Page 1 TL-SL5428E JetStream L2 Managed Switch Rev: 1.1.1 1910010457...
Page 2 Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
Page 3: Table Of Contents
CONTENTS Preface ......................1 Chapter 1 Using the CLI ..................4 1.1 Accessing the CLI ......................4 1.1.1 Logon by a console port ..................4 1.1.2 Logon by Telnet ....................6 1.2 CLI Command Modes .....................8 1.3 Security Levels ......................11 1.4 Conventions ........................11 1.4.1 Format Conventions ...................
Page 4 mac-vlan interface .........................22 show mac-vlan ........................23 show mac-vlan interface......................23 Chapter 5 Protocol VLAN Commands............... 24 protocol-vlan template ......................24 protocol-vlan vlan ........................24 protocol-vlan interface ......................25 show protocol-vlan template....................26 show protocol-vlan vlan ......................26 show protocol-vlan interface....................26 Chapter 6 VLAN-VPN Commands..............28 vlan-vpn enable ........................28 vlan-vpn tpid ..........................28 vlan-vpn vlan-mapping add ....................29 vlan-vpn vlan-mapping modify....................29...
Page 5 show private-vlan ........................40 show private-vlan switchport ....................40 Chapter 9 GVRP Commands................42 gvrp ............................42 gvrp (interface) ........................42 gvrp registration........................43 gvrp timer ..........................43 show gvrp global ........................44 show gvrp interface .......................45 Chapter 10 LAG Commands ................46 interface link-aggregation ......................46 interface range link-aggregation ....................46 link-aggregation........................47 link-aggregation hash-algorithm ....................48 description ..........................48...
Page 6 user idle-timeout........................59 show user account-list ......................60 show user configuration......................60 Chapter 13 Binging Table Commands..............62 binding-table user-bind ......................62 binding-table remove ......................63 dhcp-snooping........................63 dhcp-snooping global ......................64 dhcp-snooping information enable ..................65 dhcp-snooping information strategy ..................65 dhcp-snooping information user-defined ................66 dhcp-snooping information remote-id ..................66 dhcp-snooping information circuit-id..................67 dhcp-snooping trusted ......................67 dhcp-snooping mac-verify .....................68...
Page 7 dos-prevent ...........................79 dos-prevent global .........................79 dos-prevent type........................80 dos-prevent detect.........................81 show dos-prevent reset ......................81 show dos-prevent ........................82 Chapter 17 IEEE 802.1X Commands ..............83 dot1x............................83 dot1x authentication-method ....................83 dot1x guest-vlan ........................84 dot1x quiet-period........................85 dot1x timer..........................85 dot1x retry ..........................86 dot1x............................86 dot1x guest-vlan ........................87 dot1x port-control ........................87 dot1x port-method .........................88 radius authentication primary-ip ....................89...
Page 8 show logging local-config ....................100 show logging loghost ......................100 show logging buffer ......................101 show logging flash.......................101 Chapter 19 SSH Commands................103 ssh server enable ........................103 ssh version ..........................103 ssh idle-timeout ........................104 ssh max-client ........................104 ssh download ........................105 show ssh ..........................105 Chapter 20 SSL Commands ................107 ssl enable ..........................107 ssl download certificate .......................107 ssl download key .........................108...
Page 9 user-config backup ......................120 user-config load........................120 user-config save ........................121 firmware upgrade ........................121 ping .............................122 tracert ..........................122 loopback ..........................123 show system-info.........................123 show ip address ........................124 show system-time........................124 show system-time dst ......................125 Chapter 23 Ethernet Configuration Commands ..........126 interface ethernet ........................126 interface range ethernet ......................126 description ...........................127 shutdown ..........................127 flow-control ..........................128...
Page 10 qos scheduler ........................139 show qos port-based ......................140 show qos dot1p ........................141 show qos dscp........................141 show qos scheduler......................141 Chapter 25 Port Mirror Commands ..............143 port mirror..........................143 port mirrored........................143 show port mirror ........................144 Chapter 26 Port isolation Commands ..............145 port isolation ........................145 show port isolation.......................145 Chapter 27 ACL Commands................147 acl time-segment .........................147...
Page 11 spanning-tree msti .......................165 spanning-tree tc-defend.......................166 spanning-tree security ......................166 spanning-tree mcheck ......................167 show spanning-tree global-info....................168 show spanning-tree global-config ..................168 show spanning-tree port-config ...................168 show spanning-tree region ....................169 show spanning-tree msti config ...................169 show spanning-tree msti port ....................170 show spanning-tree security tc-defend ................170 show spanning-tree security port-defend................171 Chapter 29 IGMP Commands................172 Igmp-snooping global ......................172...
Page 12 snmp community-add ......................188 snmp notify-add........................189 snmp-rmon history sample-cfg ....................190 snmp-rmon history owner ....................191 snmp-rmon history enable ....................191 snmp-rmon event user......................192 snmp-rmon event description ....................193 snmp-rmon event type......................193 snmp-rmon event owner......................194 snmp-rmon event enable.....................194 snmp-rmon alarm config......................195 snmp-rmon alarm owner......................196 snmp-rmon alarm enable.....................197 show snmp global-config .....................197 show snmp view ........................198 show snmp group ........................198...
Page 13 show cluster manage config ....................209 show cluster manage member ....................210 show cluster manage role....................210...
Page 14: Preface
JetStream L2 Managed Switch CLI Guide Preface This Guide is intended for network administrator to provide referenced information about CLI (Command Line Interface). The device mentioned in this Guide stands for TL-SL5428E JetStream L2 Managed Switch. Overview of this Guide...
Page 15 TL-SL5428E JetStream L2 Managed Switch CLI Guide Chapter 12: User Manage Commands Provide information about the commands used for user management. Chapter 13: Binding Table Commands Provide information about the commands used for binding the IP address, MAC address, VLAN and the connected Port number of the Host together.
Page 16 TL-SL5428E JetStream L2 Managed Switch CLI Guide Provide information about the commands used for configuring the Port Mirror function. Chapter 26: Port isolation Commands Provide information about the commands used for configuring the Port isolation function. Chapter 27: ACL Commands Provide information about the commands used for configuring the ACL (Access Control List).
Page 17: Chapter 1 Using The Cli
TL-SL5428E JetStream L2 Managed Switch CLI Guide Chapter 1 Using the CLI 1.1 Accessing the CLI You can log on to the switch and access the CLI by the following two methods: Log on to the switch by the console port on the switch.
Page 18 TL-SL5428E JetStream L2 Managed Switch CLI Guide Figure 1-2 Connection Description Select the port to connect in figure 1-3, and click OK. Figure 1-3 Select the port to connect Configure the port selected in the step above as the following figure1-4 shown. Configure Bits per second as 38400, Data bits as 8, Parity as None, Stop bits as 1, Flow control as None, and then click OK.
Page 19: 1.1.2 Logon By Telnet
Type the User name and Password in the Hyper Terminal window, the factory default value for both of them is admin. The DOS prompt” TP-LINK>” will appear after pressing the Enter button as figure1-5 shown. It indicates that you can use the CLI now.
Page 20 TL-SL5428E JetStream L2 Managed Switch CLI Guide Figure 1-6 Open the Run window Type cmd in the prompt Run window as figure 1-7 and click OK. Figure 1-7 Run Window Type telnet 192.168.0.1 in the command prompt shown as figure1-8, and press the Enter...
Page 21: 1.2 Cli Command Modes
TL-SL5428E JetStream L2 Managed Switch CLI Guide Figure 1-8 Connecting to the Switch Type the User name and Password (the factory default value for both of them is admin) and press the Enter button, then you can use the CLI now, which is shown as figure1-9.
Page 22 TL-SL5428E JetStream L2 Managed Switch CLI Guide The following table gives detailed information about the Accessing path, Prompt of each mode and how to exit the current mode and access the next mode. Accessing Logout or Access the next Mode...
Page 23 TL-SL5428E JetStream L2 Managed Switch CLI Guide Use the interface type Use the end command or press Ctrl+Z number command to to return to Privileged EXEC mode. Interface enter this mode from TP-LINK(config-if Enter exit command to return to Global...
Page 24: 1.3 Security Levels
TL-SL5428E JetStream L2 Managed Switch CLI Guide history: Display the commands history. 1.3 Security Levels This switch’s security is divided into two levels: User level and Admin level. User level only allows users to do some simple operations in User EXEC Mode; Admin level allows you to monitor, configure and manage the switch in Privileged EXEC Mode, Global Configuration Mode, Interface Configuration Mode and VLAN Configuration Mode.
Page 25: 1.4.3 Parameter Format
TL-SL5428E JetStream L2 Managed Switch CLI Guide If a blank is contained in a character string, single or double quotation marks should be used, for example ’hello world’, ”hello world”, and the words in the quotation marks will be identified as a string.
Page 26: Chapter 2 User Interface
—— super password ， which contains 16 characters at most, composing digits, English letters and underdashes only. By default, it is empty. Command Mode Global Configuration Mode Example Set the super password as admin to access Privileged EXEC Mode from User EXEC Mode: TP-LINK(config)# enable password admin...
