Alarm Indication; Function Mode/Dealer Program Mode - Gemini GEM-P816 Installation Instructions Manual

ALARM INDICATION

If programmed to silence an alarm, enter a valid User Code and press the
The keypad must have permission to disarm the alarm (Alarm, Pulse Alarm, PGM1 or PGM2 outputs) from the specific
area. This can be done through the PC Quickloader software, Area Features Screen or Area Bell Control. See Pro-
gramming Instructions (WI995 or WI1182) for specific address locations.
Should a burglary alarm occur, the red ARMED LED will flash, and the display will alternately read "ALARM", then the
zones violated. Disarm the panel; the display will read "ALARM" and will continue to indicate the violated zones until the
button is pressed or the panel is armed once again.
C

FUNCTION MODE/DEALER PROGRAM MODE

The keypad can provide a wide assortment of utility functions as summarized in the Keypad Function Mode. The
functions are displayed in a prompting "YES/NO" format. To skip a function, answer NO (press the PRIOR/NO button);
to select and execute a function, answer YES (press the
provided here in its normal displayed sequence. However, since not all functions are designed for all systems (or
intended for all users), only functions that are applicable and active are displayed. (For example, if no zones are
bypassed, "DISPLAY ZN BYPASSED" will not appear). Furthermore, functions that are intended for use by the installer or
servicer will not be displayed. Note: Functions may be manually scrolled forward or backward using the
buttons, respectively.
B
To return to normal keypad operation, press the
operating mode if no activity is detected for longer than one minute). Note: Due to space constraints, GEM-RP2ASe2/
GEM-K2AS message displays are abbreviated.
Remember: (1) Functions that are not active, not programmed and/or not applicable to the user's authority level will be
suppressed and will not display. (2) Press the PRIOR/NO button to skip a function; press the NEXT/YES button to
execute it. (3) The GEM-RP2ASe2/GEM-K2AS displays abbreviated messages that autoscroll.
DISPLAY ZN FAULTS
Press the NEXT/YES button to identify all unsecured zones (within the keypad's area) while disarmed. Press
NEXT/YES button to scroll through the zones. Manually bypassed zones will be indicated when displaying status.
DISPLAY ZN BYPASSED
Press NEXT/YES button to display zones that have been deactivated. Press NEXT/YES button to scroll through
the zones.
DISPLAY ZN DIRECTORY
Press NEXT/YES button to display a list of all programmed zone descriptions in the keypad area. Press NEXT/
YES button to scroll through the zones. To return to the system, press the
ACTIVATE BELL TEST
Press the NEXT/YES button to activate the burg relay output (while disarmed) for about 2 seconds. If the device does
not sound, it may be defective.
DISPLAY FIRE ALARM
To display Fire Zone(s) in alarm, access DISPLAY FIRE ALARM and scroll through the zones using the NEXT/
YES button. Correct the problem, then press the
DISPLAY FIRE TRBL
To display Fire Zone(s) in trouble, access DISPLAY FIRE TRBL and scroll through the zones using the NEXT/YES
button. Correct the problem, then press the
ACTIVATE CHIME
Press the NEXT/YES button to sound a tone at the keypad when a Chime Zone is violated. The duration of the tone is
programmable. To turn off the Chime Mode, press the NEXT/YES button at the DEACTIVATE CHIME function. Note:
Chime is disabled for protected zones while armed. Never Armed zones (such as a driveway sensor) will continue to
NAPCO Security Systems
R
button or the
P
button. (The keypad will automatically return to its normal
C
button to restore the "SYSTEM READY" condition.
C
button to restore the "SYSTEM READY" condition.
C
U
button.
U
button). The complete function list is
button at any time.
C
GEM-P816 Installation Instructions
Page 23
and
A