems.
WARRANTY PROCEDURE
Form No. F011398B
QTY
* Denotes
Part No.
standard
-
-
hardware
-
-
item that
may be
purchased
locally.
890176
1
890301
1
-
-
890254
1
Advertisement