Page 27: Disable
TL-SL5428E JetStream L2 Managed Switch CLI Guide disable Description The disable command is used to return to User EXEC Mode from Privileged EXEC Mode. Syntax disable Command Mode Privileged EXEC Mode Example Return to User EXEC Mode from Privileged EXEC Mode: TP-LINK# disable TP-LINK>...
Page 28: End
TL-SL5428E JetStream L2 Managed Switch CLI Guide exit Command Mode Any Configuration Mode Example Return to Global Configuration Mode from Interface Configuration Mode, and then return to Privileged EXEC Mode: TP-LINK(config-if)# exit TP-LINK(config)#exit TP-LINK# Description The end command is used to return to Privileged EXEC Mode.
Page 29: Chapter 3 Ieee 802.1Q Vlan Commands
Syntax vlan database Command Mode Global Configuration Mode Example Access VLAN Configuration Mode: TP-LINK(config)# vlan database TP-LINK(config-vlan)# vlan Description The vlan command is used to create IEEE 802.1Q VLAN. To delete the IEEE 802.1Q VLAN, please use no vlan command.
Page 30: Interface Vlan
——VLAN ID, ranging from 1 to 4094. Command Mode Global Configuration Mode Example Configure the VLAN2: TP-LINK(config)# interface vlan 2 description Description The description command is used to assign a description string to a VLAN. To clear the description, please use no description command.
Page 31: Switchport Type
TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK(config)# interface vlan 2 TP-LINK(config-if)#description vlan2 switchport type Description The switchport type command is used to configure the Link Types for the ports. Syntax switchport type { access | trunk | general } Parameter access | trunk | general ——...
Page 32: Switchport Pvid
TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# switchport allowed vlan add 2 switchport pvid Description The switchport pvid command is used to configure the PVID for the switch ports. Syntax switchport pvid vlan-id Parameter vlan-id —— VLAN ID, ranging from 1 to 4094.
Page 33: Show Vlan
TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# switchport general egress-rule 3 tagged show vlan Description The show vlan command is used to display the information of IEEE 802.1Q VLAN . Syntax show vlan [vlan-id] Parameter vlan-id ——...
Page 34: Chapter 4 Mac Vlan Commands
, it is empty. Command Mode Global Configuration Mode Example Create VLAN 2 named “RD”, and the MAC address is 00:00:00:00:00:01: TP-LINK(config)# mac-vlan add 2 00:00:00:00:00:01 RD mac-vlan remove Description The mac-vlan remove command is used to delete the subsistent MAC-Based VLAN entry.
Page 35: Mac-Vlan Modify
Example Modify the VLAN ID of the MAC VLAN entry with the MAC address of 00:00:00:00:00:02 as 12: TP-LINK(config)# mac-vlan modify 12 00:00:00:00:00:02 mac-vlan interface Description The mac-vlan interface command is used to enable the port for the MAC VLAN feature.
Page 36: Show Mac-Vlan
JetStream L2 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Enable the ports 1-3,11-15 for the MAC VLAN feature: TP-LINK(config)# mac-vlan interface 1-3,11-15 show mac-vlan Description The show mac-vlan command is used to display the information of the MAC VLAN entry .
Page 37: Chapter 5 Protocol Vlan Commands
Global Configuration Mode Example Create a Protocol VLAN template named “arp” whose Ethernet protocol type is 0806 and delete the Protocol template whose number is 2: TP-LINK(config)# protocol-vlan template add arp 0806 TP-LINK(config)# protocol-vlan template remove 2 protocol-vlan vlan Description The protocol-vlan vlan command is used to create a Protocol VLAN entry.
Page 38: Protocol-Vlan Interface
Global Configuration Mode Example Create a Protocol VLAN entry, whose index is 1 and vid is 2. And then delete the Protocol VLAN entry whose number is 1: TP-LINK(config)# protocol-vlan vlan 2 template 1 TP-LINK(config)# no protocol-vlan vlan 1 protocol-vlan interface Description The protocol-vlan interface command is used to enable the Protocol VLAN feature for a specified port.
Page 39: Show Protocol-Vlan Template
Command Mode Any Configuration Mode Example Display the information of the Protocol VLAN templates: TP-LINK(config)# show protocol-vlan template show protocol-vlan vlan Description The show protocol-vlan vlan command is used to display the information about Protocol VLAN entry.
Page 40 TL-SL5428E JetStream L2 Managed Switch CLI Guide Any Configuration Mode Example Display the configuration of the protocol-vlan interface: TP-LINK(config)# show protocol-vlan interface...
Page 41: Chapter 6 Vlan-Vpn Commands
Command Mode Global Configuration Mode Example Enable the VLAN-VPN function globally: TP-LINK(config)# vlan-vpn enable vlan-vpn tpid Description The vlan-vpn tpid command is used to configure Global TPID of the VLAN-VPN. To restore to the default value, please use the no vlan-vpn tpid command.
Page 42: Vlan-Vpn Vlan-Mapping Add
Global Configuration Mode Example Add a VLAN Mapping entry with the C-VLAN being 2 and the SP-VLAN being 200: TP-LINK(config)# vlan-vpn vlan-mapping add 2 200 vlan-vpn vlan-mapping modify Description The vlan-vpn vlan-mapping modify command is used to modify the subsistent...
Page 43: Vlan-Vpn Vlan-Mapping Remove
Global Configuration Mode Example Modify the subsistent VLAN Mapping entry with the C-VLAN 2,and reconfigure the SP-VLAN as 100: TP-LINK(config)# vlan-vpn vlan-mapping modify 2 100 vlan-vpn vlan-mapping remove Description The vlan-vpn vlan-mapping remove command is used to delete the subsistent VLAN Mapping entry according to the C-VLAN ID.
Page 44: Vlan-Vpn Uplink
Command Mode Global Configuration Mode Example Enable the VLAN Mapping feature for the ports 2-5,16-18: TP-LINK(config)# vlan-vpn vlan-mapping interface 2-5,16-18 vlan-vpn uplink Description The vlan-vpn uplink command is used to configure a specified port as the VPN Up-link port. To cancel this VPN Up-link port, please use the no vlan-vpn uplink command.
Page 45: Show Vlan-Vpn Uplink
Command Mode Any Configuration Mode Example Display the global configuration information of the VLAN VPN: TP-LINK(config)# show vlan-vpn global show vlan-vpn uplink Description The show vlan-vpn uplink command is used to display the configuration information of the VLAN VPN Up-link ports.
Page 46: Show Vlan-Vpn Vlan-Mapping Interface
The show vlan-vpn vlan-mapping interface command is used to display the VLAN Mapping port enable state. port state of VLAN Mapping Syntax show vlan-vpn vlan-mapping interface Command Mode Any Configuration Mode Example Display the VLAN Mapping port enable state: TP-LINK(config)# show vlan-vpn vlan-mapping interface...
Page 47: Chapter 7 Voice Vlan Commands
Command Mode Global Configuration Mode Example Enable the Voice VLAN function for VLAN 2: TP-LINK(config)# voice-vlan enable 2 voice-vlan aging-time Description The voice-vlan aging-time command is used to set the aging time for a voice VLAN. To restore to the default aging time for the Voice VLAN, please use no voice-vlan aging-time command.
Page 48: Voice-Vlan Priority
Command Mode Global Configuration Mode Example Set the aging time for the Voice VLAN as 2880 minutes: TP-LINK(config)# voice-vlan aging-time 2880 voice-vlan priority Description The voice-vlan priority command is used to configure the priority for the Voice VLAN. To restore to the default priority, please use no voice-vlan priority command.
Page 49: Switchport Voice-Vlan Mode
By default, it is empty. Command Mode Global Configuration Mode Example Create a Voice VLAN OUI descripted as TP-LINK Phone with the MAC address 00:01:E3:00:00:01 and the mask address FF:FF:FF:00:00:00. And then delete the Voice VLAN OUI with the MAC address 00:00:00:11:00:01: 00:01:E3:00:00:01...
Page 50: Switchport Voice-Vlan Security
TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK(config-if)# switchport voice-vlan mode manual switchport voice-vlan security Description The switchport voice-vlan security command is used to configure the Voice VLAN security mode. Syntax switchport voice-vlan security {disable | enable} Parameter disable / enable —— disable/enable the security mode for the specified port .
Page 51: Show Voice-Vlan Oui
Command Mode Any Configuration Mode Example Display the configuration information of Voice VLAN OUI: TP-LINK(config)# show voice-vlan oui show voice-vlan switchport Description The show voice-vlan switchport command is used to displays the configuration information of the port in the Voice VLAN.
Page 52: Chapter 8 Private Vlan Commands
Global Configuration Mode Example Create the Private VLAN as VLAN15 for primary VLAN and VLAN150 for secondary VLAN: TP-LINK(config)# private-vlan primary 15 secondary 150 switchport private-vlan Description The switchport private-vlan command is used to configure the private VLAN mode for the switchport. To remove the port from Private VLAN, please use no switchport private-vlan command.
Page 53: Show Private-Vlan
Add promiscuous port10 in Private VLAN as VLAN15 for primary VLAN and VLAN150 for secondary VLAN: TP-LINK(config)# interface ethernet 10 TP-LINK(config-if)# switchport private-vlan promiscuous 15 150 show private-vlan Description The show private-vlan command is used to display the Private VLAN configured on the switch.
Page 54 TL-SL5428E JetStream L2 Managed Switch CLI Guide show private-vlan switchport [port-num] Command Mode Any Configuration Mode Example Display the configuration information of all the ports in the Private VLAN: TP-LINK(config)# show private-vlan switchport...
Page 55: Chapter 9 Gvrp Commands
TL-SL5428E JetStream L2 Managed Switch CLI Guide Chapter 9 GVRP Commands GVRP (GARP VLAN registration protocol) is an implementation of GARP (generic attribute registration protocol). GVRP allows the switch to automatically add or remove the VLANs via the dynamic VLAN registration information and propagate the local VLAN registration information to other switches, without having to individually configure each VLAN.
Page 56: Gvrp Registration
TL-SL5428E JetStream L2 Managed Switch CLI Guide Example Enable the GVRP function for ports 2-6: TP-LINK(config)# interface range ethernet 2-6 TP-LINK(config-if)# gvrp gvrp registration Description The gvrp registration command is used to configure the GVRP registration type on the desired port. To restore to the default value, please use no gvrp registration command.
Page 57: Show Gvrp Global
Set the GARP leaveall timer of port 6 to 2000 centiseconds and restore to the join timer of it to the default value: TP-LINK(config)# interface ethernet 6 TP-LINK(config-if)# gvrp timer leaveall 2000 TP-LINK(config-if)# no gvrp timer join show gvrp global Description The show gvrp global command is used to to display the global GVRP status.
Page 58: Show Gvrp Interface
TL-SL5428E JetStream L2 Managed Switch CLI Guide Example Display the global GVRP status: TP-LINK(config)# show gvrp global show gvrp interface Description The show gvrp interface command is used to display the GVRP configuration information of the specified Ethernet ports. Syntax...
Page 59: Chapter 10 Lag Commands
Command Mode Global Configuration Mode Example Access the Interface Link-aggregation Mode and configure the aggregation group 1: TP-LINK(config)# interface link-aggregation 1 TP-LINK(config-if)# interface range link-aggregation Description The interface range link-aggregation command is used to access the Interface range Link-aggregation Mode, and you can configure some aggregation groups at the same time.
