Setting The Clock; Using Immediate-Start Function - Silvercrest DGS 800 Operation And Safety Notes

ries and / or damage of the appliance.
Now place the steam trays
1 - 2 - 3 succession (please see the markings on
the handles) on top of the condensate collec-
tion basin 7 .
Place the cover centrically so that the upper
1
steam tray is completely closed and no
3
steam can exhaust.
Connect the mains plug
In the LCD-display, the time indicator
appear (see fig. A).
Now your steamer is ready for use.

Setting the clock

Proceed as follows:
Simultaneously press the PROG
ON / OFF buttons for 2 - 3 seconds. A sig-
14
nal tone will be heard on releasing the buttons.
Press the PLUS button
indicator by 10 minutes each time. Press the
MINUS button 16 to reduce the time indicator
20 by 1 minute each time.
Press the PROG button
The LCD-display 13 will now show the current
clock time (clock time mode).

Using Immediate-Start Function

Note: Consider that the base of the appliance /
water tank has to be filled with water at least
10
up to the MIN mark . Ensure that the turbo ring
9
in addition to the condensate collection basin
has been correctly positioned.
Press the ON / OFF button
play will show the factory-set steaming time
13
of 45 minutes (see fig. B).
Note: If you do not press any button within
5 seconds you will hear a signal tone, the pilot
lamp 15 will glow red and the appliance will
start the steaming process automatically.
Press the PLUS / MINUS button
or reduce the steaming time in 5 minute steps.
Note: The maximum steaming time is 90 minutes.
3 , 4 , 6 in
to a suitable socket.
18
20 will
17 and
16 to increase the time
to confirm your setting.
17
8
7
14 . The LCD dis-
to increase
16
Note: Be aware that you might have to replen-
ish water when the steaming time is longer.
Use the openings on the sides of the conden-
sate collection basin for refilling. If the base
7
of the appliance / water tank
the MAX mark , it will be sufficient for approx.
19
1 hour of steaming.
ATTENTION! HAZARD OF BURNS!
Make sure that the water does not exceed the
MAX mark 19 . Otherwise, hot water may spurt
out of the steamer during operation.
5 seconds after the last button has been pressed
a signal tone will be heard. The pilot lamp
will glow red and the appliance will start the
steaming process automatically.
The LCD-display 13 will indicate the remaining
steaming time.
ATTENTION! HAZARD OF BURNS! The
appliance will become hot during use. Beware
of getting in contact with the ascending steam
or any components.
If the set steaming time is elapsed, the appli- If the set steaming time is elapsed, the appli-
ance will automatically switch back to the
keep-warm mode (see "keep-warm mode").
Note: During the steaming process, the steam-
ing time can be increased or reduced in 5
minute steps at any time by pressing the
PLUS / MINUS button . If the steaming time
16
is manually reduced to '0', the appliance will
switch over to keep-warm mode (see "keep-
warm mode") automatically.
ATTENTION! HAZARD OF BURNS!
Always lift the cover 1 slowly, turning away
from you and let the steam exhaust backwards.
Do not bend over the appliance during steam
generation. Use oven cloths when touching the
cover and the steam trays
1
a long fork or tongs when checking if the food
is done.
Press the ON / OFF button
steaming process prematurely or to switch off
the appliance. The indicator on the LCD-display
switches back to the time indicator
13
again (see fig. A).
Note: If the supply of water is used up during
use, a signal tone will sound. The steaming
process gets stopped. The indicator on the
LCD-display switches back to the time indi-
13
Initial Operation
10 is filled up to
15
, , . Use
3 4 6
to terminate the
14
20
GB/IE/CY 9