Mitsubishi Heavy Industries FDTCVA SERIES Technical Manual page 83

Model FDKNVA251HEN1R
Item
(1)
Nominal cooling capacity
Nominal heating capacity (1)
Power source
Cooling power consumption
Running current (Cooling)
Power factor (Cooling)
Heating power consumption
Running current (Heating)
Power factor (Heating)
Inrush current (L.R.A)
Noise level
Exterior dimensions
Height × Width × Depth
Net weight
Refrigerant equipment
Compressor type & Q'ty
Starting method
Heat exchanger
Refrigerant control
Refrigerant
Quantity
Refrigerant oil
Defrost control
Air handling equipment
Fan type & Q'ty
Motor
Starting method
Air fl ow
Outside air intake
Air filter, Q'ty
Shock & vibration absorber
Electric heater
Operation control
Operation switch
Room temperature control
Safety equipment
Installation data
Refrigerant piping size
Connecting method
Drain hose
Insulation for piping
Accessories
Optional parts
Notes (1) The data are measured at the following conditions.
Operation
Cooling
Heating
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 "UNITARY AIR-CONDITIONERS"
(3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz.
(4) Values in [ ~ ] show the minimum to maximum range.
Model
kW
kW
kW
A
%
kW
A
%
A
Poweful mode Hi:48 Me:45 Lo:42
dB(A)
Mild mode Hi:45 Me:42 Lo:39
mm
kg
Slitted fin & inner grooved tubing
kg
r
W
Powerful mode Hi:14 Me:13 Lo:11
CMM
Mild mode Hi:13 Me:11 Lo:10
W
Wireless remote control switch (Optional : RCN-E1R)
Wired remote control switch (Optional : RC-E1R)
Internal thermostat for fan motor.
mm
(in)
Connectable with VP16 (I.D. 16mm, O.D. 22mm)
Indoor air temperature
Item
DB
27˚C
20˚C
FDKNVA251HEN1R
FDKNA251R
5.6 [2.8~6.0]
6.3 [3.1~7.1]
1 Phase, 220–240V 50Hz/220V 60Hz
298 × 840 × 240
12
–
–
–
–
–
Microcomputer controlled de-icer
Tangential fan × 1
33 × 1
Direct line start
Unavailable
Plastic net (washable) × 2
Rubber sleeve (for fan motor)
–
Thermostat by electronics
Frost protection thermostat.
Liquid line: φ6.35 (1/4") Gas line: φ15.88 (5/8")
Flare piping
Necessary (both Liquid & Gas lines)
Mounting kit. Drain hose
Outdoor air temperature
WB DB
19˚C 35˚C
– 7˚C
82
- -
FDCVA251HENR
1.99/1.99
8.9/9.3
97/97
1.85/1.85
8.2/8.6
98/98
5
48
595 × 780 (+67) × 290
40
5CS102XFD × 1
Direct line start
Straight fin & inner grooved tubing
Electronic expansion valve
R410A
1.75 [Pre-charged up to the piping length of 30m]
0.48 (RB68A)
Propeller fan × 1
34 × 1
Direct line start
41
–
–
Rubber mount (for compressor)
20 (Crank case heater)
– (Indoor unit side)
–
Internal thermostat for fan motor.
Anomalous discharge temperature protection.
–
–
WB
24˚C
6˚C
Standards
ISO-T1