Page 60: Link-Aggregation
——The aggregation group list. You can configure some aggregation groups at the same time. Example Access the Interface range Link-aggregation Mode and configure the aggregation group 1,4-6: TP-LINK(config)# interface range link-aggregation 1,4-6 TP-LINK(config-if)# link-aggregation Description The link-aggregation command is used to add the current Ethernet port to an aggregation group.
Page 61: Link-Aggregation Hash-Algorithm
Command Mode Global Configuration Mode Example Configure the Aggregate Arithmetic for LAG as src_dst_mac: TP-LINK(config)# link-aggregation hash-algorithm src_dst_mac description Description The description command is used to set a description for an aggregation group. To remove the description of an aggregation group, please use no description command.
Page 62: Show Interface Link-Aggregation
TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK(config)# interface link-aggregation 1 TP-LINK(config-if)# description “movie server” show interface link-aggregation Description The show interface link-aggregation command is used to display the configuration information of the Aggregate Arithmetic and the aggregation groups. Syntax...
Page 63: Chapter 11 Lacp Commands
TL-SL5428E JetStream L2 Managed Switch CLI Guide Chapter 11 LACP Commands LACP (Link Aggregation Control Protocol) is defined in IEEE802.3ad and enables the dynamic link aggregation and disaggregation by exchanging LACP packets with its partner. The switch can dynamically group similarly configured ports into a single logical link, which will highly extend the bandwidth and flexibly balance the load.
Page 64: Lacp Admin-Key
TL-SL5428E JetStream L2 Managed Switch CLI Guide Example Enable LACP protocol on the port 1: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# lacp lacp admin-key Description The lacp admin-key command is used to configure the admin key. To restore to the default value, please use no lacp admin-key command.
Page 65: Lacp Port-Priority
Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Set the system priority of port 1 to1024: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# lacp system-priority 1024 lacp port-priority Description The lacp port-priority command is used to set the priority of the current port. To restore to the default priority, please use no lacp port-priority command.
Page 66: Show Lacp Interface
[ethernet port-num] Parameter port-num —— The Ethernet port number. By default, display the configuration information of all the Ethernet ports. Command Mode Any Configuration Mode Example Display the configuration information of all the Ethernet ports: TP-LINK(config)# show lacp interface...
Page 67: Chapter 12 User Manage Commands
Admin: can edit, modify and view all the settings of different functions. disable | enable ——Enable/disable the user. Command Mode Global Configuration Mode Example Add and enable a new admin user named tplink, and of which the password is password: TP-LINK(config)#user add tplink password password confirm-password password admin enable...
Page 68: User Remove
Syntax user modify status user-name {disable | enable} Parameter user-name —— The existing user name. disable | enable ——Disable/enable the user. Command Mode Global Configuration Mode Example Change the status of tplink to enabled: TP-LINK(config)# user modify status tplink enable...
Page 69: User Modify Type
| admin —— Access level. Guest: limited user; admin: manager. Command Mode Global Configuration Mode Example Change the access level of tplink to admin: TP-LINK(config)# user modify type tplink admin user modify password Description The user modify password command is used to modify the password for the existing user.
Page 70: User Access-Control Disable
JetStream L2 Managed Switch CLI Guide Global Configuration Mode Example Modify the password of tplink as newpwd: TP-LINK(config)# user modify password tplink password newpwd newpwd user access-control disable Description The user access-control disable command is used to cancel the user access-control.
Page 71: User Access-Control Mac-Based
00:00:13:0A:00:01: TP-LINK(config)# user access-control mac-based 00:00:13:0A:00:01 user access-control port-based Description The user access-control port-based command is used to limit the ports for login. Only the users connected to these ports you set here are allowed for login.
Page 72: User Max-Number
Command Mode Global Configuration Mode Example Enable the access-control of the ports 2, port4, port5, port6,and port10: TP-LINK(config)# user access-control port-based 2,4-6,10 user max-number Description The user max-number command is used to configure the number of the users logging on at the same time. To cancel the limit to the numbers of the users logging in, please use no user max-number command.
Page 73: Show User Account-List
10. Command Mode Global Configuration Mode Example Configure the timeout time of the switch as 15 minutes: TP-LINK(config)# user idle-timeout 15 show user account-list Description The show user account-list command is used to display the information of the current users.
Page 74 TL-SL5428E JetStream L2 Managed Switch CLI Guide information of the users, including access-control, max-number and the idle-timeout, etc. Syntax show user configuration Command Mode Any Configuration Mode Example Display the security configuration information of the users: TP-LINK(config)# show user configuration...
Page 75: Chapter 13 Binging Table Commands
TL-SL5428E JetStream L2 Managed Switch CLI Guide Chapter 13 Binging Table Commands You can bind the IP address, MAC address, VLAN and the connected Port number of the Host together, which can be the condition for the ARP Inspection and IP Source Guard to filter the packets.
Page 76: Binding-Table Remove
Command Mode Global Configuration Mode Example Delete the IP-MAC –VID-PORT entry with the index 5: TP-LINK(config)# binding-table remove index 5 dhcp-snooping Description The dhcp-snooping command is used to enable the DHCP-snooping function for the switch. To disable the DHCP-snooping function, please use no dhcp-snooping command.
Page 77: Dhcp-Snooping Global
TL-SL5428E JetStream L2 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Enable the DHCP-snooping function globally: TP-LINK(config)# dhcp-snooping dhcp-snooping global Description The dhcp-snooping global command is used to configure the DHCP snooping globally. To restore to the default value, please use no dhcp-snooping global command.
Page 78: Dhcp-Snooping Information Enable
TL-SL5428E JetStream L2 Managed Switch CLI Guide and decline Flow Control as 20 pps for DHCP Snooping TP-LINK(config)# dhcp-snooping global global-rate 30 dec-threshold 20 dec-rate 20 dhcp-snooping information enable Description The dhcp-snooping information enable command is used to enable the Option 82 function of DHCP Snooping.
Page 79: Dhcp-Snooping Information User-Defined
Global Configuration Mode Example Replace the Option 82 field of the packets with the switch defined one and then send out: TP-LINK(config)# dhcp-snooping information strategy replace dhcp-snooping information user-defined Description The dhcp-snooping information user-defined command is used to permit users to define the Option 82. To disable the function, please use no dhcp-snooping information user-defined command.
Page 80: Dhcp-Snooping Information Circuit-Id
Command Mode Global Configuration Mode Example Configure the sub-option Remote ID for the customized Option 82 as tplink: TP-LINK(config)# dhcp-snooping information remote-id tplink dhcp-snooping information circuit-id Description The dhcp-snooping information circuit-id command is used to configure the sub-option Circuit ID for the customized Option 82.
Page 81: Dhcp-Snooping Mac-Verify
Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Configure the port 2 to be a Trusted Port: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# dhcp-snooping trusted dhcp-snooping mac-verify Description The dhcp-snooping mac-verify command is used to enable the MAC Verify feature.
Page 82: Dhcp-Snooping Decline
Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Set the Flow Control of port 2 as 20 pps: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# dhcp-snooping rate-limit 20 dhcp-snooping decline Description The dhcp-snooping decline command is used to enable the Decline Protect feature.
Page 83: Show Binding-Table
Command Mode Any Configuration Mode Example Display the configuration of DHCP Snooping globally: TP-LINK(config)# show dhcp-snooping global show dhcp-snooping information Description The show dhcp-snooping information command is used to display the Option 82 configuration of DHCP Snooping.
Page 84: Show Dhcp-Snooping Interface
Command Mode Any Configuration Mode Example Display the Option 82 configuration of DHCP Snooping: TP-LINK(config)# show dhcp-snooping information show dhcp-snooping interface Description The show dhcp-snooping interface command is used to display the interface configuration of DHCP Snooping.
Page 85: Chapter 14 Arp Inspection Commands
Command Mode Global Configuration Mode Example Enable the ARP Detection function globally: TP-LINK(config)# arp detection arp detection trust-port Description The arp detection trust-port command is used to configure the port for which the ARP Detect function is unnecessary as the Trusted Port. To clear the Trusted Port list, please use no arp detection trust-port command .The...
Page 86: Arp Detection (Interface)
Command Mode Global Configuration Mode Example Configure the ports 2-5,11-15 as the Trusted Port: TP-LINK(config)# arp detection trust-port 2-5,11-15 arp detection (interface) Description The arp detection (interface) command is used to enable the ARP Defend function. To disable the arp detection function, please use no arp detection command.
Page 87: Arp Detection Recover
Configure the maximum amount of the received ARP packets per second as 50 pps for the port 5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# arp detection limit-rate 50 arp detection recover Description The arp detection recover command is used to restore to the port to the ARP transmit status from the ARP filter status.
Page 88: Show Arp Detection Global
Command Mode Any Configuration Mode Example Display the ARP detection configuration globally: TP-LINK(config)# show arp detection global show arp detection interface Description The show arp detection interface command is used to display the interface configuration of ARP detection.
Page 89: Show Arp Detection Statistic
The show arp detection statistic reset command is used to clear the statistic of the illegal ARP packets received. Syntax show arp detection statistic reset Command Mode Global Configuration Mode Example Clear the statistic of the illegal ARP packets received: TP-LINK(config)# show arp detection statistic reset...
Page 90: Chapter 15 Ip Source Guard Commands
Enable the IP Source Guard function for the ports 5-10. Configure that only the packets with its source IP address, source MAC address and port number matched to the IP-MAC binding rules can be processed: TP-LINK(config)# interface range ethernet 5-10 TP-LINK(config-if)# ip source guard sip+mac...
Page 91: Show Ip Source Guard
