Bypassing Zones; Unbypassing Zones; Alarm Indication; Function Mode/Dealer Program Mode - Gemini GEM-P1664 Installation Instructions Manual

WI1424A 1/06
Global Arm/Disarm
In a partitioned system, any of 4 secured areas may be armed (or disarmed) from the Manager's Mode (if en-
abled). The Manager's Mode, is a low-security mode of operation. It provides quick access to other areas without
having to go to another keypad of another area.
To arm all areas assigned to the user, press
To disarm all areas assigned to the user, press

BYPASSING ZONES

Selective Bypass (Bypassing Specific Zones)
A Selective Bypass will bypass a specific zone that has Selective Bypass enabled, by pressing the
followed by the zone number. The zone will be unbypassed the next time the system is disarmed. Note: Security
Bypass is a option that requires a valid User Code to bypass zones. This feature is enabled at the factory and can be
disabled using existing address (global "Enable Security Bypass"). In addition, when new User Codes are entered, the
"User Area Option" must be enabled to allow the new User Code to bypass zones. See Programming Instructions
(WI1422 or WI1423) for more information.

UNBYPASSING ZONES

(Unbypassing Specific Zones)
To unbypass a specific zone that has been bypassed, press the
zone will be unbypassed the next time the system is armed.

ALARM INDICATION

If programmed to silence an alarm, enter a valid User Code and press the
The keypad must have permission to disarm the alarm (Alarm, Pulse Alarm, PGM1 or PGM2 outputs) from the specific
area. This can be done through the PC Quickloader software, Area Features Screen or Area Bell Control. See Pro-
gramming Instructions (WI1422 or WI1423) for specific address locations.
Should a burglary alarm occur, the red ARMED LED will flash, and the display will alternately read "ALARM", then the
zones violated. Disarm the panel; the display will read "ALARM" and will continue to indicate the violated zones until the
button is pressed or the panel is armed once again.
C

FUNCTION MODE/DEALER PROGRAM MODE

The keypad can provide a wide assortment of utility functions as summarized in the Keypad Function Mode. The
functions are displayed in a prompting "YES/NO" format. To skip a function, answer NO (press the PRIOR/NO button);
to select and execute a function, answer YES (press the
provided here in its normal displayed sequence. However, since not all functions are designed for all systems (or
intended for all users), only functions that are applicable and active are displayed. (For example, if no zones are
bypassed, "DISPLAY ZN BYPASSED" will not appear). Furthermore, functions that are intended for use by the installer or
servicer will not be displayed. Note: Functions may be manually scrolled forward or backward using the
) and buttons, respectively.
B
R
To return to normal keypad operation, press the
operating mode if no activity is detected for longer than one minute). Note: Due to space constraints, GEM-RP2ASe2/
GEM-K2AS message displays are abbreviated.
Remember: (1) Functions that are not active, not programmed and/or not applicable to the user's authority level will be
suppressed and will not display. (2) Press the PRIOR/NO button to skip a function; press the NEXT/YES button to
execute it. (3) The GEM-RP2ASe2/GEM-K2AS displays abbreviated messages that autoscroll.
DISPLAY ZN FAULTS
Press the YES button to identify all unsecured zones (within the keypad's area) while disarmed. Press NEXT but-
ton to scroll through the zones. Manually bypassed zones will be indicated when displaying status.
L
NAPCO Security Systems
9 G [User Code]
0 G [User Code]
button followed by the zone number. The
B
button or the
P
button. (The keypad will automatically return to its normal
C
X
U D
or .
U D
or .
U
button.
U
button). The complete function list is
GEM-P1664 Installation Instructions
Page 23
button
B
(or
A