Appendix; Blower Installation; Optional Blower - Jøtul F50 TL Rangeley Installation And Operating Instructions Manual

139262 Rev_A 11/1/2010

7.0 Appendix

7.1 Optional Blower 156431

Tools Required
• 10 mm wrench or socket driver
• 1/4" socket driver or flat head screwdriver
• 4 mm hex key
• work gloves
CAUTION:
Avoid injury- always wear work gloves when handling sheet
metal parts. Read through these instructions to familiarize
yourself with these parts before beginning the installation.
 115 VAC, 60 HTZ, Max. 40 W
 This blower must be electrically grounded in
accordance with local codes or, in the absence
of local codes, with the current ANSI/NFPA 70,
National Electrical Code or CSA C22.1-Canadian
Electrical Code.
 This unit is supplied with a three-prong
(grounding) plug for protection against shock
hazard and should be plugged directly into
a properly grounded three-prong receptacle.
DO NOT CUT OR REMOVE THE GROUNDING
PRONG FROM THE PLUG.
 Do not connect to power supply until all
electical connections have been made.
 Always disconnect the power supply when
performing any service.
Installation
Install the blower kit before moving the stove into its final
position. If the stove is already installed, you may need to
pull it out to install this blower.
For Freestanding stove installations, where access to
the back of the stove is unrestricted, the Control Box may be
mounted to either corner of the rear shroud.
For Alcove or Hearthmount installations into fireplaces,
the Switch Box must be mounted under the stove, attached
to the side of the bottom heat shield. Determine the loca-
tion most appropriate to your needs and follow the installa-
tion steps outlined below.
1. Remove the Rear Shroud:
Use the 4 mm hex key to remove the socket head screws and
nuts at the bottom of each side of the Rear Shroud.
See fig. 20, A.
Loosen the two hex nuts at the upper rear of the stove and lift
the shroud up off of the stove. See fig. 20, B. Keep all shroud
fasteners for reassembly.
20
2. Attach the Air Deflector:
Bend the deflector tabs at the perforation lines as shown in
fig. 20. Attach the deflector to the interior side of the rear
shroud using two #8 X 12 sheet metal screws.
3. Attach the Blower Mounting Bracket to the two center studs
on the back of the stove, oriented as shown in fig. 20, using
two M6 hex nuts.
4. Attach the Blower to the Mounting Bracket using the two
wing nuts.
5. Attach the Snapstat Bracket to the lower stud on the back of
the stove, oriented as shown. Slide the Snapstat into place
betweeen the stove tnand the bracket. Connect the
6. Snapstat Installation:
Attach the Snapstat Bracket to the lower stud on the back of
the stove, oriented as shown. Slide the Snapstat into place
betweeen the stove and the bracket.
Connect either snapstat lead to either snapstat terminal.
7. Bend back the lower air deflector on the rear shroud and
reinstall it using the fasteners previously removed. Reverse the
procedure of Step 1.
8. Install the Control Box: The control box may be mounted to the
side of the stove closest to the nearest electrical outlet.
Freestanding Installation-
Attach the control box to either side of the rear shroud using a
1/4" socket driver and one #8 x 12 sheet metal screw as shown
in fig. 20.
Alcove or Hearthmount Installation -
Attach the Control Box Mounting Bracket to the back of the
Control Box using two #8 x 12 sheet metal screws.
Attach the Mounting Bracket/Control Box assembly to the
side of the Bottom Heat Shield using four #8 x 12 sheet metal
screws.
8. Route the power cord to the nearest electrical outlet.