Description The show ip source guard command is used to display the IP Source Guard configuration. Syntax show ip source guard Command Mode Any Configuration Mode Example Display the IP Source Guard configuration: TP-LINK(config)# show ip source guard...
Page 92: Chapter 16 Dos Defend Command
TL-SL5428E JetStream L2 Managed Switch CLI Guide Chapter 16 DoS Defend Command DoS (Denial of Service) Attack is to occupy the network bandwidth maliciously by the network attackers or the evil programs sending a lot of service requests to the Host. With the DoS Defend enabled, the switch can analyze the specific field of the received packets and provide the defend measures to ensure the normal working of the local network.
Page 93: Dos-Prevent Type
Global Configuration Mode Example Specify the transmission rate of the Ping packets and the SYN/SYN-ACK packets as 256K and 1m: TP-LINK(config)# dos-prevent global 256k 1m dos-prevent type Description The dos-prevent type command is used to select the DoS Defend Type. To disable the corresponding Defend Type, please use no dos-prevent type command.
Page 94: Dos-Prevent Detect
Global Configuration Mode Example Enable four DoS Defend Types named Land attack, Xma Scan attack, Smurf attack and Ping flooding attack: TP-LINK(config)# dos-prevent land xma-scan smurf ping-flood dos-prevent detect Description The dos-prevent detect command is used to detect the DoS attack. DoS Detect functions to detect the details of the DoS attack packets, based on which you can quickly locate the attacker in the local network.
Page 95: Show Dos-Prevent
Command Mode Global Configuration Mode Example Clear the information statistic of the detected DoS attack: TP-LINK(config)# show dos-prevent reset show dos-prevent Description The show dos-prevent command is used to display the DoS information of the detected DoS attack, including enable/disable status, the DoS Defend Type, the count of the attack,etc.
Page 96: Chapter 17 Ieee 802.1X Commands
TL-SL5428E JetStream L2 Managed Switch CLI Guide Chapter 17 IEEE 802.1X Commands IEEE 802.1X function is to provide an access control for LAN ports via the authentication. Only the supplicant passing the authentication can access the LAN. dot1x Description The dot1x command is used to enable the IEEE 802.1X function globally. To disable the IEEE 802.1X function, please use no dot1x command.
Page 97: Dot1X Guest-Vlan
Command Mode Global Configuration Mode Example Configure the Authentication Method of IEEE 802.1X as pap: TP-LINK(config)# dot1x authentication-method pap dot1x guest-vlan Description The dot1x guest-vlan command is used to enable the Guest VLAN function globally. To disable the Guest VLAN function, please use no dot1x guest-vlan command.
Page 98: Dot1X Quiet-Period
Command Mode Global Configuration Mode Example Enable the quiet-period function: TP-LINK(config)# dot1x quiet-period dot1x timer Description The dot1x timer command is used to configure the Quiet Period and the SupplicantTimeout. To restore to the default, please use no dot1x timer command.
Page 99: Dot1X Retry
Global Configuration Mode Example Configure the Quiet Period and the SupplicantTimeout as 12 seconds and 6 seconds: TP-LINK(config)# dot1x timer quiet-period 12 supp-timeout 6 dot1x retry Description The dot1x retry command is used to configure the maximum transfer times of the repeated authentication request.
Page 100: Dot1X Guest-Vlan
Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Enable the IEEE 802.1X function for the port 1: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# dot1x dot1x guest-vlan Description The dot1x guest-vlan command is used to enable the Guest VLAN function for a specified port.
Page 101: Dot1X Port-Method
Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Configure the Control Mode for port 1 as authorized-force: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# dot1x port-control authorized-force dot1x port-method Description The dot1x port-method command is used to configure the Control Type of IEEE 802.1X for the specified port.
Page 102: Radius Authentication Primary-Ip
User Service）server is used as the Authentication server generally. Syntax radius authentication primary-ip ip-addr Parameter ip-addr —— The IP address of the authentication server. Command Mode Global Configuration Mode Example Configure the IP of the authentication server as 10.20.1.100: TP-LINK(config)# radius authentication primary-ip 10.20.1.100...
Page 103: Radius Authentication Secondary-Ip
Command Mode Global Configuration Mode Example Configure the IP address of the alternate authentication server as 10.20.1.101: TP-LINK(config)# radius authentication secondary-ip 10.20.1.101 radius authentication port Description The radius authentication port command is used to configure the authentication port of the alternate authentication server. To restore to the default value, please use no radius authentication port command.
Page 104: Radius Authentication Key
JetStream L2 Managed Switch CLI Guide Global Configuration Mode Example Configure the authentication port of the alternate authentication server as 1815: TP-LINK(config)# radius authentication port 1815 radius authentication key Description The radius authentication key command is used to configure the shared password for the switch and the authentication servers to exchange messages.
Page 105: Radius Accounting Primary-Ip
Command Mode Global Configuration Mode Example Configure the IP address of the accounting server as 10.20.1.100: TP-LINK(config)# radius accounting primary-ip 10.20.1.100 radius accounting secondary-ip Description The radius accounting secondary-ip command is used to configure the IP address of the alternate accounting server. To restore to the default configuration, please use no radius accounting secondary-ip command.
Page 106: Radius Accounting Port
Command Mode Global Configuration Mode Example Configure the IP address of the alternate accounting server as 10.20.1.101: TP-LINK(config)# radius accounting secondary-ip 10.20.1.101 radius accounting port Description The radius accounting port command is used to set the UDP port of accounting server(s). To restore to the default value, please use no radius accounting port.
Page 107: Radius Response-Timeout
Global Configuration Mode Example Configure the shared password for the switch and the accounting servers as tplink: TP-LINK(config)# radius accounting key tplink radius response-timeout Description The radius response-timeout command is used to configure the maximum time for the switch to wait for the response from the RADIUS authentication and the accounting server.
Page 108: Show Dot1X Global
Example Configure the maximum time for the switch to wait for the response from the RADIUS authentication and the accounting server as 5 seconds: TP-LINK(config)# radius response-timeout 5 show dot1x global Description The show dot1x global command is used to display the global configuration of 801.X.
Page 109: Show Radius Authentication
TL-SL5428E JetStream L2 Managed Switch CLI Guide Example Display the port configuration of 801.X: TP-LINK(config)# show dot1x interface show radius authentication Description The show radius authentication command is used to display the configuration of the RADIUS authentication server. Syntax show radius authentication...
Page 110: Chapter 18 Log Commands
By default, it is 7 indicating that all the log information will be saved in the log buffer. disable | enable —— Disable or enable the log buffer. By default, it is enabled. Command Mode Global Configuration Mode Example Enable the log buffer function and set the severity as 6: TP-LINK(config)# logging local buffer 6 enable...
Page 111: Logging Local Flash
Command Mode Global Configuration Mode Example Enable the log file function and set the severity as 7: TP-LINK(config)# logging local flash 7 logging clear Description The logging clear command is used to clear the information in the log buffer and log file.
Page 112: Logging Loghost
Command Mode Global Configuration Mode Example Clear the information in the log file: TP-LINK(config)# logging clear buffer logging loghost Description The logging loghost command is used to configure the Log Host. To clear the configuration of the specified Log Host, please use no logging loghost command.
Page 113: Show Logging Local-Config
TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK(config)# logging loghost index 2 192.168.0.148 5 enable show logging local-config Description The show logging local-config command is used to display the configuration of the Local Log including the log buffer and the log file.
Page 114: Show Logging Buffer
Any Configuration Mode Example Display the log information from level 0 to level 5 in the log buffer: TP-LINK(config)# show logging buffer level 5 show logging flash Description The show logging flash level command is used to display the log information in the log file according to the severity level.
Page 115 TL-SL5428E JetStream L2 Managed Switch CLI Guide Display the log information with the level marked 0~3 in the log file: TP-LINK(config)# show logging flash level 3...
Page 116: Chapter 19 Ssh Commands
Command Mode Global Configuration Mode Example Enable the SSH function: TP-LINK(config)# ssh server enable ssh version Description The ssh version command is used to enable the SSH protocol version. To disable the protocol version, please use no ssh version command.
Page 117: Ssh Idle-Timeout
TL-SL5428E JetStream L2 Managed Switch CLI Guide Enable SSH v2: TP-LINK(config)# ssh version v2 ssh idle-timeout Description The ssh idle-timeout command is used to specify the idle-timeout time of SSH. To restore to the factory defaults, please use no ssh idle-timeout command.
Page 118: Ssh Download
Example Download a SSH-1 type key file named ssh-key from TFTP server with the IP Address 192.168.0.148: TP-LINK(config)# ssh download v1 ssh-key ip-address 192.168.0.148 show ssh Description The show ssh command is used to display the global configuration of SSH.
Page 119 TL-SL5428E JetStream L2 Managed Switch CLI Guide Example Display the global configuration of SSH: TP-LINK(config)# show ssh...
Page 120: Chapter 20 Ssl Commands
Command Mode Global Configuration Mode Example Enable the SSL function: TP-LINK(config)# ssl enable ssl download certificate Description The ssl download certificate command is used to download a certificate to the switch from TFTP server. Syntax...
Page 121: Ssl Download Key
Example Download a SSL Certificate named ssl-cert from TFTP server with the IP Address of 192.168.0.148: TP-LINK(config)# ssl download certificate ssl-cert ip-address 192.168.0.148 ssl download key Description The ssl download key command is used to download a SSL key to the switch from TFTP server.
Page 122 TL-SL5428E JetStream L2 Managed Switch CLI Guide Command Mode Any Configuration Mode Example Display the global configuration of SSL: TP-LINK(config)# show ssl...
Page 123: Chapter 21 Address Commands
TL-SL5428E JetStream L2 Managed Switch CLI Guide Chapter 21 Address Commands Address configuration can improve the network security by configuring the Port Security and maintaining the address information by managing the Address Table. bridge address port-security Description The bridge address port-security command is used to configure port security.
Page 124: Bridge Address Static
—— The Port number of your desired entry. It ranges from 1 to 28. Command Mode Global Configuration Mode Example Add a static Mac address entry to bind the MAC address 00:02:58:4f:6c:23, VLAN1 and Port1 together: TP-LINK(config)# bridge address static mac 00:02:58:4f:6c:23 vid 1 port 1...
Page 125: Bridge Aging-Time
Command Mode Global Configuration Mode Example Configure the aging time as 500 seconds: TP-LINK(config)# bridge aging-time 500 bridge address filtering Description The bridge address filtering command is used to add the filtering address entry. To delete the corresponding entry, please use no bridge address filtering command.
Page 126: Show Bridge Port-Security
Global Configuration Mode Example Add a filtering address entry whose VLAN ID is 1 and MAC address is 00:1e:4b:04:01:5d: TP-LINK(config)# bridge address filtering 00:1e:4b:04:01:5d 1 show bridge port-security Description The show bridge port-security command is used to configure the Port Security for each port, such as configure the Max number of MAC addressed that can be learned on the port and the Learn Mode.
Page 127: Show Bridge Aging-Time
JetStream L2 Managed Switch CLI Guide Any Configuration Mode Example Display the information of all Address entries: TP-LINK(config)# show bridge address all show bridge aging-time Description The show bridge aging-time command is used to display the Aging Time of the MAC address.
Page 128: Chapter 22 System Commands
—— Contact Information. It consists of 32 characters at most. By default, it is empty. Command Mode Global Configuration Mode Example Configure the System Contact as www.tp-link.com.cn: TP-LINK(config)# system-descript contact-info www.tp-link.com.cn system-time gmt Description The system-time gmt command is used to configure the time zone and the IP Address for the NTP Server.
Page 129: System-Time Manual
Example Configure the system time mode as gmt, the time zone is -12, the primary ntp server is 133.100.9.2 and the secondary ntp server is 139.78.100.163: TP-LINK(config)# system-time gmt -12 133.100.9.2 139.78.100.163 system-time manual Description The system-time manual command is used to configure the system time manually.
Page 130: Ip Address
Global Configuration Mode Example Configure the dst, dst is from April 1 00:00 to November 1 23:00. TP-LINK(config)# system-time dst 04/01 0 11/01 23 ip address Description The ip address command is used to configure the IP Address, Subnet Mask and Default Gateway.
Page 131: Ip Management-Vlan
Command Mode Global Configuration Mode Example Set the VLAN6 as IP management VLAN: TP-LINK(config)# ip management-vlan 6 ip dhcp-alloc Description The ip dhcp-alloc command is used to enable the DHCP Client function. When this function is enabled, the switch will obtain IP from DHCP Client server.
Page 132: Reset
Command Mode Global Configuration Mode Example Enable the BOOTP Protocol to obtain IP address from BOOTP Server: TP-LINK(config)# ip bootp-alloc reset Description The reset command is used to reset the switch’s software. After resetting, all configuration of the switch (except the IP Address) will restore to the factory defaults and your current settings will be lost.
Page 133: User-Config Backup
Privileged EXEC Mode Example Backup the configuration files by TFTP server with the IP 192.168.0.148 and name this file config.cfg: TP-LINK# user-config backup filename config.cfg ip-address 192.168.0.148 user-config load Description The user-config load command is used to download the configuration file to the switch by TFTP server.
Page 134: User-Config Save
TL-SL5428E JetStream L2 Managed Switch CLI Guide 192.168.0.148 and name this file config.cfg: TP-LINK# user-config load filename config.cfg ip-address 192.168.0.148 user-config save Description The user-config save command is used to save current settings. Syntax user-config save Command Mode Privileged EXEC Mode...
Page 135: Ping
192.168.0.131, please specify the count (-l) as 512 bytes and count (-i) as 1000 milliseconds. If there is not any response after 8 times’ Ping test, the connection between the switch and the network device is failed to establish: TP-LINK# ping 192.168.0.131 –n 8 –l 512 tracert Description The tracert command is used to test the connectivity of the gateways during its journey from the source to destination of the test data.
Page 136: Loopback
192.168.0.131. If the destination device has not been found after 20 maxHops, the connection between the switch and the destination device is failed to establish: TP-LINK# tracert 192.168.0.131 20 loopback Description The loopback command is used to test whether the port is available or not.
Page 137: Show Ip Address
Syntax show ip address Command Mode Any Configuration Mode Example Display the IP Address of the system TP-LINK# show ip address show system-time Description The show system-time command is used to display the time information of the switch. Syntax show system-time...
Page 138: Show System-Time Dst
Description The show system-time dst command is used to display the DST time information of the switch. Syntax show system-time dst Command Mode Any Configuration Mode Example Display the DST time information of the switch TP-LINK# show system-time dst...
Page 139: Chapter 23 Ethernet Configuration Commands
Command Mode Global Configuration Mode Example Enter the Interface Configuration Mode and configure Ethernet port2: TP-LINK(config)# interface ethernet 2 interface range ethernet Description The interface range ethernet command is used to enter the Interface Configuration Mode and configure multiple Ethernet ports at the same time.
Page 140: Description
Example Enter the Interface Configuration Mode, add ports 1-3, 6-9 to the port-list and configure them: TP-LINK(config)# interface range ethernet 1-3,6-9 description Description The description command is used to add a description to the Ethernet port. To clear the description of the corresponding port, please use no description command.
Page 141: Flow-Control
Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Disable Ethernet port3: TP-LINK(config)# interface ethernet 3 TP-LINK(config-if)# shutdown flow-control Description The flow-control command is used to enable the flow-control function for a port. To disable the flow-control function for this corresponding port, please use no flow-control command.
Page 142: Storm-Control
Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Configure the Negotiation Mode as 100M full-duplex for Ethernet port5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# negotiation 100f storm-control Description The storm-control command is used to configure the Storm Control function.
Page 143: Storm-Control Disable Bc-Rate
Enable the Storm Control function for port5 and specify the bc-rate as 100kbps, mc-rate as 500kbps and ul-rate as 2Mbps: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# storm-control bc-rate 100k mc-rate 500k ul-rate 2m storm-control disable bc-rate Description The storm-control disable bc-rate command is used to disable the Broadcast packets control.
Page 144: Storm-Control Disable Ul-Rate
TL-SL5428E JetStream L2 Managed Switch CLI Guide Disable the Multicast packets control for port5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# storm-control disable mc-rate storm-control disable ul-rate Description The storm-control disable ul-rate command is used to disable the UL-Frame control. Syntax storm-control disable ul-rate Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet）...
Page 145: Port Rate-Limit Disable Ingress
JetStream L2 Managed Switch CLI Guide Configure the ingress-rate as 10Mbps and egress-rate as 1Mbps for port5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# port rate-limit ingress 10m egress 1m port rate-limit disable ingress Description The port rate-limit disable ingress command is used to disable the ingress-rate limit.
Page 146: Show Interface Configuration
Command Mode Any Configuration Mode Example Display the configurations of port5: TP-LINK# show interface configuration ethernet 5 show interface status Description The show interface status command is used to display the connective-status of an Ethernet port.
Page 147: Show Interface Counters
Command Mode Any Configuration Mode Example Display the statistic information of Ethernet port3: TP-LINK(config)# show interface counters ethernet 3 show storm-control ethernet Description The show storm-control ethernet command is used to display the storm-control information of an Ethernet port.
Page 148: Show Port Rate-Limit
— — The port-number of the port selected to display the rate-limit information. It ranges from 1 to 28. By default, the rate-limit information of all ports is displayed. Command Mode Any Configuration Mode Example Display the rate-limit information of all Ethernet ports: TP-LINK(config)# show port rate-limit...
Page 149: Chapter 24 Qos Commands
CoS value of the ingress port and the mapping relation between the CoS and TC in IEEE 802.1P. Example Configure the priority of port 5 as 3: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# qos 3 qos dot1p enable Description The qos dot1p enable command is used to enable the mapping relation between IEEE 802.1P Priority and Egress Queue.
Page 150: Qos Dot1P Config
Command Mode Global Configuration Mode Example Enable the mapping relation between IEEE 802.1P Priority and Egress Queue: TP-LINK(config)# qos dot1p enable qos dot1p config Description The qos dot1p config command is used to configure the mapping relation between IEEE 802.1P Priority and Egress Queue. To return to the default configuration, please use no qos dot1p config command.
Page 151: Qos Dscp Enable
TL-SL5428E JetStream L2 Managed Switch CLI Guide Example Map tag value 0 to TC3: TP-LINK(config)# qos dot1p config 0 3 qos dscp enable Description The qos dscp enable command is used to enable the mapping relation between DSCP Priority and Egress Queue. To disable the mapping relation, please use no qos dscp enable command.
Page 152: Qos Scheduler
Among the priority levels TC0-TC3, the bigger value, the higher priority. Example Map DSCP values 10,11,15 to TC0: TP-LINK(config)# qos dscp config 10,11,15 0 qos scheduler Description The qos scheduler command is used to configure the Schedule Mode. To return to the default configuration, please use no qos scheduler command.
Page 153: Show Qos Port-Based
—— The Ethernet port selected to display the configuration, ranging from 1 to 28. By default, information of all the ports is displayed. Command Mode Any Configuration Mode Example Display the configuration of QoS for port 5: TP-LINK# show qos port-based 5...
Page 154: Show Qos Dot1P
Syntax show qos dot1p Command Mode Any Configuration Mode Example Display the configuration of IEEE 802.1P Priority: TP-LINK# show qos dot1p show qos dscp Description The show qos dscp command is used to display the configuration of DSCP Priority. Syntax...
Page 155 TL-SL5428E JetStream L2 Managed Switch CLI Guide Any Configuration Mode Example Display the schedule rule of the egress queues: TP-LINK# show qos scheduler...
Page 156: Chapter 25 Port Mirror Commands
Command Mode Interface Configuration Mode（interface ethernet） Example Configure port 1 as mirroring port: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# port mirror port mirrored Description The port mirrored command is used to configure the port monitoring. To delete the corresponding configuration, please use no port mirrored command.
Page 157: Show Port Mirror
Configure port 2,5,6,7 and 9 as mirrored ports, port 1 as the mirroring port, and enable ingress monitoring: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# port mirror TP-LINK(config-if)# port mirrored 2,5-7,9 ingress show port mirror Description The show port mirror command is used to display the configuration of port monitoring.
Page 158: Chapter 26 Port Isolation Commands
Command Mode Interface Configuration Mode Example Configure port 1 and port 2 can only forward packets to port 6 and port 13: TP-LINK(config)# interface range ethernet 1-2 TP-LINK(config-if)# port isolation 6,13 show port isolation Description The show port isolation command is used to display the forward portlist of a port.
Page 159 TL-SL5428E JetStream L2 Managed Switch CLI Guide Any Configuration Mode Example Display the forward-list of port 6: TP-LINK# show port isolation...
Page 160: Chapter 27 Acl Commands
TL-SL5428E JetStream L2 Managed Switch CLI Guide Chapter 27 ACL Commands ACL (Access Control List) is used to filter data packets by configuring a series of match conditions, operations and time ranges. It provides a flexible and secured access control policy and facilitates you to control the network security.
Page 161: Acl Edit Time-Segment
Command Mode Global Configuration Mode Example Add a time-range named tSeg1, with time from 8:30 to 12:00 at working day: TP-LINK(config)# acl time-segment tSeg1 start-time 08:30 end-time 12:00 week-day working-day acl edit time-segment Description The acl edit time-segment command is used to edit Time-Range.
Page 162: Acl Holiday
TL-SL5428E JetStream L2 Managed Switch CLI Guide Example Edit the time-range named tSeg1, with time from 8:30 to 12:00 at working day: TP-LINK(config)# acl edit time-segment tSeg1 start-time 08:30 end-time 12:00 week-day working-day acl holiday Description The acl holiday command is used to create holiday in Holiday Mode in the acl time-segment command.
Page 163: Acl Rule Mac-Acl
Command Mode Global Configuration Mode Example Create a MAC ACL whose ID is 20: TP-LINK(config)# acl create 20 acl rule mac-acl Description The acl rule mac-acl command is used to add MAC ACL rule. To delete the corresponding rule, please use no acl rule mac-acl command. MAC ACLs...
Page 164: Acl Edit Rule Mac-Acl
TP-LINK(config)# acl create 20 TP-LINK(config)# acl rule mac-acl 20 10 op permit smac 00:01:3F:48:16:23 smask 11:11:11:11:11:00 vid 2 pri 5 tseg tSeg1 acl edit rule mac-acl Description The acl edit rule mac-acl command is used to edit MAC ACL rule.
Page 165: Acl Rule Std-Acl
11:11:11:11:11:00, VLAN ID is 2, the user priority is 5, the time-range for the rule to take effect is tSeg1, and the packets match this rule will be forwarded by the switch: TP-LINK(config)# acl edit rule mac-acl 20 10 op permit smac 00:01:3F:48:16:23 smask 11:11:11:11:11:00 vid 2 pri 5 tseg tSeg1 acl rule std-acl Description The acl rule std-acl command is used to add Standard-IP ACL rule.
Page 166: Acl Edit Rule Std-Acl
255.255.255.0, the time-range for the rule to take effect is tSeg1, and the packets match this rule will be forwarded by the switch: TP-LINK(config)# acl create 120 TP-LINK(config)# acl rule std-acl 120 10 op permit dip 192.168.0.100 dmask 255.255.255.0 tseg tSeg1 acl edit rule std-acl...
Page 167 IP address is 192.168.0.100, the source IP address mask is 255.255.255.0, the time-range for the rule to take effect is tSeg1, and the packets match this rule will be forwarded by the switch: TP-LINK(config)# acl rule std-acl 120 10 op permit dip 192.168.0.100 dmask 255.255.255.0 tseg tSeg1...
Page 168: Acl Policy Policy-Add
Command Mode Global Configuration Mode Example Add a Policy named policy1: TP-LINK(config)# acl policy policy-add policy1 acl policy action-add Description The acl policy action-add command is used to add ACLs and create actions for the policy. To delete the corresponding actions, please use no acl policy action-add command.
Page 169: Acl Edit Action
Create a Policy named policy1. For the data packets those match ACL 120 in the policy, if the rate beyond 1000kbps, will be discarded by the switch: TP-LINK(config)# acl policy policy-add policy1 TP-LINK(config)# acl policy action-add policy1 120 rate 1000 osd discard acl edit action Description The acl edit action command is used to edit actions for the policy.
Page 170: Acl Bind To-Port
Edit the actions for the policy1. For the data packets those match ACL 120 in the policy, if the rate beyond 1000kbps, will be discarded by the switch: TP-LINK(config)# acl edit action policy1 120 rate 1000 osd discard acl bind to-port Description The acl bind to-port command is used to bind a policy to a port.
Page 171: Acl Bind To-Vlan
Command Mode Global Configuration Mode Example Bind policy1 to Port 1: TP-LINK(config)# acl bind to-port policy1 1 acl bind to-vlan Description The acl bind to-vlan command is used to bind a policy to a VLAN. To cancel the bind relation, please use no policy to-vlan command.
Page 172: Show Acl Holiday
Command Mode Any Configuration Mode Example Display the configuration of the MAC ACL whose ID is 20: TP-LINK> show acl config 20 show acl bind Description The show acl bind command is used to display the configuration of Policy bind.
Page 173 TL-SL5428E JetStream L2 Managed Switch CLI Guide Command Mode Any Configuration Mode Example Display the configuration of Policy bind: TP-LINK> show acl bind...
Page 174: Chapter 28 Mstp Commands
TL-SL5428E JetStream L2 Managed Switch CLI Guide Chapter 28 MSTP Commands MSTP (Multiple Spanning Tree Protocol), compatible with both STP and RSTP and subject to IEEE 802.1s, can disbranch a ring network. STP is to block redundant links and backup links as well as optimize paths.
Page 175: Spanning-Tree Common-Config
4096, Hello Time as 4 seconds, Max Age as 10 seconds, Forward Delay as 10 seconds, TxHold Count as 8pps and Max Hops as 15 hops: TP-LINK(config)# spanning-tree global status enable mode mstp cist 4096 htime 4 mage 10 delay 10 hcount 8 mhop 15...
Page 176: Spanning-Tree Region
Enable the STP function of port 1, and configure the Port Priority as 64, ExtPath Cost as 100, IntPath Cost as 100, and then enable Edge Port: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# spanning-tree common-config status enable pri 64 expath 100 inpath 100 edge enable spanning-tree region Description The spanning-tree region command is used to configure the region of MSTP.
Page 177: Spanning-Tree Msti
Command Mode Global Configuration Mode Example Configure the region name of MSTP as r1, and the revision level as 100: TP-LINK(config)# spanning-tree region r1 100 spanning-tree msti Description The spanning-tree msti command is used to configure MSTP Instance. To return to the default configuration of the corresponding Instance, please use no spanning-tree msti command.
Page 178: Spanning-Tree Msti
Example Enable Instance 1, add VLAN 2, 3, 4, 5, 8 for it, and configure MSTI Priority as 4096: TP-LINK(config)# spanning-tree msti 1 status enable pri 4096 mapped 2-5,8 spanning-tree msti Description The spanning-tree msti command is used to configure MSTP Instance Port. To return to the default configuration of the corresponding Instance Port, please use no spanning-tree msti command.
Page 179: Spanning-Tree Tc-Defend
Command Mode Global Configuration Mode Example Configure TC Threshold as 30 packets, and TC Protect Cycle as 10 seconds: TP-LINK(config)# spanning-tree tc-defend threshold 30 period 10 spanning-tree security Description The spanning-tree security command is used to configure MSTP Port Protect.
Page 180: Spanning-Tree Mcheck
Example Enable Loop Protect, Root Protect, TC Protect, BPDU Protect, and BPDU Filter for port 2: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# spanning-tree security loop enable root enable TC enable defend enable hold enable spanning-tree mcheck Description The spanning-tree mcheck command is used to enable MCheck.
Page 181: Show Spanning-Tree Global-Info
Command Mode Any Configuration Mode Example Display the current status of Spanning Tree: TP-LINK# show spanning-tree global-info show spanning-tree global-config Description The show spanning-tree global-config command is used to display the global configuration of Spanning Tree. Syntax...
Page 182: Show Spanning-Tree Region
By default, the configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the configuration of port 5: TP-LINK(config)# show spanning-tree port-config 5 show spanning-tree region Description The show spanning-tree region command is used to display the Region configuration of MSTP.
Page 183: Show Spanning-Tree Msti Port
Command Mode Any Configuration Mode Example Display the configuration of port 5 in Instance 1: TP-LINK(config)# show spanning-tree msti port 1 5 show spanning-tree security tc-defend Description The show spanning-tree security tc-defend command is used to display TC Threshold and TC Protect Cycle of Spanning Tree.
Page 184: Show Spanning-Tree Security Port-Defend
—— The port selected to display the configuration, ranging from 1 to 28. By default, the Port Protect configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the Port Protect configuration of port 2: TP-LINK(config)# show spanning-tree security port-defend 2...
Page 185: Chapter 29 Igmp Commands
Command Mode Global Configuration Mode Example Enable IGMP Snooping function, and specify the operation to process unknown multicast as discard: TP-LINK(config)# igmp-snooping global status enable unknown-packet discard igmp-snooping config Description The igmp-snooping config status command is used to configure IGMP...
Page 186: Igmp-Snooping Vlan-Config-Add
Interface Configuration Mode（interface ethernet / interface range ethernet） Example Enable IGMP Snooping and Fast Leave function for port 5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# igmp-snooping config status enable fast-leave enable igmp-snooping vlan-config-add Description The igmp-snooping vlan-config-add command is used to configure IGMP Snooping parameters for individual VLANs.
Page 187: Igmp-Snooping Vlan-Config
Enable IGMP Snooping for VLAN 1, and configure Router Port Time as 200 seconds, Member Port Time as 100 seconds, Leave time as 10 seconds and Static Router Port as port 1: TP-LINK(config)# igmp-snooping vlan-config-add 1 rtime 200 mtime 100 ltime 10 rport 1 igmp-snooping vlan-config...
Page 188: Igmp-Snooping Multi-Vlan-Config
Example Modify Router Port Time as 300 seconds, Member Port Time as 200 seconds, and Leave time as 15 seconds for VLAN 1: TP-LINK(config)# igmp-snooping vlan-config 1 rtime 300 mtime 200 ltime 15 igmp-snooping multi-vlan-config Description The igmp-snooping multi-vlan-config command is used to create Multicast VLAN.
Page 189: Igmp-Snooping Static-Entry-Add
Example Enable Multicast VLAN, and configure Router Port Time as 300 seconds, Member Port Time as 200 seconds, and Leave time as 15 seconds for VLAN 2: TP-LINK(config)# igmp-snooping multi-vlan-config enable 2 rtime 300 mtime 200 ltime 15 igmp-snooping static-entry-add...
Page 190: Igmp-Snooping Filter-Add
Global Configuration Mode Example Add static multicast IP address 225.0.0.1, which correspond to VLAN 2, and configure the forward port as port 1: TP-LINK(config)# igmp-snooping static-entry-add 225.0.0.1 2 1 Igmp-snooping filter-add Description The igmp-snooping filter-add command is used to configure the multicast IP-range desired to filter.
Page 191: Igmp-Snooping Filter
Command Mode Global Configuration Mode Example Modify the multicast IP-range whose ID is 20 as 225.0.0.10~225.0.0.12: TP-LINK(config)# igmp-snooping filter- config 20 225.0.0.10 225.0.0.12 igmp-snooping filter Description The igmp-snooping filter command is used to configure Port Filter. To return to the default configuration, please use no igmp-snooping filter command. When...
Page 192: Show Igmp-Snooping Global-Config
IP-range 2, 3, 4, and specify the maximum number of multicast groups for port 5 to join in as 128: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# igmp-snooping filter status enable mode accept addr-id 2-4 maxgroup 128 show igmp-snooping global-config Description The show igmp-snooping global-config command is used to display the global configuration of IGMP.
Page 193: Show Igmp-Snooping Vlan-Config
By default, the configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the IGMP configuration of port 2: TP-LINK> show igmp-snooping port-config 2 show igmp-snooping vlan-config Description The show igmp-snooping vlan-config command is used to display the VLAN configuration of IGMP.
Page 194: Show Igmp-Snooping Multi-Ip-List
TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK> show igmp-snooping multi-vlan show igmp-snooping multi-ip-list Description The show igmp-snooping multi-ip-list command is used to display the Multicast IP table. Syntax show igmp-snooping multi-ip-list Command Mode Any Configuration Mode Example Display the Multicast IP table: TP-LINK>...
Page 195: Show Igmp-Snooping Packet-Stat
1 to 28. By default, the configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the Multicast Filter configuration of port 5: TP-LINK> show igmp-snooping port-filter 5 show igmp-snooping packet-stat Description The show igmp-snooping packet-stat command is used to display the Packet Statistics information of all ports.
Page 196 TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK> show igmp-snooping packet-stat-clear...
Page 197: Chapter 30 Snmp Commands
10 to 64 hexadecimal characters, which must be even number meanwhile. Command Mode Global Configuration Mode Example Enable the SNMP function, and specify the Local Engine ID as 1234567890, the Remote Engine ID as 123456abcdef: TP-LINK(config)# snmp global status enable engine-id 1234567890 remote-id 123456abcdef...
Page 198: Snmp View-Add
Example Add a View named view1, configuring the OID as 1.3.6.1.6.3.20, and this OID can be managed by the SNMP management station: TP-LINK(config)# snmp view-add view1 1.3.6.1.6.3.20 include snmp group-add Description The snmp group-add command is used to manage and configure the SNMP group.
Page 199 Add group 1, configure its Security Model as SNMP v2c, view1 can be read and edited by group member, and the trap messages sent by view2 can be received by Management station: TP-LINK(config)# snmp group-add group1 smode v2c ro view1 wo view1 inform view2...
Page 200: Snmp User-Add
TL-SL5428E JetStream L2 Managed Switch CLI Guide snmp user-add Description The snmp user-add command is used to add User. To delete the corresponding User, please use no snmp user-add command. The User in a SNMP Group can manage the switch via the management station software. The User and its Group have the same security level and access right.
Page 201: Snmp Community-Add
MD5, the Authentication Password as 11111, the Privacy Mode as DES, and the Privacy Password as 22222: TP-LINK(config)# snmp user-add admin local group2 smode v3 slev authPriv cmode MD5 cpwd 11111 emode DES epwd 22222 snmp community-add Description The snmp community-add command is used to add Community.
Page 202: Snmp Notify-Add
TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK(config)# snmp community-add community1 read-write view1 snmp notify-add Description The snmp notify-add command is used to add Notification. To delete the corresponding Notification, please use no snmp notify-add command. With the Notification function enabled, the switch can initiatively report to the management station about the important events that occur on the Views, which allows the management station to monitor and process the events in time.
Page 203: Snmp-Rmon History Sample-Cfg
Security Model of the management station as v2c, the type of the notifications as inform, the maximum time for the switch to wait as 1000 seconds, and the resending time as 100: TP-LINK(config)# snmp notify-add 192.168.0.1 162 admin smode v2c type inform resend 100 timeout 1000 snmp-rmon history sample-cfg...
Page 204: Snmp-Rmon History Owner
Example Configure the sample port as 1, and the sample interval as 100 seconds for the entries 1-3: TP-LINK(config)# snmp-rmon history sample-cfg 1-3 1 100 snmp-rmon history owner Description The snmp-rmon history owner command is used to configure the owner of the history sample entry.
Page 205: Snmp-Rmon Event User
—— The name of the User to which the event belongs, ranging from 1 to 16 characters. By default, it is public. Command Mode Global Configuration Mode Example Configure the user name of entry 1 as user1: TP-LINK(config)# snmp-rmon event user 1 user1...
Page 206: Snmp-Rmon Event Description
Command Mode Global Configuration Mode Example Configure the description of entry 1 as description1: TP-LINK(config)# snmp-rmon event description 1 description1 snmp-rmon event type Description The snmp-rmon event type command is used to configure the type of SNMP-RMON Event. To return to the default configuration, please use no snmp-rmon event type command.
Page 207: Snmp-Rmon Event Owner
Command Mode Global Configuration Mode Example Configure the event type of entries 1,2,3,4 and 8 as log: TP-LINK(config)# snmp-rmon event type 1-4,8 log snmp-rmon event owner Description The snmp-rmon event owner command is used to configure the owner of SNMP-RMON Event. To return to the default configuration, please use no snmp-rmon event owner command.
Page 208: Snmp-Rmon Alarm Config
Command Mode Global Configuration Mode Example Enable the SNMP-RMON Event entries 1,2,3,4 and 8: TP-LINK(config)# snmp-rmon event enable 1-4,8 snmp-rmon alarm config Description The snmp-rmon alarm config command is used to configure SNMP-RMON Alarm Management. To return to the default configuration, please use no snmp-rmon alarm config command.
Page 209: Snmp-Rmon Alarm Owner
Global Configuration Mode Example Configure the alarm interval time of the entries 1,2,3 and 6 as 1000 seconds: TP-LINK(config)# snmp-rmon alarm config 1-3,6 interval 1000 snmp-rmon alarm owner Description The snmp-rmon alarm owner command is used to configure the owner of the Alarm Management entry.
Page 210: Snmp-Rmon Alarm Enable
Command Mode Global Configuration Mode Example Configure the owner of entry 1 as owner1: TP-LINK(config)# snmp-rmon alarm owner 1 owner1 snmp-rmon alarm enable Description The snmp-rmon alarm enable command is used to enable SNMP-RMON Alarm Management entry. To disable the corresponding entry, please use no snmp-rmon alarm enable command.
Page 211: Show Snmp View
Syntax show snmp global-config Command Mode Any Configuration Mode Example Display SNMP configuration globally: TP-LINK> show snmp global-config show snmp view Description The show snmp view command is used to display the View table. Syntax show snmp view Command Mode...
Page 212: Show Snmp User
Syntax show snmp user Command Mode Any Configuration Mode Example Display the User table: TP-LINK> show snmp user show snmp community Description The show snmp community command is used to display the Community table. Syntax show snmp community Command Mode...
Page 213: Show Snmp-Rmon History
TL-SL5428E JetStream L2 Managed Switch CLI Guide Display the Notification table: TP-LINK> show snmp destination-host show snmp-rmon history Description The show snmp-rmon history command is used to display the configuration of the history sample entry. Syntax show snmp-rmon history [index] Parameter index ——...
Page 214: Show Snmp-Rmon Alarm
TL-SL5428E JetStream L2 Managed Switch CLI Guide Display the Event configuration of entry 2: TP-LINK> show snmp-rmon event 2 show snmp-rmon alarm Description The show snmp-rmon alarm command is used to display the configuration of the Alarm Management entry. Syntax...
Page 215: Chapter 31 Cluster Commands
Time ranges from 5 to 254 in seconds. By default, it is 60. Command Mode Global Configuration Mode Example Enable NDP function globally, and configure Aging Time as 120 seconds, Hello Time as 50 seconds: TP-LINK(config)# cluster ndp status enable aging-timer 120 hello-timer 50...
Page 216: Cluster Ntdp
TL-SL5428E JetStream L2 Managed Switch CLI Guide cluster ntdp Description The cluster ntdp command is used to configure NTDP globally. To return to the default configuration, please use no cluster ntdp command. NTDP (Neighbor Topology Discovery Protocol) is used to collect the NDP information and neighboring connection information of each device in a specific network range.
Page 217: Cluster Explore
TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK(config)# cluster ntdp status enable interval 20 hop 5 hop-delay 300 port-delay 50 cluster explore Description The cluster explore command is used to enable the topology information collecting function manually. Syntax cluster explore...
Page 218: Cluster Create
Example Specify the current switch as commander switch, create cluster c1, and configure the cluster IP address pool as 10.90.90.1~10.90.90.254: TP-LINK(config)# cluster create c1 10.90.90.10 255.255.255.0 cluster manage config Description The cluster manage config command is used to configure Cluster.
Page 219: Cluster Manage Member
Global Configuration Mode Example Specify the Hold Time and Interval Time of cluster c1 as 50 seconds: TP-LINK(config)# cluster manage config c1 50 50 cluster manage member Description The cluster manage member command is used to add member switch. To delete the corresponding member, please use no cluster manage member command.
Page 220: Show Cluster Ndp Global
Command Mode Global Configuration Mode Example Change the role of the current switch to Commander Switch: TP-LINK(config)# cluster manage role-change candidate show cluster ndp global Description The show cluster ndp global command is used to display the global configuration of NDP.
Page 221: Show Cluster Neighbour
28. By default, the configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the NDP configuration of port 2: TP-LINK> show cluster ndp port-status 2 show cluster neighbour Description The show cluster neighbour command is used to display the cluster neighbor information.
Page 222: Show Cluster Ntdp Port-Status
1 to 28. By default, the configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the NTDP configuration of port 2: TP-LINK> show cluster ntdp port-status 2 show cluster ntdp device Description The show cluster ntdp device command is used to display the device table of NTDP.
Page 223: Show Cluster Manage Member
Command Mode Any Configuration Mode Example Display the global configuration of Cluster: TP-LINK> show cluster manage config show cluster manage member Description The show cluster manage member command is used to display the member information. Syntax...
Page 224 TL-SL5428E JetStream L2 Managed Switch CLI Guide TP-LINK(config)# show cluster manage role...

TP-Link JetStream TL-SL5428E Cli Reference Manual

Preface

Chapter 1 Using the CLI

Chapter 2 User Interface

Chapter 3 IEEE 802.1Q VLAN Commands

Chapter 4 MAC VLAN Commands

Chapter 5 Protocol VLAN Commands

Chapter 6 VLAN-VPN Commands

Chapter 7 Voice VLAN Commands

Chapter 8 Private VLAN Commands

Chapter 9 GVRP Commands

Chapter 10 LAG Commands

Chapter 11 LACP Commands

Chapter 12 User Manage Commands

Chapter 13 Binging Table Commands

Chapter 14 ARP Inspection Commands

Chapter 15 IP Source Guard Commands

Chapter 16 Dos Defend Command

Chapter 17 IEEE 802.1X Commands

Chapter 18 Log Commands

Chapter 19 SSH Commands

Chapter 20 SSL Commands

Chapter 21 Address Commands

Chapter 22 System Commands

Chapter 23 Ethernet Configuration Commands

Chapter 24 Qos Commands

Chapter 25 Port Mirror Commands

Chapter 26 Port Isolation Commands

Chapter 27 ACL Commands

Chapter 28 MSTP Commands

Chapter 29 IGMP Commands

Quick Links

Related Manuals for TP-Link JetStream TL-SL5428E

Summary of Contents for TP-Link JetStream TL-SL5428E